 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 250 MHz QAM IF DOWNCONVERTER FEATURES * RF/LO FREQUENCY RANGE: 30-250 MHz * ON CHIP VCO * LOW DISTORTION AGC AMPLIFIER: -9 dBm IIP3 @ MIN Gain * ON CHIP VIDEO AMP: 3.0 Vp-p (VCC = 5 V) * SMALL 20 PIN SSOP PACKAGE * AVAILABLE ON TAPE AND REEL UPC2798GR DESCRIPTION NEC's UPC2798GR is a Silicon MMIC Downconverter manufactured with the NESATTMIII silicon bipolar process. This product consists of an input AGC amplifier, mixer, local oscillator, and video amplifier. It is housed in a small 20 pin SSOP package. The device is designed for use as an IF downconverter for digital CATV settops and cable modems utilizing QAM modulation. NEC's stringent quality assurance and test procedures ensure the highest reliability and performance. ELECTRICAL CHARACTERISTICS (TA = 25C, RF = 45 MHz, LO = 55 MHz, PLO = -10 dBm, unless otherwise specified) PART NUMBER PACKAGE OUTLINE SYMBOLS ICC CGMAX1 CGMAX2 CGMIN1 CGMIN2 IIP3 IIP3 ICC CGMAX1 CGMAX2 CGMIN1 CGMIN2 IIP3 PARAMETERS AND CONDITIONS Circuit Current (no input signal) Maximum Conversion Gain, VAGC = 4.0 V, pins G1A - G1B shorted Maximum Conversion Gain, VAGC = 4.0 V, pins G1A - G1B open Minimum Conversion Gain, VAGC = 1.0 V, pins G1A - G1B shorted Minimum Conversion Gain, VAGC = 1.0 V, pins G1A - G1B open Input Intercept Point, VAGC = 1.0 V, pins G1A - G1B shorted Input Intercept Point, VAGC = 1.0 V, pins G1A - G1B open Circuit Current (no input signal) Maximum Conversion Gain, VAGC = 4.0 V, pins G1A - G1B shorted Maximum Conversion Gain, VAGC = 4.0 V, pins G1A - G1B open Minimum Conversion Gain, VAGC = 1.0 V, pins G1A - G1B shorted Minimum Conversion Gain, VAGC = 1.0 V, pins G1A - G1B open Input Intercept Point, VAGC = 1.0 V, pins G1A - G1B open UNITS mA dB dB dB dB dBm dBm mA dB dB dB dB dBm mA MHz MHz MHz dB dB dB dB V V dBm -9 4.0 1.0 26 15.0 30 30 DC 25 -7 32 9 32.0 72.0 32.0 MIN 24.0 68.0 Total Block (VCC1 = 5 V, VCC2 = 5 V, RL = 1 k) 35.5 74.0 58.0 39.0 22.0 -14.0 -8.0 47.0 78.5 59.0 43.5 22.5 -7.5 23.0 28.0 250 250 150 60.0 81.0 43.0 45.0 76.0 UPC2798GR S20 TYP MAX Total Block (VCC1 = 5 V, VCC2 = 9 V, RL = 1 k) AGC Amplifier and Mixer Block (VCC1 = 5 V) ICC Circuit Current (no input signal) fRF fOSC fIF CGMAX CGMIN GCR NF VAGC (H) VAGC (L) AGC IIP3 RF Input Frequency Range OSC Frequency Range IF Output Frequency Range Maximum Conversion Gain, VAGC = 4.0 V Minimum Conversion Gain, VAGC = 1.0 V AGC Dynamic Range, VAGC = 1.0 to 4.0 V Noise Figure, SSB, VAGC = 4.0 V (MAX Gain) AGC Voltage High, at MAX Gain AGC Voltage Low, at MIN Gain AGC Input Intercept Point, at MIN Gain California Eastern Laboratories UPC2798GR ELECTRICAL CHARACTERISTICS (TA = 25C, RF = 45 MHz, LO = 55 MHz, PLO = -10 dBm, unless otherwise specified) PART NUMBER PACKAGE OUTLINE SYMBOLS ICC VOUT G1 G2 ICC VOUT G1 G2 AVS1 AVS2 IIP3 AVS1 AVS2 IIP3 BWG1 BWG2 RIN 1 RIN 2 CIN CMRR PSRR PARAMETERS AND CONDITIONS Circuit Current (no input signal) Output Voltage Differential Gain 1, pins G1A and G1B shorted, VOUT = 3.0 Vp-p Differential Gain 2, pins G1A and G1B open, VOUT = 3.0 Vp-p Circuit Current (no input signal) Output Voltage Differential Gain 1, Pins G1A and G1B shorted Differential Gain 2, Pins G1A and G1B open Single-ended Gain, pins G1A - G1B shorted Single-ended Gain, pins G1A - G1B open Input Intercept Point, pins G1A - G1B open, f1 = 9 MHz, f2 = 11 MHz Single-ended Gain, pins G1A - G1B shorted Single-ended Gain, pins G1A - G1B open Input Intercept Point, pins G1A - G1B open, f1 = 9 MHz, f2 = 11 MHz Bandwidth 1, G1 Bandwidth 2, G2 Input Resistance 1, G1 Input Resistance 2, G2 Input Capacitance, CIN Common Mode Rejection Ratio, VCM = 1.0 Vp-p, = 100 kHz Power Supply Rejection Ratio Rise Time Propagation Delay Time UNITS mA Vp-p V/V V/V mA Vp-p V/V V/V dB dB dBm dB dB dBm MHz MHz k k pF dB dB ns ns 17.0 MIN 9.0 Video Amp Block (VCC2 = 5 V, differential, RL = 1 k) 12.5 3.0 200 26 24.0 3.0 385 28.5 40.0 22.5 -11.5 45.0 23.5 -5.0 50 50 3.5 9.7 1.6 80 70 2.6 4.4 32.0 17.0 UPC2798GR S20 TYP MAX Video Amp Block (VCC2 = 9 V, differential, RL = 1 k) Video Amp Block (VCC2 = 5 V, single ended, RL = 50 ) Video Amp Block (VCC2 = 9 V, single ended, RL = 50 ) Video Amp Block (VCC2 = 5 or 9 V, common, RL = 1 k ) R D ABSOLUTE MAXIMUM RATINGS1 (TA = 25C) SYMBOLS VCC1 VCC2 PD TOP TSTG SYMBOLS VCC1 VCC2 PD TOP TSTG PARAMETERS Supply Voltage 1 (Mixer Block) Supply Voltage 2 (Video Amp Block) Power Dissipation, TA = 85C2 Operating Temperature Storage Temperature PARAMETERS Supply Voltage 1 (Mixer Block) Supply Voltage 2 (Video Amp Block) Power Dissipation, TA = 75C2 Operating Temperature Storage Temperature UNITS V V mW C C UNITS V V mW C C RATINGS 6.0 6.0 430 -40 to +85 -55 to +150 RATINGS 6.0 11.0 500 -40 to +75 -55 to +150 RECOMMENDED OPERATING CONDITIONS SYMBOL VCC1 VCC2 TA1 TA2 PARAMETER Supply Voltage 1 Supply Voltage 2 Operating Temp. Range 1* Operating Temp. Range 2** UNITS MIN TYP MAX V V C C 4.5 4.5 -40 -40 5.0 5.0 +25 +25 5.5 10.0 +85 +75 Notes: * @ VCC1 = VCC2 = 4.5 to 5.5 V ** @ VCC1 = 4.5 to 5.5 V, VCC2 = 4.5 to 10.0 V Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. Mounted on a 50 x 50 x 1.6 mm epoxy glass PWB. UPC2798GR TYPICAL CHARACTERISTICS (by measurement circuit 1: AGC Amp and Mixer Block) CIRCUIT CURRENT vs. SUPPLY VOLTAGE 50 no input signal TA = 25C VAGC = 0 V Total CONVERSION GAIN vs. INPUT FREQUENCY 30 VAGC = 4.0 V Circuit Current, ICC (mA) 40 Conversion Gain, CG (dB) 20 10 VAGC = 2.6 V 0 30 Mixer +AGC+VCO Video Amp 20 -10 VAGC = 0.0 V 10 -20 PRF = 60 dBm fOSC = fRF+5 MHZ, POSC = -10 dBm VCC = 5 V, TA = 25C 0 50 100 150 200 250 300 0 0 2 4 6 8 10 12 -30 Supply Voltage, VCC (V) Input Frequency, fRF (MHz) CONVERSION GAIN vs. IF FREQUENCY 30 VAGC = 4.0 V NOISE FIGURE vs. AGC VOLTAGE 30 Conversion Gain, CG (dB) 20 Noise Figure, NF (dB) 180 10 VAGC = 2.6 V 0 20 -10 VAGC = 0.0 V 10 -20 -30 0 fRF = 45 MHZ, PRF = -60 dBm fOSC = 50~200 MHZ, POSC = -10 dBm VCC = 5 V, TA = 25C 30 60 90 120 150 VCC = 5 V fRF = 100 MHZ fOSC = 120 MHZ POSC = -10 dBm TA = 25C DSB 0 1 2 3 4 5 0 IF Frequency, fIF (MHz) AGC Voltage, VAGC (V) CONVERSION GAIN vs. AGC VOLTAGE 30 VCC = 5 V fRF = 45 MHZ PRF = -60 dBm fOSC = 50 MHZ POSC = -10 dBm TA = 25C THIRD ORDER INTERMODULATION LEVEL AND OUTPUT POWER vs. INPUT POWER -10 VCC = 5 V VAGC = 0 V fRF1 = 44 MHZ fRF2 = 46 MHZ -30 fOSC = 55 MHZ POSC = -10 dBm TA = 25C -40 -20 -50 -60 -70 -80 Conversion Gain, CG (dB) 20 Output Power, POUT (dBm) POUT 10 IM3 0 -10 0 1 2 3 4 5 -90 -60 -50 -40 -30 -20 -10 0 AGC Voltage, VAGC (V) Input Power, PIN (dBm) UPC2798GR STANDARD CHARACTERISTICS (by measurement circuit 2: Video Amp, RL = 1 k, TA = 25C) DIFFERENTIAL GAIN vs. INPUT FREQUENCY 400 VCC = 9 V 40 DIFFERENTIAL GAIN vs. INPUT FREQUENCY Differential Gain (V/V) 300 Differential Gain (V/V) 30 VCC = 9 V VCC = 5 V 200 VCC = 5 V 20 100 G1A-G1B : short POUT = 1.5 Vp-p const. 0 0 20 40 60 80 100 10 G1A-G1B : open POUT = 1.5 V p-p const. 0 0 20 40 60 80 100 Input Frequency, fIN (MHz) Input Frequency, fIN (MHz) OUTPUT POWER vs. INPUT POWER (VIDEO AMP) 0 0 OUTPUT POWER vs. INPUT POWER (VIDEO AMP) VCC = 9 V VCC = 9 V Output Power, Pout (dBm) Output Power, Pout (dBm) -10 -10 VCC = 5 V -20 VCC = 5 V -30 -20 -40 fin = 10 MHZ G1A-G1B : open fin = 10 MHZ G1A-G1B : short -30 -40 -30 -20 -10 0 -50 -40 -30 -20 -10 0 10 Input Power, PIN (dBm) Input Power, PIN (dBm) DIFFERENTIAL GAIN vs. RESISTANCE 500 fin = 10 MHZ 400 Differential Gain (V/V) 300 200 VCC = 9 V 100 VCC = 5 V 0 short 30 43 56 100 246 2000 open Resistance () UPC2798GR STANDARD CHARACTERISTICS (by measurement circuit 3: Video Amp, RL = 50 , TA = 25C) GAIN vs. INPUT FREQUENCY 50 GAIN vs. INPUT FREQUENCY 50 Single-ended Gain, AVS (dB) 40 Single-ended Gain, AVS (dB) VCC2 = 5 V G1A-G1B: short 40 30 30 20 20 10 10 VCC2 = 5 V G1A-G1B: open 0 0.1 1 10 100 0 0.1 1 10 100 Input Frequency, fIN (MHz) Input Frequency, fIN (MHz) GAIN vs. INPUT FREQUENCY 50 50 GAIN vs. INPUT FREQUENCY Single-ended Gain, AVS (dB) 40 Single-ended Gain, AVS (dB) VCC2 = 9 V G1A-G1B: short 40 30 30 20 20 10 10 VCC2 = 9 V G1A-G1B: open 0 0.1 1 10 100 0 0.1 1 10 100 Input Frequency, fIN (MHz) Input Frequency, fIN (MHz) THIRD ORDER INTERMODULATION LEVEL AND OUTPUT POWER vs. INPUT POWER 20 THIRD ORDER INTERMODULATION LEVEL AND OUTPUT POWER vs. INPUT POWER 20 Output Power, POUT (dBm) 0 Output Power, POUT (dBm) POUT 0 POUT -20 -20 IM3 -40 -40 IM3 -60 VCC2 = 5 V f1 = 9 MHz f2 = 11 MHz G1A-G1B: open -60 VCC2 = 9 V f1 = 9 MHz f2 = 11 MHz G1A-G1B: open -80 -50 -40 -30 -20 -10 -80 -50 -40 -30 -20 -10 Input Power, PIN (dBm) Input Power, PIN (dBm) UPC2798GR TYPICAL CHARACTERISTICS (by measurement circuit 4: Total Block, fRF = 45 MHz, PRF = -60 dBm, Posc = -10 dBm) CONVERSION GAIN vs. IF FREQUENCY 80 CONVERSION GAIN vs. IF FREQUENCY 80 Conversion Gain, CG (dB) Conversion Gain, CG (dB) 60 VAGC = 4 V 60 VAGC = 4 V VAGC = 3 V 40 40 VAGC = 3 V 20 VCC1 = 5 V, VCC2 = 5 V G1A - G1B : short 1 K load, TA = 25C 0 0 40 VAGC = 1 V VAGC = 1 V 20 VCC1 = 5 V, VCC2 = 9 V G1A - G1B : short 1 K load, TA = 25C 80 120 160 0 0 40 80 120 160 IF Frequency, fIF (MHz) IF Frequency, fIF (MHz) CONVERSION GAIN vs. IF FREQUENCY 80 CONVERSION GAIN vs. IF FREQUENCY 80 Conversion Gain, CG (dB) 60 Conversion Gain, CG (dB) 60 40 VAGC = 4 V VAGC = 4 V 40 20 VCC1 = 5 V, VCC2 = 5 V G1A - G1B : open 1 K load, TA = 25C 0 0 40 80 VAGC = 3 V VAGC = 3 V 20 VCC1 = 5 V, VCC2 = 9 V G1A - G1B : open 1 K load, TA = 25C 0 120 160 0 40 80 120 160 IF Frequency, fIF (MHz) IF Frequency, fIF (MHz) UPC2798GR TYPICAL CHARACTERISTICS (by measurement circuit 4: Total Block, PRF = -60 dBm, fOSC = fRF + 10 MHz, POSC = -10 dBm) CONVERSION GAIN vs. INPUT FREQUENCY 80 VAGC = 4 V CONVERSION GAIN vs. INPUT FREQUENCY 80 VAGC = 4 V Conversion Gain, CG (dB) 60 VAGC = 3 V Conversion Gain, CG (dB) VAGC = 3 V 60 VAGC = 1 V 40 40 VAGC = 1 V 20 0 0 VCC1 = 5 V VCC2 = 5 V 1 K load G1A-G1B : short TA = 25C 50 100 150 200 250 20 0 0 VCC1 = 5 V VCC2 = 9 V 1 K load G1A-G1B : short TA = 25C 50 100 150 200 250 Input Frequency, fRF (MHz) Input Frequency, fRF (MHz) CONVERSION GAIN vs. INPUT FREQUENCY 80 80 CONVERSION GAIN vs. INPUT FREQUENCY Conversion Gain, CG (dB) Conversion Gain, CG (dB) 60 VAGC = 4 V 60 VAGC = 4 V VAGC = 3 V 40 40 VAGC = 3 V VAGC = 1 V 20 VCC1 = 5 V, VCC2 = 5 V G1A-G1B : open 1 K load, TA = 25C 0 50 100 150 200 250 VAGC = 1 V 20 VCC1 = 5 V, VCC2 = 9 V G1A-G1B : open 1 K load, TA = 25C 0 50 100 150 200 250 0 0 Input Frequency, fRF (MHz) Input Frequency, fRF (MHz) UPC2798GR STANDARD CHARACTERISTICS (by measurement circuit 4: Total Block) THIRD ORDER INTERMODULATION LEVEL AND OUTPUT POWER vs. INPUT POWER 0 THIRD ORDER INTERMODULATION LEVEL AND OUTPUT POWER vs. INPUT POWER 0 Output Power, POUT (dBm) Output Power, POUT (dBm) POUT -20 POUT -20 IM3 IM3 -40 -40 -60 -80 -50 VCC1 = 5 V VCC2 = 5 V f1 = 44 MHz f2 = 46 MHz fOSC = 55 MHz POSC = -10 dBm G1A-G1B: short -40 -30 -20 -10 0 -60 -80 -50 VCC1 = 5 V VCC2 = 9 V f1 = 44 MHz f2 = 46 MHz fOSC = 55 MHz POSC = -10 dBm G1A-G1B: open -40 -30 -20 -10 0 Input Power, PIN (dBm) Input Power, PIN (dBm) THIRD ORDER INTERMODULATION LEVEL AND OUTPUT POWER vs. INPUT POWER 0 Output Power, POUT (dBm) POUT -20 IM3 -40 -60 -80 -50 VCC1 = 5 V VCC2 = 5 V f1 = 44 MHz f2 = 46 MHz fOSC = 55 MHz POSC = -10 dBm G1A-G1B: short -40 -30 -20 -10 0 Input Power, PIN (dBm) UPC2798GR STANDARD CHARACTERISTICS (by application circuit example : MIXER block) CONVERSION GAIN vs. INPUT FREQUENCY 30 NOISE FIGURE vs. AGC VOLTAGE 30 Conversion Gain, CG (dB) Noise Figure, NF (dB) VCC = 5.5 V 20 25 VCC = 5.0 V VCC = 4.5 V 10 20 30 fRF = 50 MHz fIF = 10 MHz PRF = -50 dBm VAGC = 4 V fRF = 50 MHZ fIF = 10 MHZ VCC = 4.5 V VCC = 5.0 V VCC = 5.5 V DSB 0 1 2 3 4 5 0 40 50 60 Input Frequency, fRF (MHz) AGC Voltage, VAGC (V) CONVERSION GAIN vs. AGC VOLTAGE 30 -10 -20 THIRD ORDER INTERMODULATION LEVEL AND OUTPUT POWER vs. INPUT POWER Conversion Gain, CG (dB) Output Power, POUT (dBm) fRF = 50 MHZ fIF = 10 MHZ PRF = -50 dBm VCC = 4.5 V VCC = 5.0 V 20 VCC = 5.5 V -30 -40 -50 POUT 10 IM3 -60 -70 -80 -90 VCC = 5 V fRF1 = 45 MHZ fRF2 = 46 MHZ fOSC= 55 MHZ VAGC= 0 V -50 -40 -30 -20 -10 0 10 0 -10 0 1 2 3 4 5 -100 -60 AGC Voltage, VAGC (V) Input Power, PIN (dBm) OSCILLATOR FREQUENCY vs. TUNING VOLTAGE 70 Oscillator Frequency, fOSC (MHz) 60 50 40 VCC = 5 V 30 0 5 10 15 20 Tuning Voltage, VTU (V) UPC2798GR PIN FUNCTIONS Pin No. 1 Pin Name AGC IN1 Pin Voltage Typ. (V) 1.5 Function and Explanation RF input pins. Pins 1 and 2 are each base inputs to a differential amplifier. In the case of a single-ended input, bypass the unused pin to ground through a capacitor. Equivalent Circuit 4 AGC Control 2 AGC IN2 1.5 1 2 Reg 3 VAGC 0~5 Gain control pin of the mixer input amplifier. VAGC up = gain up. It is recommended to use a 100k voltage divider at this pin. 4 AGC Control 3 4 VCC1 5.0 Supply voltage pin for the downconverter block. This pin should be connected with a bypass capacitor (e.g., 1000 pF) to minimize ground impedance. 5 OSC OUT 4.0 Output pin for the internal oscillator. This pin may be connected to the input of a PLL synthesizer. 4 5 REG 6 GND 0.0 Ground pin. This pin must be connected to system ground. Form ground pattern as wide as possible to minimize ground impedance. 7 OSC B2 2.4 Input pins for the internal oscillator. The internal oscillator consists of a balanced amplifier. 7 8 4 9 10 8 OSC C1 4.6 9 OSC C2 4.6 Reg Reg 10 OSC B1 2.4 UPC2798GR PIN FUNCTIONS Pin No. Pin Name Pin Voltage Typ. (V) ( ) is value at VCC = 9V 2.5 (4.7) Function and Explanation Equivalent Circuit 11 OUT2 Output pins for the video amplifier. With RL = 1k , the differential output voltage is 3 Vp-p. OUT1 and INA are in phase. OUT2 and INB are in phase. In the case of a single-ended output, bypass the unused pin to ground through a capacitor. 13 12 11 12 OUT1 2.5 (4.7) 13 VCC2 5~9 Supply voltage pin for the video amplifier block. This pin should be connected with a bypass capacitor (e.g., 1000 pF) to minimize ground impedance. Input pins for the video amplifier. These pins have high impedance. In the case of a single-ended input, bypass the unused pin to ground through a capacitor. 14 INB 2.5 (4.1) 17 15 13 14 16 15 INA 2.5 (4.1) 16 G1B 1.7 (3.3) Gain control pins for the video amplifier. The gain may be adjusted by varying the value of the resistor between pins 16 and 17. Maximum gain = short; Minimum gain = open. REG 17 G1A 1.7 (3.3) 18 MIX OUT1 3.7 Output pins for the downconverter. These are emitter follower outputs which feature low impedance. In the case of a single-ended output, bypass the unused pin to ground through a capacitor. 4 18 19 MIX OUT2 3.7 REG 19 20 GND 0.0 Ground pin. This pin must be connected to system ground. Form ground pattern as wide as possible to minimize ground impedance. UPC2798GR MEASUREMENT CIRCUIT 1 AGC & MIXER BLOCK 10nF 10nF AGC IN VAGC 220nF VCC 1 1nF OSC OUT 100k 100k 220nF 10nF 1 2 3 4 5 6 7 8 10nF OSC IN 9 10 20 19 18 17 16 15 14 13 12 11 50 10nF 10nF MIX OUT 10nF MEASUREMENT CIRCUIT 2 VIDEO AMP BLOCK RL = 1k 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 10nF 1k 10nF Signal 50 Generator 50 10nF 220nF Vcc 2 1nF 950 10nF 50 Spectrum Analyzer UPC2798GR MEASUREMENT CIRCUIT 3 VIDEO AMP BLOCK RL = 50 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 10nF Signal 50 Generator 50 10nF 220nF Vcc 2 1nF 950 50 10nF Spectrum Analyzer 10nF 50 MEASUREMENT CIRCUIT 4 TOTAL BLOCK 10nF 10nF AGC IN VAGC 220nF VCC 1 1nF OSC OUT 100k 100k 220nF 10nF 1 2 3 4 5 6 7 8 10nF OSC IN 9 10 20 19 18 17 16 15 14 13 12 11 10nF 1nF 10nF 10nF 10nF 220nF Vcc2 950 50 Spectrum Analyzer 1k 1k 5pF 10nF 1k UPC2798GR APPLICATION CIRCUIT EXAMPLE 10nF 10nF AGC IN VAGC 220nF VCC 1 1nF OSC OUT 10k Vtu Cv 1.2 H 10k 100k 100k 220nF 10nF 1000pF 10pF 20pF 10pF 1000pF 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 10nF 1nF 10nF 10nF 10nF 220nF Vcc2 OUT 1 OUT 2 1k 1k 5pF CV: ISV209 OUTLINE DIMENSIONS (Units in mm) PACKAGE OUTLINE SSOP 20 20 11 INTERNAL BLOCK DIAGRAM AGC IN1 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 GND MIX OUT 2 MIX OUT 1 G1A G1B VAMP IN1 VAMP IN2 VCC2 OUT1 OUT2 N NEC C2798G XXXXX 7.00 MAX 10 AGC IN2 VAGC VCC1 xxxxx = Lot/Date Code OSC OUT GND 1 6.40.2 4.40.1 1.00.1 OSC B2 OSC C2 OSC C2 OSC B1 1.5 0.1 1.8 MAX +0.10 0.22 - 0.05 +0.10 0.15- 0.05 0.50.2 0.65 0.575 MAX All dimensions are typical unless specified otherwise. ORDERING INFORMATION PART NUMBER UPC2798GR-E1-A Notes: Embossed tape, 12 mm wide. Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. EXCLUSIVE NORTH AMERICAN AGENT FOR RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES * Headquarters * 4590 Patrick Henry Drive * Santa Clara, CA 95054-1817 * (408) 988-3500 * Telex 34-6393 * FAX (408) 988-0279 24-Hour Fax-On-Demand: 800-390-3232 (U.S. and Canada only) * Internet: http://WWW.CEL.COM 6/99 DATA SUBJECT TO CHANGE WITHOUT NOTICE QUANTITY 2500/Reel 4-248 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix -A indicates that the device is Pb-free. The -AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL's understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL's liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability. 4-249 |
Price & Availability of UPC2798GR-E1-A
 |
|||||||||||||||||||||||||||||||||||||||||
|
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |
