 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HMJ7-1 High Dynamic Range FET Mixer Product Features * Greater than +34 dBm IIP3 * 77 dBc 2x1 Spur Rejection in IF Band * RF 1000 - 2000 MHz * LO 1000 - 2000 MHz * IF 10 - 1000 MHz * +24 dBm LO Drive Level * +5V Bias (40 mA) * SMT J-Lead Package Product Description The HMJ7-1 is a high dynamic range GaAs FET mixer. This active broadband mixer realizes a typical third order intercept point of +34 dBm at an LO drive level of +21 dBm. The HMJ7-1 also provides excellent suppression of spurious intermodulation products, greater than 67 dBc, meeting DOCSIS2 and Euro DOCSIS system requirements. The HMJ7-1 is a specially screened version of the HMJ7 mixer meeting all of the performance requirements of the HMJ7 with 21 dBm LO power, but also meeting the suppression requirements for intermodulation products at a 24 dBm LO power level. The HMJ7-1 comes in a low cost, 22-pin J-Lead package. The combination of high dynamic range and spurious suppression makes the HMJ7-1 an ideal choice for CATV headend transmission equipment and other applications requiring a broadband mixer in the 1000 MHz to 2000 MHz frequency range. Functional Diagram RF LO +5Vdc IF Applications * CATV Head-End Equipment Function IF LO RF +5V Ground Pin No. 2 13 21 10 All other pins Specifications (1) Parameter RF Frequency Range LO Frequency Range IF Frequency Range SSB Conversion Loss Noise Figure LO-RF Isolation LO-IF Isolation RF-IF Isolation Input IP3 RF Return Loss LO Return Loss IF Return Loss Spurious Rejection (2) Spurious Rejection (2) Input P1dB LO Drive Level DC Current at +5V Bias Units MHz MHz MHz dB dB dB dB dB dBm dB dB dB dBc dBc dBm dBm mA Min Typ 1000 - 2000 1000 - 2000 10 - 1000 8.5 10.5 24 30 24 34 10 5 14 77 77 +23 +21 40 Max Condition 9.5 21 24 29 RF = 1018 MHz @ 0 dBm 67 76 LO = +24 dBm, IF freq = 150 - 540 MHz, 640 - 1000 MHz LO = +24 dBm, IF freq = 540 - 640 MHz 60 1. Test conditions unless otherwise noted: 25 C, RF = 1018.75 MHz @ 0 dBm, LO = 21 dBm, IF = 50, 650, 860 MHz in a high-side LO configuration. 2. The 2x1 spur is tested where the IM spur = 2 * RF input - LO, where RF input = 1090 MHz @ -14 dBm, LO = 1190 to 2090 MHz @ 24 dBm, IM spur = output frequency. The IM spur level is specified in dBc with respect to the desired IF frequency calculated: IF output = LO - RF input. Absolute Maximum Rating Parameters Operating Case Temperature Storage Temperature Maximum Input Power Ordering Information Part No. HMJ7-1 Rating -40 to +85 C -65 to +100 C +25 dBm Description High Dynamic Range FET Mixer Operation of this device above any of these parameters may cause permanent damage. Specifications and information are subject to change without notice TriQuint Semiconductor, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6633 * e-mail: info-sales@tqs.com * Web site: www. TriQuint.com January 2009 HMJ7-1 High Dynamic Range FET Mixer Typical Performance Data All measurements are shown with a LO drive level = +21 dBm. Improved performance is expected with LO = +24 dBm. Specifications and information are subject to change without notice TriQuint Semiconductor, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6633 * e-mail: info-sales@tqs.com * Web site: www. TriQuint.com January 2009 HMJ7-1 High Dynamic Range FET Mixer Outline Drawing Product Marking The component will be marked with an "HMJ7" designator with a four-digit alphanumeric lot number XXXX. Tape and reel specifications for this part are located on the website in the "Application Notes" section. ESD Information ESD Rating: Value: Test: Standard: ESD Rating: Value: Test: Standard: Class 2 Passes at 2000 V Human Body Model (HBM) JEDEC Standard JESD22-A114 Class IV Passes at 2000 V Charged Device Model (CDM) JEDEC Standard JESD22-C101 Dimensions are expressed in Inches. TOLERANCE .XXX [ .015 .XX [ .02 Drawing is illustrated at Max dimensions. Mounting Config. Notes Land Pattern / Mounting Configuration 1. Ground vias are critical for thermal and RF grounding considerations. 2. A minimum of 36 ground vias are required for 14 mil FR4 boards. 3. If your PCB design rules allow, ground vias should be placed under the land pattern for better RF performance. Otherwise ground vias should be placed as close to the land pattern as possible. 4. Trace width depends on the PCB material. Specifications and information are subject to change without notice TriQuint Semiconductor, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6633 * e-mail: info-sales@tqs.com * Web site: www. TriQuint.com January 2009 |
Price & Availability of HMJ7
 |
|||||||||||||||||||||
|
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |
