View B150XG02V4_1572561.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

product specification b150xg02 v4 product s p ecification 15.0? xga color tft -lcd module model name: b150xg02 v4 ( ) preliminary s p ecifications (v) final s p ecifications note: this s p ecification is subject to change w i thout notice. d o c u m e n t v e r s i o n 0 . 3 2 / 3 7 www..net
product specification b150xg02 v4 contents 1. handling precautions ......................................................................................... 5 2. general description ............................................................................................ 5 2.1 display characteristics ...................................................................................................... 6 2.2 optical characteristics ....................................................................................................... 7 3. functional block diagram ................................................................................ 12 4. absolute maximum ratings ............................................................................. 13 4.1 absolute ratings of tft lcd module .............................................................................. 13 4.2 absolute ratings of backlight unit ................................................................................... 13 4.3 absolute ratings of environment ..................................................................................... 13 5. electrical characteristics .................................................................................. 14 5.1 tft lcd module .............................................................................................................. 14 5.2 backlight unit ................................................................................................................... 17 6. signal characteristic ........................................................................................ 19 6.1 pixel format image .......................................................................................................... 19 6.2 the input dat a format ....................................................................................................... 20 6.3 signal description ............................................................................................................ 21 6.4 interface t i ming ............................................................................................................... 23 7. connector & pin assignment .......................................................................... 25 7.1 tft lcd module .............................................................................................................. 25 7.2 backlight unit ................................................................................................................... 25 7.3 signal for lamp connector ............................................................................................... 25 8. vibration and shock test ................................................................................. 26 8.1 v i bration t e st ................................................................................................................... 26 8.2 shock t e st s pec: ............................................................................................................. 26 9. reliability ........................................................................................................... 27 10. mechanical characteristics ............................................................................ 28 10.1 lcm outline dimension ................................................................................................. 28 10.2 screw hole depth and center position .......................................................................... 29 1 1 .1 shipping label format ................................................................................................... 30 1 1 .2. carton p a ckage ............................................................................................................. 31 1 1 .3 shipping p a ckage of p a lletizing sequence ..................................................................... 32 12. appendix: edid description ........................................................................... 33 d o c u m e n t v e r s i o n 0 . 3 3 / 3 7 www..net
product specification b150xg02 v4 record of revision v e rsion and date page old description n e w d e s c r i p t i o n r e m a r k 0.1 2005/05/23 all first edition for customer 0.2 2005/06/9 10 add note 5 and note 6 0.3 2005/07/19 16 add description in 5.1.2 f i n a l d o c u m e n t v e r s i o n 0 . 3 4 / 3 7 www..net
document version 0.3 5/37 product specification b150xg02 v4 1. handling precautions 1) since front polarizer is easily dam aged, pay attention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long cont act with water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break or cra ck if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at t he back of the module to any directions. 9) in case if a module has to be put back into the packing container slot after once it was taken out from the container, do not pre ss the center of the ccfl reflector edge. instead, press at the far ends of the cfl reflector edge softly. otherwise the tft module may be damaged. 10) at the insertion or remova l of the signal interface connecto r, be sure not to rotate nor tilt the interface connector of the tft module. 11) after installation of the tft module in to an enclosure (notebook pc bezel, for example), do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consider ation that no bending/twisting forces are applied to the tft module from outside. otherwise the tft module may be damaged. 12) cold cathode fluorescent lamp in lcd cont ains a small amount of mercury. please follow local ordinances or regulations for disposal. 13) small amount of materials having no flammab ility grade is used in the lcd module. the lcd module should be supplied by power complied wit h requirements of limited power source(, iec60950 or ul1950), or be applied exemption. 14) the lcd module is designed so that the cf l in it is supplied by limited current circuit(iec60950 or ul1950). do not connect the cfl in hazardous voltage circuit. 2. general description b150xg02 v4 is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and backlight system. the screen fo rmat is intended to support the xga (1024(h) www..net
document version 0.3 6/37 product specification b150xg02 v4 x 768(v)) screen and 262k colors (rgb 6-bits data driver). all i nput signals are lvds interface compatible. inverter card of backlight is not included. b150xg02 v4 is designed for a display unit of notebook style personal computer and industrial machine. 2.1 display characteristics the following items are characteri stics summary on the table under 25
condition: items unit specifications screen diagonal [mm] 381 (15.0?) active area [mm] 304.1 x 228.1 pixels h x v 1024x3(rgb) x 768 pixel pitch [mm] 0.297x0.297 pixel arrangement r.g.b. vertical stripe display mode normally white typical white luminance (icfl=6.0ma) [cd/m 2 ] 170 typ. (5 points average) 150 min. (5 points average) (note1) luminance uniformity 1.25 max. (5 points) contrast ratio 300 typ. optical rise time/fall time [msec] 16/9 typ. nominal input voltage vdd [volt] +3.3 typ. typical power consumption [watt] 5.6w max. weight [grams] 585g typ. physical size [mm] 317.3(typ. )x 242.0(typ.) x 6.5(max.) electrical interface 1 channel lvds surface treatment anti-glare, harness 3h, haze 25%, reflectance 4.3% support color native 262k colors ( rgb 6-bit data driver ) temperature range operating storage (non-operating) [ o c] [ o c] 0 to +50 -20 to +60 rohs compliance rohs compliance www..net
document version 0.3 7/37 product specification b150xg02 v4 2.2 optical characteristics the optical characteristics are m easured under stable conditions at 25
(room temperature): item unit conditions min. typ. max. note white luminance ccfl 6.0ma [cd/m2] 5 points average 150 170 - 1,2,3 [degree] [degree] horizontal (right) cr = 10 (left) - - 40 40 - - viewing angle [degree] [degree] vertical (upper) cr = 10 (lower) - - 10 30 - - 2,7 uniformity 5 points 1.25 uniformity 13 points 1.50 1 cr: contrast ratio 250 300 - 6 cross talk % 4 4 [msec] rising - 16 24 [msec] falling - 9 11 response time [msec] raising + falling 25 35 5 red x 0.560 0.580 0.600 red y 0.320 0.340 0.360 green x 0.290 0.310 0.330 green y 0.530 0.550 0.570 blue x 0.135 0.155 0.175 blue y 0.135 0.155 0.175 white x 0.293 0.313 0.333 color / chromaticity coordinates (cie 1931) white y 0.309 0.329 0.349 2,7 www..net
product specification b150xg02 v4 note 1: 5 points position (display area : 304.5mm x 228.375mm) 1 2 3 4 5 h/4 h/4 h/4 h/4 h w w/ 4 w/4 w/4 w/ 4 note 2: 13 points position w/ 4 w w/ 4 h h/ 4 h/ 4 h/ 4 h/ 4 7 9 10 w/ 4 1 8 w/ 4 10 10 10 10 2 3 13 12 4 5 6 11 note 3: the luminance uniformity of 5 and 13 points is defined by dividing the maximum luminance values by the minimum test point luminance maximum brightness of five points ? w5 = minimum brightness of five points ? w 13 = minimum brightness of thirteen points maximum brightness of thirteen points d o c u m e n t v e r s i o n 0 . 3 8 / 3 7 www..net
product specification b150xg02 v4 note 4: measurement method the lcd module should be stabilized at given temperatur e for 30 minutes to avoid abrupt temperature change during measuring. in order to stabilize the luminance, t he measurement should be executed after lighting backlight for 30 minutes in a stable, windless and dark room. photo detector tft - lcd m odule lcd p anel field=2 50 cm center of the screen note 5 j definition of average luminance of white (y l ): measure the luminance of gray level 63 at 5 points d y l = [l (1)+ l (2)+ l (3)+ l (4)+ l (5)] / 5 l (x) is corresponding to the luminance of the point x at figure in note (1). note 6 j definition of contrast ratio: contrast ratio is calculated with the following formula. bri g htness on the ?white? state contrast ratio ( cr ) = bri g htness on the ?black? state d o c u m e n t v e r s i o n 0 . 3 9 / 3 7 www..net
product specification b150xg02 v4 note 7 j definition of cross talk (ct) ct = | y b ? y a | / y a 100 (%) where y a = luminance of measured location without gray level 0 pattern (cd/m 2 ) y b = luminance of measured location with gray level 0 pattern (cd/m 2 ) note 8: definition of response time: the output signals of bm-7 or equivalent are measur ed when the input signals are changed from ?black? to ?white? (falling time) and from ?white? to ?black? (rising ti me), respectively. the response time interval between the 10% and 90% of amplitudes. refer to figure as below. "black" tr tf "whit e" "white" 0% % % 100% s i g n a l ( r e l a t i v e v a l u e ) 10 90 d o c u m e n t v e r s i o n 0 . 3 1 0 / 3 7 www..net
d o c u m e n t v e r s i o n 0 . 3 1 1 / 3 7 product specification b150xg02 v4 note 9. definition of viewing angle viewing angle is the measurement of contrast ratio 10, at the screen center, over a 180 horizontal and 180 vertical range (off-normal viewing angles). the 180 viewing angle range is broken down as follows; 90 ( ) horizontal left and right and 90 ( ) vertical, high (up) and low (down). t he measurement direction is typically perpendicular to the display surface with the scr een rotated about its center to develop the desired measurement viewing angle. www..net
product specification b150xg02 v4 3. functional block diagram the following diagram shows the functional blo ck of the 15.0 inches wide color tft/lcd module: tft a rra y / cell 6b it color dat a for r / g / b hs y n c vs y n c v dd lc d c o ntro ller lcd dr i v e car d bac k l i g ht uni t 1024(r/g / b) x 3 gnd dc - d c c o nv er ter re f c i r c u i t y -d ri v e r x-d r i v e r dspt mg (3 p a ir s l v d s ) dt c l k ( 1 p a ir l v d s ) ja e ja e fi - x b30sl- h f 10 mat i ng t y pe ja e fi - s 30m lcd con nec t o r jst bhs r - 0 2 vs- 1 ma t i n g t yp e s m 02b - b h ss - 1 lam p c o nnec t o r d o c u m e n t v e r s i o n 0 . 3 1 2 / 3 7 www..net
product specification b150xg02 v4 4. absolute maximum ratings absolute maximum ratings of the module is as following: 4.1 absolute ratings of tft lcd module i t e m s y m b o l m i n m a x u n i t conditions logic/lcd drive v i n - 0 . 3 + 4 . 0 [ v o l t ] note 1,2 4.2 absolute ratings of backlight unit i t e m s y m b o l m i n m a x u n i t conditions ccfl current icfl - 7.0 [ma] rms note 1,2 4.3 absolute ratings of environment i t e m s y m b o l m i n m a x u n i t conditions operating temperature top 0 +50 [ o c ] n o t e 3 operation humidity hop 5 95 [%rh] note 3 storage temperature tst -20 +60 [ o c] n o t e 3 storage humidity hst 5 9 5 [% rh] note 3 note 1: with in ta (25
) note 2: permanent damage to the device may occur if exceed maximum values note 3: for quality perfermance, please refe r to auo iis(incoming inspection standard). d o c u m e n t v e r s i o n 0 . 3 1 3 / 3 7 www..net
product specification b150xg02 v4 tw b=3 9 c operating range storage range 5. electrical characteristics 5.1 tft lcd module 5.1.1 pow e r specification input power specificat ions are as follows; sy m b l e p a r a m e t e r min t y p max u nits c o n d i t i o n v d d l o g i c / l c d d r i v e volta g e 3 . 0 3 . 3 3 . 6 [ v o l t ] load c a p a c i t a n c e 20uf p d d vdd p o w e r 1 . 1 1 . 4 [ w a t t ] black pattern i d d i d d c u r r e n t 3 8 0 4 2 0 m a black pattern i rush i n r u s h c u r r e n t tbd m a v d d r p a l l o w a b l e logic/lcd drive ripple voltage 1 0 0 [ m v ] p-p note 1 : measurement conditions: d o c u m e n t v e r s i o n 0 . 3 1 4 / 3 7 www..net
product specification b150xg02 v4 +5.0v +12.0v vcc r1 47k r2 1k vr1 47k sw1 sw mag-spst 1 2 f1 q3 ao6402 g d2 s d1 d5 d6 c1 1uf/16v q3 ao6402 g d2 s d1 d5 d6 c3 0.01uf/25v c2 1uf/25v (high to low) control signal (lcd module input) 3.3v 90% 0.5ms 10% 0v vin rising time d o c u m e n t v e r s i o n 0 . 3 1 5 / 3 7 www..net
product specification b150xg02 v4 5.1.2 signal electrical characteristics input signals shall be low or hi-z state when vdd is off. it is recommended to refer the specifications of thc63lvdf84a(thine electronics inc.) in detail. signal electrical characteristics are as follows; p a r a m e t e r c o n d i t i o n m i n m a x u n i t vth differential input high threshold (vcm=+1.2v) 100 [mv] vtl differential input low threshold (vcm=+1.2v) -100 [mv] vcm differential input common mode voltage 1.125 1.375 [v] note: lvds signal waveform v ss vcm vtl vth d o c u m e n t v e r s i o n 0 . 3 1 6 / 3 7 www..net
document version 0.3 17/37 product specification b150xg02 v4 5.2 backlight unit parameter guideline for ccfl inverter parameter min typ max units condition white luminance 5 points average - 170 - [cd/m 2 ] (ta = 25
) ccfl current(icfl) - 6.0 7.0 [ma] rms (ta=25
) note 2 ccfl frequency(fcfl) 50 - 60 [khz] (ta=25
) note 3,4 ccfl ignition voltage(vs) 1560 - - [volt] rms (ta= 0
) note 5 ccfl voltage (reference) (vcfl) 585 650 715 [volt] rms (ta=25
) note 6 ccfl power consumption (pcfl) - 3.9 5 [watt] (ta=25
) note 6 note 1: typ are auo recommended design points. *1 all of characteristics listed are measured under the condition using the auo test inverter. *2 in case of using an inverter other than listed, it is recommended to check the inverter carefully. sometimes, interfering noise stripes appear on the screen, and s ubstandard luminance or flicker at low power may happen. *3 in designing an inverter, it is suggested to check safety circuit very carefully. impedance of cfl, for instance, becomes more than 1 [m ohm] when cfl is damaged. *4 generally, cfl has some amount of delay time after applying kick-off voltage. it is recommended to keep on applying kick-off voltage for 1 [sec] until discharge. *5 cfl discharge frequency must be carefully chosen so as not to produce interfering noise stripes on the screen. *6 reducing cfl current increases cfl discharge voltage and generally increases cfl discharge frequency. so all the parameters of an inverter should be care fully designed so as not to produce too much leakage current from high-voltage output of the inverter. note 2: it should be employed the inverter which has ?duty dimming?, if icfl is less than 4ma. note 3: cfl discharge frequency should be carefully det ermined to avoid interference between inverter and tft lcd. note 4: the frequency range will not affect to lamp life and reliability characteristics. www..net
product specification b150xg02 v4 note 5: cfl inverter should be able to give out a pow er that has a generating capac ity of over 1,560 voltage. lamp unit needs 1,560 voltage minimum for ignition. note 6: calculator value for reference (icflvcfl=pcfl) note 7: requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp, are following. it shall help increase the lamp lifetime and reduce leakage current. a. the asymmetry rate of the inverter waveform should be less than 10%. b. the distortion rate of the waveform should be within ? 2 ? 10%. * inverter output waveform had better be more similar to ideal sine wave. d o c u m e n t v e r s i o n 0 . 3 1 8 / 3 7 www..net
d o c u m e n t v e r s i o n 0 . 3 1 9 / 3 7 product specification b150xg02 v4 6. signal characteristic 6.1 pixel format image following figure shows the relationship of the input signals and lcd pixel format. r g b r g b r g b r g b r g b r g b r g b r g b 0 1 1022 1023 1s t l i n e 768th lin e www..net
d o c u m e n t v e r s i o n 0 . 3 2 0 / 3 7 product specification b150xg02 v4 6.2 the input data format signal name description red5 red4 red3 red2 red1 red0 red data 5 (msb) red data 4 red data 3 red data 2 red data 1 red data 0 (lsb) red-pixel data red-pixel data each red pixel's brightness data consists of these 6 bits pixel data. green 5 green 4 green 3 green 2 green 1 green 0 green data 5 (msb) green data 4 green data 3 green data 2 green data 1 green data 0 (lsb) green-pixel data green-pixel data each green pixel's brightness data consists of these 6 bits pixel data. blue 5 blue 4 blue 3 blue 2 blue 1 blue 0 blue data 5 (msb) blue data 4 blue data 3 blue data 2 blue data 1 blue data 0 (lsb) blue-pixel data blue-pixel data each blue pixel's brightness data consists of these 6 bits pixel data. d t c l k data clock the typical frequency is 68.9 mhz.. the s i g n a l is used to strobe the pixel data and dsptmg signals. all pixel data shall be valid at the falling edge when the dsptmg signal is high. dsptmg display timing this signal is strobed at the falling edge of -dtclk. when the signal is high, the pixel data shall be valid to be displayed. vsync vertical sync the signal is synchronized to -dtclk . hsync horizontal sync the signal is synchronized to -dtclk . note: output signals from any system sha ll be low or hi-z state when vdd is off. www..net
document version 0.3 21/37 product specification b150xg02 v4 6.3 signal description the lvds receiver equipped in this lcd module is compat ible with sn75lvds86 standard. lvds is a differential signal technology for lcd interface and high speed data transfer device. transmitter shall be sn75lvds84 (negative edge sampling) or compatible . pin# signal name description 1 gnd ground 2 vdd +3.3v power supply 3 vdd +3.3v power supply 4 v edid +3.3v edid power 5 nc no connection (for auo test) 6 clk edid edid clock input 7 data edid edid data input 8 rxin0- lvds differential data input(red0-red5, green0) 9 rxin0+ lvds differential data input(red0-red5, green0) 10 gnd ground 11 rxin1- lvds differential data input(green1-green5, blue0-blue1) 12 rxin1+ lvds differential data input(green1-green5, blue0-blue1) 13 gnd ground 14 rxin2- lvds differential data input(blue2- blue5, hsync, vsync, dsptmg) 15 rxin2+ lvds differential data input(blue2- blue5, hsync, vsync, dsptmg) 16 gnd ground 17 rxclkin- lvds differential clock input 18 rxclkin+ lvds differential clock input 19 gnd ground 20 gnd ground 21 nc no connection (for auo test) 22 nc no connection (for auo test) 23 nc no connection (for auo test) 24 nc no connection (for auo test) 25 nc no connection (for auo test) 26 nc no connection (for auo test) 27 nc no connection (for auo test) 28 nc no connection (for auo test) 29 nc no connection (for auo test) 30 nc no connection (for auo test) www..net
d o c u m e n t v e r s i o n 0 . 3 2 2 / 3 7 b150xg02 v4 product specification note1: start from right side connector 30 1 n c g n d note2: please follow pswg. note3: input signals shall be low or hi-z state when vdd is off. internal circuit of lvds inputs are as following. the module uses a 100ohm resistor between positiv e and negative data lines of each receiver input r r r r s n 75 l v d s 86 or c o m p at i b l e si g n al i nput pi n n o . 9 11 12 14 15 17 18 8 rx i n 0 + rx i n 0 - rx i n 1 + rx i n 1 - rx i n 2 + rx i n 2 - r x cl ki n + rx c l ki n- www..net
d o c u m e n t v e r s i o n 0 . 3 2 3 / 3 7 product specification b150xg02 v4 6.4 interface timing 6.4.1 timing characteristics basically, interface timings should match the 1024x768 /60hz manufacturing guide line timing. p a r a m e t e r s y m b o l m i n . ty p . m a x . u n i t frame rate - 55 60 - hz clock frequency 1/ t clock 5 0 6 5 6 8 m h z p e r i o d t v 7 7 4 8 0 6 1 0 2 4 ac t i v e t vd - 7 6 8 - vertic al section b l a n k i n g t vb 6 3 8 2 5 6 t line p e r i o d t h 1 0 5 4 1 3 4 4 1 6 4 8 ac t i v e t hd - 1 0 2 4 - horizontal section b l a n k i n g t hb 3 0 3 2 0 6 2 4 t clock end-frame checking period tef 2 t h de checking period tde 4 t h note : de mode only 6.4.2 timing diagram dotc lk de t h t hb t hd de t v t vb t vd inp u t tim i n g d e finiti o n ( d e m o d e ) t cl ock inpu t da t a pi x e l 1 pi xel 2 pi xe l 3 pi xel n- 1 pi x e l n inva i l d da t a inva i l d da t a pi xe l 1 www..net
d o c u m e n t v e r s i o n 0 . 3 2 4 / 3 7 product specification b150xg02 v4 6.5 power on/off sequence vdd power and lamp on/off sequence is as follows. interface signals are also shown in the chart. signals from any system shall be hi-z st ate or low level when vdd is off. t4 t3 t2 t5 valid data t1 10% 90% 10% 90% t7 t6 power supply vdd lvds inter fac e backlight on pow e r sequence timing value parameter min. ty p. max. units t1 0.5 - 10 (ms) t2 0 - 50 (ms) t3 0 - 50 (ms) t4 400 - - (ms) t5 200 - - (ms) t6 200 - - (ms) t7 0 - 10 (ms) www..net
document version 0.3 25/37 product specification b150xg02 v4 7. connector & pin assignment physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. 7.1 tft lcd module connector name / designation for signal connector manufacturer jae or compatible type / part number fi-xb 30sl-hf10 or compatible mating housing/part number fi-x30m, fi-x30c or fi-x30h 7.2 backlight unit physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. connector name / designation for lamp connector manufacturer jst type / part number bhsr-02vs-1 mating type / part number sm02b-bhss-1-tb 7.3 signal for lamp connector pin # cable color signal name 1 red lamp high voltage 2 white lamp low voltage www..net
d o c u m e n t v e r s i o n 0 . 3 2 6 / 3 7 product specification b150xg02 v4 8. vibration and shock test 8.1 vibration test test spec: test method: non-operation acceleration: 1.5g frequency: 10 - 500hz random sweep: 30 minutes each axis (x, y, z) 8.2 shock test spec: test spec: test method: non-operation acceleration: 220 g , half sine wave ac tive time: 2 ms pulse: x,y,z .one time for each side www..net
document version 0.3 27/37 product specification b150xg02 v4 9. reliability items required condition note temperature humidity bias 40
/90%,300hr high temperature operation 50
/dry,300hr low temperature operation 0
,300hr on/off test 25
,150hrs(on/10 sec. off/10sec., 10,000 cycles) hot storage 60
/35% rh ,250 hours cold storage -20
/50% rh ,250 hours thermal shock test -20
/30 min ,60
/30 min 100cycles hot start test 50
/1 hr min. power on/off per 5 minutes, 5 times cold start test 0
/1 hr min. power on/off per 5 minutes, 5 times shock test (non-operating) 220g, 2ms, half-sine wave vibration test (non-operating) random vibration, 1.5 g zero-to-peak, 10 to 500 hz, 30 mins in each of three mutually perpendicular axes. esd contact : ? 8kv/ operation air : ?15kv / operation note 1 room temperature test 25
, 2000hours, operating with loop pattern note1: according to en61000-4-2 , esd class b: some performance degradation allowed. no data lost . self-recoverable. no hardware failures. note2: ccfl life time: 10,000 hours minimum under normal module usage. note3: mtbf (excluding the ccfl) : 30,000 hours with a confidence level 90% www..net
d o c u m e n t v e r s i o n 0 . 1 2 8 / 3 7 b150xg02 v4 product specification 10. mechanical characteristics 10.1 lcm outline dimension www..net
d o c u m e n t v e r s i o n 0 . 1 2 9 / 3 7 b150xg02 v4 product specification 10.2 screw hole depth and center position screw hole minimum depth, from side surface =2.5 mm (see drawing) screw hole center location, from front surface = 3.1 0.3mm (see drawing) screw torque: maximum 2.5 kgf-cm www..net
d o c u m e n t v e r s i o n 0 . 1 3 0 / 3 7 b150xg02 v4 product specification 11.1 shipping label format b150xg02 v4 05/20 0axx x *xxxxxxxxxxxx- xxxxx 0a firmw a re 88mm week code 1 control code manufacturing area model name 16mm hardw a re note 1: ic combination control code h/w sourc e ic: mec mnf816bg-rd gate ic: tsb jbt6la2-as oaxxx oa source nt 3960g gate ic: nt 3955 1axxx 1a www..net
d o c u m e n t v e r s i o n 0 . 1 3 1 / 3 7 b150xg02 v4 product specification 11.2. carton package the outside dimension of carton is 480 (l)mm x 390 (w)mm x 340 (h)mm vtf 'ps nb sl 1bofm $vt i jpo 5pq tj ef $v t i j p o $b s u p o qptjujpo $bsupo mb cf m ) ubqjohdmptf www..net
d o c u m e n t v e r s i o n 0 . 1 3 2 / 3 7 b150xg02 v4 product specification 11.3 shipping package of palletizing sequence 5 p q d b s e cpbs e 8 p pefo qbm m f u # p u u pn d bs ecpbs e $ p s o fs b ohm f 4 u sfud i g j mn 1& c b o e / p u f - j n j u p g cpy qbm m fu j [ j oh . b y m b zfs t t ij q boe t u pdl d p oej u j po t
www..net
d o c u m e n t v e r s i o n 0 . 1 3 3 / 3 7 b150xg02 v4 product specification 12. appendix: edid description a ddress f unct i o n value value value notes hex hex bi n d e c d a t e : a p r/ 11/ 2 0 0 5 00 header 00 00000000 0 01 ff 11111111 255 02 ff 11111111 255 03 ff 11111111 255 04 ff 11111111 255 05 ff 11111111 255 06 ff 11111111 255 07 00 00000000 0 08 eisa manuf. code lsb 06 00000110 6 ascii data string:b150xg02 09 compressed ascii af 10101111 1 7 5 a u o 0a panel size, resolution 51 01010001 8 1 1 5 ? x g a 0b model number, version 24 00100100 3 6 0 2 v 4 0c 00 00000000 0 f i x e d n u m b e r 0d 00 00000000 0 f i x e d n u m b e r 0e 00 00000000 0 f i x e d n u m b e r 0f 00 00000000 0 f i x e d n u m b e r 10 w eek of manufacture 01 00000001 1 w e e k 0 1 11 year of manufacture 0f 00001111 1 5 1 5 ( 2 0 0 5 - 1 9 9 0 = 1 5 ) 12 edid structure ver. 01 00000001 1 13 edid revision # 03 00000011 3 14 video input definition 80 10000000 1 2 8 d i g i t a l i n p u t 15 max h image size 1e 00011110 3 0 3 0 c m 16 max v image size 17 00010111 2 3 2 3 c m 17 display gamma 78 01111000 1 2 0 g a m m a 2 . 2 18 f eature support 0a 00001010 10 no dpms,active off,rgb color 19 red/green low bits 87 10000111 1 3 5 r x r y gxgy 1a blue/w h ite low bits f5 11110101 2 4 5 b x b y w x w y 1b red x/ high bits 94 10010100 148 rx= 0 .580 1c red y 57 01010111 87 ry = 0 .340 1d green x 4f 01001111 79 gx= 0 .310 1e green y 8c 10001100 140 gy = 0 .550 1f blue x 27 00100111 39 bx= 0 .155 20 blue y 27 00100111 39 by = 0 .155 21 wh ite x 50 01010000 80 w x = 0 .313 22 wh ite y 54 01010100 84 w y = 0 .329 www..net
d o c u m e n t v e r s i o n 0 . 1 3 4 / 3 7 b150xg02 v4 product specification 23 established timing 1 00 00000000 0 u n u s e d 24 established timing 2 00 00000000 0 25 manufacturer' s t i ming 00 00000000 0 26 standard timing #1 01 00000001 1 u n u s e d 27 01 00000001 1 28 standard timing #2 01 00000001 1 29 01 00000001 1 2a standard timing #3 01 00000001 1 2b 01 00000001 1 2c standard timing #4 01 00000001 1 2d 01 00000001 1 2e standard timing #5 01 00000001 1 2f 01 00000001 1 30 standard timing #6 01 00000001 1 31 01 00000001 1 32 standard timing #7 01 00000001 1 33 01 00000001 1 34 standard timing #8 01 00000001 1 35 01 00000001 1 36 pixel clock/10,000 (lsb) 64 01100100 100 timing descriptor #1 37 pixel clock/10,000 (msb) 19 00011001 25 1344x806 @60_mode:pixel clock= 65.00mhz 38 horiz. active pixels(low er 8 bits) 00 00000000 0 horiz active= 1024 pixels 39 horiz.blanking (low er 8 bits) 40 01000000 64 horiz blanking= 320 pixels 3a horiz. active pix e ls:horiz. blanking (upper4:4 bits) 41 01000001 65 3b 00 00000000 0 vertcal active= 768 lines 3c 26 00100110 38 vertical blanking= 38 lines 3d vert. active pix e ls:vert. blanking (upper4:4 bits) 30 00110000 48 3e 18 00011000 24 horiz sy nc. offset=24 pix e ls 3f 88 10001000 136 horiz sy nc. pulse w i dth= 136 pixels 40 vert. sy nc. offset=x x lines, sy nc w i dth= xx lines 36 00110110 54 verti sy nc. offset=3 lines,sy n c width=6 lines 41 horz. ver. sy nc/w idth (upper 2 bits) 00 00000000 0 42 hori. image size (low er 8 bits) 30 00110000 48 hori image size= 304.1 mm 43 vert. image size (low er 8 bits) e4 11100100 228 verti image size = 228.0mm 44 ho r i. ima g e size : vert. ima g e 10 00010000 16 www..net
d o c u m e n t v e r s i o n 0 . 1 3 5 / 3 7 b150xg02 v4 product specification size (upper 4 bits) 45 00 00000000 0 horizontal border = 0 46 00 00000000 0 vertical border = 0 47 18 00011000 24 48 detailed timing/monitor 00 00000000 0 fae suggest 49 descriptor #2 00 00000000 0 4a 00 00000000 0 4b 0f 00001111 15 4c 00 00000000 0 4d 00 00000000 0 4e 00 00000000 0 4f 00 00000000 0 50 00 00000000 0 51 00 00000000 0 52 00 00000000 0 53 00 00000000 0 54 00 00000000 0 55 00 00000000 0 56 00 00000000 0 57 00 00000000 0 58 00 00000000 0 59 20 00100000 32 5a f l ag 00 00000000 0 5b f l ag 00 00000000 0 5c f l ag 00 00000000 0 5d fe 11111110 254 5e 00 00000000 0 5f lcd vendor 41 01000001 65 a 60 lcd vendor 55 01010101 85 u 61 lcd vendor 4f 01001111 79 o 62 0a 00001010 10 63 20 00100000 32 64 00 00000000 0 65 20 00100000 32 66 20 00100000 32 67 20 00100000 32 68 20 00100000 32 69 20 00100000 32 6a 20 00100000 32 www..net
d o c u m e n t v e r s i o n 0 . 1 3 6 / 3 7 b150xg02 v4 product specification 6b 20 00100000 32 6c f l ag 00 00000000 0 monitor name: color lcd 6d f l ag 00 00000000 0 6e f l ag 00 00000000 0 6f data ty pe tag:ascii string fe 11111110 254 70 f l ag 00 00000000 0 71 manufacturer p/n 42 01000010 66 b 72 manufacturer p/n 31 00110001 49 1 73 manufacturer p/n 35 00110101 53 5 74 manufacturer p/n 30 00110000 48 0 75 manufacturer p/n 58 01011000 88 x 76 manufacturer p/n 47 01000111 71 g 77 manufacturer p/n 30 00110000 48 0 78 manufacturer p/n 32 00110010 50 2 79 20 00100000 32 7a manufacturer p/n 56 01010110 86 v 7b manufacturer p/n 34 00110100 52 4 7c 20 00100000 32 7d 0a 00001010 32 7e extension f l ag 00 00000000 0 7f checksum 00 00000000 0 www..net
document version 0.1 37/37 www..net

▲Up To Search▲

Price & Availability of B150XG02V4

	To Download B150XG02V4 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .