 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HMC748LC3C v01.1208 13 Gbps, 2:1 SELECTOR w/ PROGRAMMABLE OUTPUT VOLTAGE & POSITIVE SUPPLY Typical Applications The HMC748LC3C is ideal for: * 2:1 Multiplexer up to 13 Gbps Features Supports High Data Rates: up to 13 Gbps Single-ended inputs Differential & Single-ended outputs Fast Rise and Fall Times: 22 / 22 ps Low Power Consumption: 250 mW typ. Programmable Differential Output Voltage Swing: 600 - 1200 mV Propagation Delay: 125 ps Single Supply: +3.3V 16 Lead Ceramic 3x3mm SMT Package: 9mm 2 7 HIGH SPEED LOGIC - SMT * RF ATE Applications * Broadband Test & Measurement * Serial Data Transmission up to 13 Gbps * Redundant Path Switching * Built-in Test Functional Diagram General Description The HMC748LC3C is a 2:1 Selector designed to support data transmission rates of up to 13 Gbps, and selector port operation of up to 13 GHz. The selector routes one of the two single-ended inputs to the differential output upon assertion of the proper select port. The HMC748LC3C also features an output level control pin, VR, which allows for loss compensation or for signal level optimization. All single-ended input signals to the HMC748LC3C are terminated with 50 ohms to Vcc on-chip, and may be either AC or DC coupled. The outputs of the HMC748LC3C may be operated either differentially or single-ended. Inputs or outputs can be connected directly to a 50 ohm to Vcc terminated system, while DC blocking capacitors may be used if the terminating system is 50 ohms to ground. The HMC748LC3C operates from a single +3.3V DC supply and is housed in a ceramic RoHS compliant 3x3 mm SMT package. Electrical Specifi cations, TA = +25C, Vcc = +3.3V Parameter Power Supply Voltage Power Supply Current Maximum Data Rate Maximum Select Rate Maximum Serial Transmission Rate Input High Voltage Input Low Voltage Input Return Loss Output Amplitude Differential, peak-to-peak Output High Voltage 1100 3.25 mVpp V Frequency <13 GHz Single-Ended, peak-to-peak 2.8 2.1 10 550 Conditions Min. 3.0 Typ. 3.3 76 13 13 26 3.8 3.3 Max 3.6 Units V mA Gbps GHz Gbps V V dB mVpp 7 - 170 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC748LC3C v01.1208 13 Gbps, 2:1 SELECTOR w/ PROGRAMMABLE OUTPUT VOLTAGE & POSITIVE SUPPLY Electrical Specifi cations (continued) Parameter Output Low Voltage Output Rise / Fall Time Output Return Loss Random Jitter, Jr Deterministic Jitter, Jd Propagation Delay, A or B to DOUT, td Propagation Delay Select to Data, tds Set Up & Hold Time, tSH Differential, 20% - 80% Frequency <13 GHz rms [1] peak-to-peak, 215 -1 PRBS input [2] 2 125 135 6 Conditions Min. Typ. 2 22 / 22 10 0.2 Max Units V ps dB ps rms ps, pp ps ps ps 7 HIGH SPEED LOGIC - SMT 7 - 171 [1] Upper limit of random jitter, Jr, determined by measuring and integrating output phase noise with a sinusoidal input at 5, 10, and 13.5 GHz over temperature [2] Deterministic jitter calculated by simultaneously measuring the jitter of a 200 mV, 12.5 GHz, 215 -1 PRBS input, and a single-ended output DC Current vs. Supply Voltage [1] [2] 110 +25C +85C -40C Output Differential vs. Supply Voltage [1] [2] 1200 DIFFERENTIAL VOLTAGE (mV) 1175 1150 1125 1100 1075 1050 1025 1000 2.9 3 3.1 3.2 3.3 3.4 3.5 3.6 3.7 +25C +85C -40C 100 DC CURRENT (mA) 90 80 70 60 2.9 3 3.1 3.2 3.3 3.4 3.5 3.6 3.7 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) Rise / Fall Time vs. Supply Voltage [1] [2] 25 23 RISE/FALL TIME (ps) 21 19 17 15 2.9 Output Differential vs. Frequency [1] 1300 OUTPUT DIFFERENTIAL (mV) 1200 1100 1000 900 800 700 600 tr tf 3 3.1 3.2 3.3 3.4 SUPPLY VOLTAGE (V) 3.5 3.6 3.7 2 4 6 8 10 12 14 16 18 FREQUENCY (GHz) [1] VR = +3.3V [2] Frequency = 13 GHz For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC748LC3C v01.1208 13 Gbps, 2:1 SELECTOR w/ PROGRAMMABLE OUTPUT VOLTAGE & POSITIVE SUPPLY Output Differential vs. VR [2] 1400 Rise / Fall Time vs. VR [2] 25 DIFFERENTIAL VOLTAGE (mV) 1200 RISE/FALL TIME (ps) 23 7 HIGH SPEED LOGIC - SMT 1000 21 800 +25C +85C -40C 19 tr tf 600 17 400 2.1 2.3 2.5 2.7 2.9 VR (V) 3.1 3.3 3.5 3.7 15 2.1 2.3 2.5 2.7 2.9 VR (V) 3.1 3.3 3.5 3.7 Input Return Loss vs. Frequency 0 -5 -10 RETURN LOSS (dB) -15 -20 -25 -30 -35 0 2 4 6 8 10 12 14 FREQUENCY (GHz) Output Return Loss vs. Frequency 0 -5 -10 RETURN LOSS (dB) -15 -20 -25 -30 -35 0 2 4 6 8 10 12 14 FREQUENCY (GHz) Select Port Return Loss vs. Frequency 0 -5 RETURN LOSS (dB) -10 -15 -20 -25 -30 0 2 4 6 8 10 12 14 FREQUENCY (GHz) [1] VR = +3.3V [2] Frequency = 13 GHz 7 - 172 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC748LC3C v01.1208 13 Gbps, 2:1 SELECTOR w/ PROGRAMMABLE OUTPUT VOLTAGE & POSITIVE SUPPLY Eye Diagram [1] Test Conditions: Waveform generated with an Agilent N4903A J-Bert. Rate = 13 GHz Eye Diagram data presented on a Tektronix CSA 8000 Device is AC coupled to scope. 7 HIGH SPEED LOGIC - SMT 7 - 173 Timing Diagram Truth Table Inputs SP L H H = Negative Voltage Level L = Positive Voltage Level Notes: D = DP - DN S = SP - SN SN H L Outputs DP A -> D B -> D For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC748LC3C v01.1208 13 Gbps, 2:1 SELECTOR w/ PROGRAMMABLE OUTPUT VOLTAGE & POSITIVE SUPPLY Absolute Maximum Ratings Power Supply Voltage (Vcc) Input Signals Output Signals -0.5V to +3.7V Vcc - 2V to Vcc + 0.5V +1V to +3.7V -65C to +150C -40C to +85C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 7 HIGH SPEED LOGIC - SMT Storage Temperature Operating Temperature Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: ALUMINA 2. LEAD AND GROUND PADDLE PLATING: 30-80 MICROINCHES GOLD OVER 50 MICROINCHES MINIMUM NICKEL. 3. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 4. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm DATUM -C6. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. 7. PADDLE MUST BE SOLDERED TO GND. 7 - 174 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC748LC3C v01.1208 13 Gbps, 2:1 SELECTOR w/ PROGRAMMABLE OUTPUT VOLTAGE & POSITIVE SUPPLY Pin Descriptions Pin Number 1, 4, 5, 8, 9, 12 Function GND Description Signal Grounds Interface Schematic 7 HIGH SPEED LOGIC - SMT 7 - 175 2, 3 AP, BP Data Inputs 6, 7 SP, SN Select Inputs 10, 11 DN, DP Data Outputs 13, 16 14, Package Base Vcc GND Positive Supply Supply Ground Output level control. Output level may be adjusted by applying a voltage to VR per "Output Differential vs. VR" plot. 15 VR For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC748LC3C v01.1208 13 Gbps, 2:1 SELECTOR w/ PROGRAMMABLE OUTPUT VOLTAGE & POSITIVE SUPPLY Evaluation PCB 7 HIGH SPEED LOGIC - SMT Item J1 J2 J3 J4 J5 J6 J7 J8 J9 Description AP BP SP SN DN DP GND VR Vcc List of Materials for Evaluation PCB 122517 [1] Item J1 - J6 J7 - J9 JP1 C1, C2 C3 - C5 R2 U1 PCB [2] Description PCB Mount SMA RF Connectors DC Pin Shorting Jumper 4.7 F Capacitor, Tantalum 100 pF Capacitor, 0402 Pkg. 10 Ohm Resistor, 0603 Pkg. HMC748LC3C High Speed Logic, 2:1 Selector 122515 Evaluation Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown. The exposed package base should be connected to GND. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. 7 - 176 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC748LC3C v01.1208 13 Gbps, 2:1 SELECTOR w/ PROGRAMMABLE OUTPUT VOLTAGE & POSITIVE SUPPLY Application Circuit 7 HIGH SPEED LOGIC - SMT For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 177 |
Price & Availability of HMC748LC3C
 |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |
