Part Number Hot Search : 
MT5100 HC908 T89C2051 TDA8925 2SK3025 1380TL MK316B AT5562
Product Description
Full Text Search
 

To Download HDBF07006B64 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
  SPEC NO :
SPECIFICATION
CUSTOMER PRODUCT MODEL NO PREPARED APPROVED CHARLES
SAW FILTER HDBF07006B64
CHECKED Houshihong D A T E 2007-01-25
CUSTOMER RECEIVED:
CHECKED
APPROVED
DATE
Shoulder Electronics Limited
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 1 of 6
SAW FILTER
HDBF07006B64
History Record
Date Spec No Part No Customer No Modify Content Remark
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 2 of 6
SAW FILTER 1. SCOPE
HDBF07006B64
This specification shall cover the characteristics of SAW filter BF07006B64
2. ELECTRICAL SPECIFICATION
DC Voltage VDC AC Voltage Vpp Operation temperature Storage temperature RF Power Dissipation 10V 10V50Hz/60Hz -10 to +60 -40 to +85 0dBm
Electronic Characteristics Fo = 70.0 MHz Terminating source impedance: 50 ohm and matching network Terminating load impedance: 50 ohm and matching network Minimum Typical Center Frequency Insertion Loss 3dB Bandwidth 35dB Bandwidth 45dB Bandwidth Passband variation Ultimate Rejection( f05MHz) Absolute Delay MHz dB MHz MHz MHz dB dB usec 69.95 6.0 45 70.0 21.80 6.09 6.68 6.75 0.9 50 3.95 Maximum 70.05 24.0 6.8 7.2 1.0 4
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 3 of 6
SAW FILTER 3. DIMENSION
HDBF07006B64
4.TEST CIRCUIT
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 4 of 6
SAW FILTER 5. ENVIRONMENTAL CHARACTERISTICS
HDBF07006B64
5-1 High temperature exposure Subject the device to +85 for 16 hours. Then release the filter into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in table 1. 5-2 Low temperature exposure Subject the device to -20 for 16 hours. Then release the device into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in table 1. 5-3 Temperature cycling Subject the device to a low temperature of -40for 30 minutes. Following by a high temperature of +80 for 30 Minutes. Then release the device into the room conditions for 24 hours prior to the measurement. It shall meet the specifications in table 1. 5-4 Resistance to solder heat Dip the device terminals no closer than 1.5mm into the solder bath at 260 10 for 101 sec. Then release the device into the room conditions for 4 hours. The device shall meet the specifications in table 1. 5-5 Solderability Subject the device terminals into the solder bath at 245 5 for 5s, More than 95% area of the terminals must be covered with new solder. It shall meet the specifications in table 1. 5-6 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall fulfill the specifications in table 1. 5-7 Vibration Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 Hz. The device shall fulfill the specifications in table 1. 5-8 Lead fatigue 5-8-1 Pulling test Weight along with the direction of lead without an shock 1kg. The device shall satisfy all the initial Characteristics. 5-8-2 Bending test Lead shall be subject to withstand against 90 bending with 450g weight in the direction of thickness. This operation shall be done toward both direction. The device shall show no evidence of damage and shall satisfy all the initial electrical characteristics.
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 5 of 6
SAW FILTER 6.Typical frequency response
HDBF07006B64
7. REMARK
7.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 7.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 7.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component.
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 6 of 6


▲Up To Search▲   

 
Price & Availability of HDBF07006B64

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X