![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
your module no.: our module no.: K350QVG-V1-F your spec no.: our full spec no.: fs-K350QVG-V1-F-04 kitronix (dong guan) ltd. no. a20, luyi road, tianxin country, tangxi a town, dongguan city, guangdong province. for approval ? we are pleased in senddi ng you herewith our specification and drawing for your approval. plea se return to us one copy of ?for appoval? with your approved signatures. approved by approved by customer ???? kitronix (dong guan) ltd.
fs-K350QVG-V1-F 17/dec/2008 page 1 of 21 kitronix (dong guan) ltd. product specification product standard lcd module 320 x rgb x 240 dots 3.5? 262k colors tft display wide temperature with white led backlight with touch panel K350QVG-V1-F kitronix (dong guan) ltd. no. a20, luyi road, tianxin country, tangxi a town, dongguan city, guangdong province. fs-K350QVG-V1-F 17/dec/2008 page 2 of 21 kitronix (dong guan) ltd. product specification contents page no. 1. document revision history 3 2. general description 4 3. mechanical specifications 4 4. interface signals 6 5. absolute maximum ratings 7 6. electrical specifications 7 7. optical characteristics 8 8. timing characteristics 10 9. reliability test item 12 10. suggestions for using lcd modules 13 11. inspection standard 16 12. packing(reference only) 22 fs-K350QVG-V1-F 17/dec/2008 page 3 of 21 kitronix (dong guan) ltd. product specification 1. document revision history : document revision date description prepared by approved by 01 02 03 04 2008.04.28 2008.05.26 2008.12.11 2008.12.17 first release. change mistake and interface description. correct the mistake of input voltage and add the inspection standard. change the mechanical specifications. serlee van ng van ng van ng fs-K350QVG-V1-F 17/dec/2008 page 4 of 21 kitronix (dong guan) ltd. product specification 2. general description ? 3.5?(diagonal), 320 x rgb x 240 dots, 262k colors, transmissive, tft lcd module. ? viewing direction: 12 o?clock. ? driving ic: ssd2119 or equiva lent tft controller/driver. ? 18-bits data bus (parallel rgb inte rface/8080 parallel sy stem interface). ? with touch panel. ? with internal voltage booster. ? logic voltage: 3.3v (typ.). 3. mechanical specifications the mechanical detail is shown in fig. 1 and summarized in table 1 below. table 1 parameter specifications unit outline dimensions 76.9(w) x 63.9(h) x 4.4(d) (exclude fpc, cables of backlight) mm view area 72.88(w) x 55.36(h) mm tp view area 71.58 (w) x 54.2(h) mm lcd active area 70.08(w) x 52.56(h) mm display format 320 x rgb x 240 dots color configuration rgb stripes - color tft 320xrgbx240 dot size 0.219(rgb)(w) x 0.219(h) mm weight tbd grams fs-K350QVG-V1-F 17/dec/2008 page 5 of 21 kitronix (dong guan) ltd. product specification ???tpva0.3mm,?tpva?0.6mm figure 1: outline drawing fs-K350QVG-V1-F 17/dec/2008 page 6 of 21 kitronix (dong guan) ltd. product specification 4. interface signals table 2: pin assignment pin no. symbol description 1-2 led_k 3-4 led_a power supply for led backlight 5 gnd power supply (system ground) 6 xr 7 yd 8 xl 9 yu terminal of touch panel. 10 gnd power supply (system ground) 11-13 nc no connection 14 reset system reset pin 15 cs chip select pin 16 spclk clock pin of serial interface 17 sda-sdi data pin of serial interface 18-19 nc no connection 20-25 b[0-5] blue data 6-b it/18bit bi-directional (d0-d5) 26-27 nc no connection 28-33 g[0-5] green data 6-bit/ 18bit bi-directional (d6-d11) 34-35 nc no connection 36-41 r[0-5] red data 6-bit/ 18bit bi-directional (d12-d17) 42 hsync line synchronization signal input 43 vsync frame /ram synchronization signal input 44 dclk dot clock signal 45-46 avdd supply voltage for lcd driving 47-48 vcc supply voltage for logic 49 dc parallel interface 50 rd i80 system: serves as a read si gnal and reads data at the low level. 51 wr i80 system: serves as a write si gnal and writes data at the rising edge. 52-55 ps[0:3] interface selection pin ps3 ps2 ps1 ps0 interface mode 0 0 1 0 16-bit 8080 parallel interface, d[17:10]&d[8:1] 0 0 1 1 8-bit 8080 parallel interface, d[8:1] 0 1 0 0 9-bit rgb(262 colou r) + 3-wire spi, d[8:0] 0 1 0 1 16-bit rgb(262k colour) + 3-wire spi, d[17:10]&d[8:1] 0 1 1 0 18-bit rgb(262k colour) + 3-wire spi, d[17:0] 0 1 1 1 6-bit rgb(262k colour) + 3-wire spi, d[8:3] 1 0 1 0 18-bit 8080 parallel interface, d[17:0] 1 0 1 1 9-bit 8080 parallel interface, d[8:0] 1 1 1 0 3-wire spi 56 wsync ram write synchronization output 57 nc no connection 58 oe display enable pin from controller 59-60 gnd power supply (system ground) fs-K350QVG-V1-F 17/dec/2008 page 7 of 21 kitronix (dong guan) ltd. product specification 5. absolute maximum ratings 5.1 electrical maximum ra tings ? for ic only table 3: electrical ma ximum ratings ? for ic parameter symbol min. max. unit note supply voltage vcc -0.3 +4.0 v 1 input voltage avdd -0.3 +5.0 v note: 1.vcc, gnd must be maintained. 2.the modules may be destroyed if they are used beyond the absolute maximum ratings. 5.2 environmental condition table 4 operating temperature (topr) storage temperature (tstg) (note 1) item min. max. min. max. remark ambient temperature -20 c +70 c -30 c +80 c dry humidity (note 1) 80% max. rh for ta 40 c < 50% rh for 40 c < ta maximum operating temperature no condensation note 1: product cannot sustain at ex treme storage conditions for long time. 6. electrical specifications typical electrical characteristics at ta = 25 c, vcc=iovcc= 3.3v, gnd=0v. table 5 parameter symbol conditions min. typ. max. unit supply voltage (logic) vcc-gnd 1.4 - 3.6 v supply voltage (lcd driving) avdd 2.5 or vddio - 3.6 v vgh 9 - 18.0 v vgl -15.0 - -6 v output voltage(lcd) vcom -1 - 6 v supply current (logic & lcd) icc vdd=2.2v - - 10 ma supply voltage of white led backlight vled - 19.2 21.6 v luminance (on the module surface) forward current =20 ma number of led dies = 6 150 - - cd/m 2 fs-K350QVG-V1-F 17/dec/2008 page 8 of 21 kitronix (dong guan) ltd. product specification 7. optical characteristics table 7: optical specifications specifications items symbol condition min. typ. max. unit contrast ratio cr 200 300 - - t r - 15 30 ms response time t f - 35 50 ms x r 0.609 0.639 0.669 - red y r 0.314 0.344 0.374 - x g 0.264 0.294 0.324 - green y g 0.557 0.587 0.617 - x b 0.102 0.132 0.162 - blue y b 0.106 0.136 0.166 - x w 0.282 0.312 0.342 - chromaticity white y w 0.319 0.349 0.379 - 1(3 o?clock) - 45 - hor. 2(9 o?clock) - 45 - 2(12 o?clock) - 15 - viewing angle ver. 1(6 o?clock) center cr 10 - 35 - deg. ntsc ratio 61.5 % note note 1: definition of contrast ratio (cr): the contrast ratio can be calculated by the following expression. contrast ratio (cr) = l63 / l0 l63: luminance of gray level 63 l0: luminance of gray level 0 cr = cr (10) cr (x) is corresponding to the contrast ratio of the point x at figure in note 5. note 2: definition of response time (tr, tf): figure 3 fs-K350QVG-V1-F 17/dec/2008 page 9 of 21 kitronix (dong guan) ltd. product specification note 3: viewing angle figure 4 the above ?viewing angle? is the measuring pos ition with largest contrast ratio; not for good image quality. view direction for good image quality is 6 o?clock. module maker can increase the ?viewing angle? by applying wide view film. note 4: measurement set-up: the lcd module should be stabilized at a give n temperature for 20 minut es to avoid abrupt temperature change during measuring. in order to stabilize the luminance, the measurement should be executed after lighting backlight for 20 minutes in a windless room. figure 5 fs-K350QVG-V1-F 17/dec/2008 page 10 of 21 kitronix (dong guan) ltd. product specification 8. ac characteristics 8 .1 parallel 8080 timing characteristics fs-K350QVG-V1-F 17/dec/2008 page 11 of 21 kitronix (dong guan) ltd. product specification 9. reliability test item test item sample type test condi tion test result determinant gist normal temperature 703 ;96h high temperature storage wide temperature 803 ; 96h normal temperature -203 ; 120h low temperature storage wide temperature -303 ; 120h normal temperature 50 3 ,90%3%rh; 96h high temperature /humidity storage wide temperature 60 3 ,90%3%rh; 96h the inspection of appearance and function character. normal temperature 603 ;96h high temperature operation wide temperature 703 ;96h normal temperature 03 ;96h low temperature operation wide temperature -203 ;96h normal temperature 40 3 ,90%3%rh;96h high temperature /humidity operation wide temperature 50 3 ,90 %3%rh;96h no objection of the function character; no fatal objection of the appearance. normal temperature -203 ,30min 703 ,30 min;10cycle inspect the objections appearance function & the whole structure temperature shock wide temperature -303 ,30min 803,30min;10cycle the inspection of appearance function & the whole structure fs-K350QVG-V1-F 17/dec/2008 page 12 of 21 kitronix (dong guan) ltd. product specification 10. suggestions for using lcd modules 10.1 handling of lcm 1. the lcd screen is made of glass. don't give ex cessive external shock, or drop from a high place. 2. if the lcd screen is damaged and the liquid crysta l leaks out, do not lick and swallow. when the liquid is attach to your hand, skin, clot h etc, wash it off by using soap a nd water thoroughly and immediately. 3. don't apply excessive for ce on the surface of the lcm. 4. if the surface is contaminated ,c lean it with soft cloth. if the lc m is severely contaminated , use isopropyl alcohol/ethyl alcohol to clean. other solvents may damage the polarizer . the following solvents is especially prohibited: water , ketone aromatic solvents etc. 5. exercise care to minimize corrosion of the electr ode. corrosion of the elec trodes is accelerated by water droplets, moisture conde nsation or a current flow in a high-humidity environment. 6. install the lcd module by using the mounting holes. when mounting the lcd module make sure it is free of twisting, warping and distortion. in particular, do not forcibly pull or bend the i/o cable or the backlight cable. 7. don?t disassemble the lcm. 8. to prevent destruction of the elements by static el ectricity, be careful to maintain an optimum work environment. - be sure to ground the body when handling the lcd modules. - tools required for assembling, such as so ldering irons, must be properly grounded. - to reduce the amount of static electricity ge nerated, do not conduct assembling and other work under dry conditions. - the lcd module is coated with a film to protect the display surf ace. exercise care when peeling off this protective film since static electricity may be generated. 9. do not alter, modify or change the the shape of the tab on the metal frame. 10. do not make extra holes on the printed circuit boa rd, modify its shape or change the positions of components to be attached. fs-K350QVG-V1-F 17/dec/2008 page 13 of 21 kitronix (dong guan) ltd. product specification 11. do not damage or modify the patt ern writing on the pr inted circuit board. 12. absolutely do not modify the zebra rubber stri p (conductive rubber) or heat seal connector 13. except for soldering the interface, do not make any alterations or modifications with a soldering iron. 14. do not drop, bend or twist lcm. 10.2 cautions for installing and assema bling if the module has touch panel 1. use a buffer material (gasket) between the touch panel and front- case to protect damage and wrong operating. the dimension of the buffer material?s edge between the tp v.a. edge is min. 0.3mm. 2. we recommend to design a case that it can?t ov er the boundary of the activ e area max. 0.5mm in order to prevent an operation at outside of the active area which can?t guarantee the specified durability, because operation at the outside of the active area cause serious damage of a transparent. 3. when design case for installing module, you would consider give a distance about 0.2 0.15mm between the module edge to case inside. 4. the corners of the product are not chamfered. when positioning and fixing the pr oduct on the case, we sugguest that you would provide a r pa rt on the conner of the case so as not to apply load on the corner of the transparent module. ? ? ? ? fs-K350QVG-V1-F 17/dec/2008 page 14 of 21 kitronix (dong guan) ltd. product specification 10.3 storage 1. store in an ambient temperature of 5 to 45 c, and in a relative humidity of 40% to 60%. don't expose to sunlight or fluorescent light. 2. storage in a clean environment, free from dust, active gas, and solvent. 3. store in antistatic container. fs-K350QVG-V1-F 17/dec/2008 page 15 of 21 kitronix (dong guan) ltd. product specification 11. inspection standard this specification is made to be used as the standa rd acceptance/rejection crit eria for color mobile phone lcm with touch pannel. 11.1 sample plan and inspection condition 11.1.1 sample plan sampling plan according to mil-std-105e , normal level 2 and based on: major defect: aql 0.65; minor defect: aql 1.5. 11.1.2 inspection condition viewing distance for cosmetic inspection is about 30cm with bare eyes, and under an environment of 20~40w light intensity, all directions for inspecting th e sample should be within 45 against perpendicular line. 11.2 definition of inspection zone in lcd inspection zones in an lcd zone a: character/digit area; zone b: viewing area except zone a (zonea+zoneb=minimum viewing area); zone c: outside viewing area (invisible ar ea after assembly in customer?s product); note: as a general rule, visual defects in zone c are permissible, when it is no trouble for quality and assembly of customer?s product. def ects are classified as major defect s and minor defects according to the degree of defectiveness defined herein. 11.3 major defects and minor defects 11.3.1 major defects a major defect is a defect that is likely to result in failure, or to re duce the usability of the product for its intended purpose. 11.3.1.1 abnormal operation: modules cannot display normally; fs-K350QVG-V1-F 17/dec/2008 page 16 of 21 kitronix (dong guan) ltd. product specification 11.3.1.2 line defect; 11.3.1.3 there is serious distortion or sharp burr on mechanical housing; 11.3.1.4 glass breakage. 11.3.2 minor defects: a minor defect is a defect that is not likely to reduce the usabili ty of the product for its intended purpose. 11.3.2.1 dot defect: 11.3.2.1.1 inspection pattern : full white, full black, red, green and blue screens; 11.3.2.1.2 criteria :(acceptable); note: 1. dot defect is defined as the defective area of the dot area is larger than 50% of the dot area . and the bright dot defect must be visible through 5% nd filter. 2. except for the allowed numbers of adjacent dots , the distance between dot defects should be more than 3mm apart. 11.3.2.1.3 the definitions of the inner disp lay area and outer display area. 11.4 inspection standards table: 11.4.1 major defect item no. items to be inspection standard classification of defects 11.4.1.1 all functional defects 1) no display 2) display abnormally 3) missing vertical/horizontal segment 4) short circuit 5) back-light no ligh ting, flickering and abnormal lighting. 11.4.1.2 missing missing component 11.4.1.3 outline dimension overall outline dimension beyond the drawing is not allowed. 11.4.1.4 linearity no more than 1.5% major 1/5 3/5 1/5 1/5 3/5 1/5 sub-pixel fs-K350QVG-V1-F 17/dec/2008 page 17 of 21 kitronix (dong guan) ltd. product specification 11.4.2 cosmetic defect (spot defect) item no itemsto be inspection standard classification of defects for dark/white spot, size is defined as =( x +y )/2 minor 11.4.2.1 clear spots black and white spot defect pinhole, foreign particle, polarizer dirt acceptable qty zone size(mm) a b c ? 0.1 ignore 0.10 ? 0.15 2 0.15 ? 0.20 1 0.20 0 ignore minor 11.4.2.2 clear spots tp dirt acceptable qty zone size(mm) a b c ? 0.1 ignore 0.10 ? 0.15 2 0.15 ? 0.25 1 0.25 0 ignore minor 11.4.2.3 dim spots circle shaped and dim edged defects acceptable qty zone size(mm) a b c ? 0.2 ignore 0.20 ? 0.4 2 0.4 ? 0.6 1 0.6 0 ignore minor 11.4.2.4 dot defect dot =sub-pixel acceptable qty i ii bright dot 0 2 dark dot 1 2 the distance of two point >5mm minor 11.4.3 cosmetic defect (linear defect) item no items to be inspection standard classification of defects 11.4.3.1 line defect black line, white line, foreign material on polarizer size(mm) acceptable qty zone l(length) w(width) a b c ignore w 0.02 ignore l 3.0 0.02 w 0.03 2 l 2.0 0.03 w 0.05 1 w 0.05 define as spot defect ignore minor fs-K350QVG-V1-F 17/dec/2008 page 18 of 21 kitronix (dong guan) ltd. product specification 11.4.3.2 foreign material on tp film the line can be seen after mobile phone in the operating condition: size(mm) acceptable qty zone l(length) w(width) a b c ignore w 0.03 ignore l 3.0 0.03 w 0.05 3 w 0.05 define as spot defect ignore minor 11.4.3.3 dim line defect polarizer &bl scratch tp film scratch if the scratch can be seen after mobile phone cover assembling or in the operating condition, judge by the line defect of 11.4.3.1. if the scratch can be seen only in non-operating condition or some special angle, judge by the following. size(mm) acceptable qty zone l(length) w(width) a b c ignore w 0.02 ignore l 3.0 0.02 w 0.03 2 l 2.0 0.03 w 0.05 1 w 0.05 define as spot defect ignore minor 11.4.3.4 polarize air bubble air bubbles between glass & polarizer acceptable qty a b c ? 0.2 ignore 0.20 ? 0.3 2 0.3 ? 0.5 1 0.5 0 ignore minor 11.4.4 chipping defect item no items to be inspection standard classification of defects 11.4.4.1 glass defect chips on corner a:lcd glass defect x y z 0.2 s disregard notes: s=contact pad length chips on the corner of terminal shall not be allowed to extend into the ito pad or expose perimeter seal. b:tp glass defect x y z 3.0 3.0 disregard minor fs-K350QVG-V1-F 17/dec/2008 page 19 of 21 kitronix (dong guan) ltd. product specification usual surface cracks a:lcd glass defect x y z 3.0 fs-K350QVG-V1-F 17/dec/2008 page 20 of 21 kitronix (dong guan) ltd. product specification 3 film impression: with operati on, must be invisibility. 4 touch panel knob if writing function normally, it could be allowed. 5 newton ring without operation, the color circle of regularity or non-regularity from the normal or slope angle of view. 1 regularity the area of the newton ring is less than 1/3 area of the touch panel; and no character affected and line distorted after touch panel lightening. it?s ok. 2 non- regularity the area of the newton ring is less than the 1/2 area of touch panel w ith lightening. and no character affected and line 11.4.5.4 backlight elements 1 illumination source flickers when lit. 2 spots or scratches that appear when lit must be judged using lcd spot, lines and contamination standards. 3 backlight doesn?t li ght or color is wrong major 11.4.5.5 soldering 1 no unmelted solder paste may be present on the fpc 2 no cold solder joints, missi ng solder connections, oxidation or icicle. 3 no short circuits in components on fpc major fs-K350QVG-V1-F 17/dec/2008 page 21 of 21 kitronix (dong guan) ltd. product specification 12. packing (reference only) packing method (1) (2) (3) (4) (5) (6) 1. put module into tray cavity : 2. tray stacking 3. put 1 cardboard unde r the tray stack and 1 cardboard above: 4. fix the cardboard to the tray stack with adhesive tape: 5. put th e tray stack into carton. 6. carton sealing with adhesive tape. - end - |
Price & Availability of K350QVG-V1-F
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |