View M170XW01-V2_4637200.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

v e r0.5 1/26 p r od u ct s p ecificati on m170x w 01 v.2 a u optronics corpor a tion produ ct s pecification 17.0 w x g a c olor t f t -lcd m odule m odel na m e : m 170x w 01 v .2 approved b y prepared b y ddbu marketing division / au optronics corporation custo m er chec k ed & approved b y www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 2/26 product specification m170xw01 v.2 product specification 17.0 wxga color tft-lcd module model name: m170xw01 v.2 ( u ) preliminary specifications ( ) final specifications note: this specification is subject to change without notice. www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 3/26 product specification m170xw01 v.2 contents 1.0 handling precautions.............................................................6 2.0 general description...............................................................7 2.1 display characteristics ...............................................................................................................7 2.2 optical characteristics ...............................................................................................................8 3.0 functional block diagram.....................................................11 4.0 absolute maximum ratings..................................................12 5.0 electrical characteristics......................................................13 5.1 tft lcd module .......................................................................................................................13 5.1.1 power specification...............................................................................................13 5.1.2 signal electrical characteristics..............................................................................14 5.2 backlight unit ............................................................................................................................15 6.0 signal characteristic............................................................16 6.1 pixel format image ...................................................................................................................16 6.2 the input data format ...............................................................................................................16 6.3 signal description .....................................................................................................................17 6.4 interface timings .......................................................................................................................18 6.4.1 timing characteristics...........................................................................................18 6.4.2 timing diagram....................................................................................................19 6.5 power on/off sequence .......................................................................................................20 7.0 connector & pin assignment................................................21 7.1 tft lcd module .......................................................................................................................21 7.2 backlight unit ............................................................................................................................21 8.0 vibration, shock, and drop...................................................22 8.1 vibration & shock .....................................................................................................................22 8.2 drop test ....................................................................................................................................22 9.0 environment........................................................................22 9.1 temperature and humidity .......................................................................................................22 9.1.1 operating conditions............................................................................................22 9.1.2 shipping conditions..............................................................................................22 9.2 atmospheric pressure ..............................................................................................................23 9.3thermal shock ...........................................................................................................................23 10.0 reliability...........................................................................23 10.1 failure criteria ........................................................................................................................23 10.2 failure rate .............................................................................................................................23 10.2.1 usage................................................................................................................23 www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 4/26 product specification m170xw01 v.2 11.0 safety................................................................................23 11.1 sharp edge requirements .....................................................................................................23 11.2 materials ..................................................................................................................................24 11.2.1 toxicity.............................................................................................................24 11.2.2 flammability......................................................................................................24 11.3 capacitors ................................................................................................................................24 12.0 other requirement.............................................................24 12.1 national test lab requirement .............................................................................................24 12.2 label ........................................................................................................................................24 13.0 mechanical characteristics.................................................25 www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 5/26 product specification m170xw01 v.2 record of revision version and date page old description new description remark 0.1 2004/03/26 all first edition for customer all 0.2 2004/05/24 13 idd (typ= tbd, max= tbd) idd (typ= 950, max= 1200 ma) update 13 irush= (max= tbd) irush= (max= 3.0 a) update 13 pdd (typ= tbd, max= tbd) pdd (typ= 4.75, max= 6.6 w) update 18 data clk(min= 35, max= 83mhz) h-period (min= 1320 tclk) v-period (max= 823 th) frame rate (max= 80hz) data clk(min= 45, max= 81mhz) h-period (min= 1330 tclk) v-period (max= 860 th) frame rate (max= 75hz) update 20 power on/off sequence t1 (min= na) ; t6 (min= na) power on/off sequence t1 (min=0.5 ms) ; t6 (min=0.5 ms) update 0.3 2004/05/27 15 ltcfl (min= 30,000 hours) (typ= na) ltcfl (min= 25,000 hours) (typ= 35,000 hours) update 0.4 2004/07/02 15 ltcfl (min= 30,000 hours) (typ= na) ltcfl (min= 25,000 hours) (typ= 35,000 hours) update 0.5 2004/07/29 08 brightness uniformity min= 75%, typ= 80% brightness uniformity min= 70%, typ= 75% update www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 6/26 product specification m170xw01 v.2 1.0 handling precautions 1) since front polarizer is easily damaged, pay attention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact with water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) in case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the ccfl reflector edge. instead, press at the far ends of the ccfl reflector edge softly. otherwise the tft module may be damaged. 10) at the insertion or removal of the signal interface connector, be sure not to rotate nor tilt the interface connector of the tft module. 11) after installation of the tft module into an enclosure (desktop monitor bezel, for example), do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the tft module from outside. otherwise the tft module may be damaged. www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 7/26 product specification m170xw01 v.2 2.0 general description this specification applies to the 17.0 inch color tft/lcd module m170xw01 v.2. this module is designed for a display unit of personal computer. the display supports the wxga (1280(h) x 768(v)) screen format and 16.2m colors (rgb 6-bits + frc data). all input signals are 1 channel lvds interface compatible. this module does not contain an inverter card for backlight. 2.1 display characteristics the following items are characteristics summary on the table under 25 condition: items unit specifications screen diagonal [mm] 432(17.0" wide) active area [mm] 370.56 (h) x 222.34(v) pixels h x v 1280(x3) x 768 pixel pitch [mm] 0.2895 (per one triad) x 0.2895 pixel arrangement r.g.b. vertical stripe display mode normally black white luminance [cd/m 2 ] 450 (typ, center @ lamp= 11.0ma) contrast ratio 800 : 1 optical response time (gray to gray) [msec] 16 (typ) nominal input voltage vdd [volt] +5.0 v power consumption (vdd line + ccfl line) [watt] tbd w(typ) (pdd=tbd w, pcfl=tbd w @lamp=11.0ma) weight [grams] 2000 (typ) min. typ. max. horizatal(h) 403.5 404.0 404.5 vertical(v) 248.0 248.5 249.0 physical size [mm] depth(d) 16.8 17.3 17.8 electrical interface 1 channel lvds support color 16.2m colors (rgb 6-bit + frc data) surface treatment glare type, hard coating (2h) temperature range operating storage (shipping) [ o c] [ o c] 0 to +50 -20 to +60 www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 8/26 product specification m170xw01 v.2 l c d m o d u l e pr-880 / bm5a / bm7 module driving equipment measuring distance 2.2 optical characteristics the optical characteristics are measured under stable conditions at 25 : item unit conditions min. typ. max. note horizontal (right) cr = 10 (left) 75 75 85 85 - - viewing angle [degree] vertical (up) cr = 10 (down) 75 75 85 85 - - contrast ratio normal direction 600 800 - rasing time - 15 25 falling time - 10 15 raising + falling - 25 40 response time [msec] gray to gray - 16 - note 1 red x 0.61 0.64 0.67 red y 0.31 0.34 0.37 green x 0.26 0.29 0.32 green y 0.58 0.61 0.64 blue x 0.11 0.14 0.17 color / chromaticity coordinates (cie) blue y 0.04 0.07 0.10 white x 0.28 0.31 0.34 color coordinates (cie) white white y 0.30 0.33 0.36 white luminance @ ccfl 11.0ma (center) [cd/m 2 ] 400 450 - luminance uniformity [%] 70 75 note 2 crosstalk (in 75hz) [%] - - 1.5 note 3 flicker db - - -20 note 4 equipment : pattern generator, power supply, digital voltmeter, luminance meter (pr 880, bm-5a / bm7) aperture 1 with 100cm vd or 2 with 50cm viewing distance test point center (vesa point 9) environment < 1 lux www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 9/26 product specification m170xw01 v.2 note 1: the definition of response time the output signals of photodetector are measured when the input signals are changed from black to white (rising time), and from white to black (falling time), respectively. the response time is interval between the 10% and 90% of amplitudes. note 2: brightness uniformity of these 9 points is defined as below 9) - (1 points 9 in luminance maximum 9) - (1 points 9 in luminance minimum uniformity = 50 % 90 % 90 % 50 % 10 % 10 % 100 90 10 0 % optical response white black white tr f tr r 100 90 10 0 % optical response white black white tr f tr r www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 10/26 product specification m170xw01 v.2 note 3: the definition of crosstalk unit: percentage of dimension of display area l l a -l a l / l a x 100%= 1.5% max., l a and l b are brightness at location a and b l l b -l b l / l b x 100%= 1.5% max., l a and l b are brightness at location a and b note4: the definition of flicker test paterm: subchecker pattern r g b r g b r g b r g b r g b r g b method: record dbv & dc value with (westar)trd-100 level dc hz) 30 level(at ac log 20 (db) flicker = 0 gray level 1/2 1/2 1/6 1/6 a b 1/2 1/2 1/6 1/6 2/3 1/3 1/3 2/3 a b 184 gray level 184 gray level gray level = l127 gray level = l0 amplitude time dc ac www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 11/26 product specification m170xw01 v.2 3.0 functional block diagram the following diagram shows the functional block of the 17.0 inches wide color tft/lcd module: hirose df14h-20p-1.25h bhsr-02vs-1 mating type : hirose df14-20s-1.25c sm02b-bhss-1-tb c o n n e c t o r dc/dc converter lvds receiver timing controller gamma correction tft-lcd 1280*(3)*768 pixels x - driver ic y - d r i v e r i c g1 g768 d1 d3840 inverter dc power auo asic over-driver lvds + 5 v www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 12/26 product specification m170xw01 v.2 4.0 absolute maximum ratings absolute maximum ratings of the module is as following: tft lcd module item symbol min max unit conditions logic/lcd drive vin -0.3 +5.5 [volt] note 1,2 backlight unit item symbol min max unit conditions ccfl current icfl - 12.0 [ma] rms note 1,2 ccfl frequency fcfl 40 80 [hz] note 1,2 absolute ratings of environment item symbol min max unit conditions operating humidity hop 8 95 [%rh] storage temperature tst -20 +60 [ o c] storage humidity hst 8 95 [%rh] note 1: with in ta (25 ) note 2: permanent damage to the device may occur if exceed maximum values t=65 ,h=29% relative humidity % temperature - 20 0 60 50 95 5 100 0 operatio n range storage range storage range 80 60 40 20 twb=39 t=40 ,h=95% t=60 ,h=39% t=50 ,h=55% www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 13/26 product specification m170xw01 v.2 5.0 electrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows; symbol parameter min typ max units condition vdd logic/lcd drive voltage 4.5 5 5.5 [volt] 10% idd vdd current - 950 1200 [ma] vin=5v , all white pattern, +30%, at 75hz irush lcd inrush current - - 3.0 [a] note pdd vdd power - 4.75 6.6 [watt] vin=5v , all white pattern, +30%, at 75hz vddrp allowable logic/lcd drive ripple voltage 100 [mv] p-p note: measurement conditions: +5.0v +12.0v sw vcc r1 47k r2 1k vr1 47k f1 q3 ao6402 g d 2 s d 1 d 5 d 6 c1 1uf/16v q3 ao6402 g d2 s d1 d5 d6 c3 0.01uf/25v c2 1uf/25v (high to low) control signal (lcd module input) 90% 10% vin rising time 0 v 5. 0 v 470 us www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 14/26 product specification m170xw01 v.2 5.1.2 signal electrical characteristics each signal characteristics are as follows; symbol parameter min typ max units condition vth differential input high threshold - - +100 [mv] vicm = 1.2v note vtl differential input low threshold -100 - - [mv] vicm = 1.2v note vid input differential voltage 100 400 600 [mv] note vicm differential input common mode voltage 1.1 - 1.45 [v] vth/vtl = 100mv note note: lvds signal waveform vth vid vtl vicm vss www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 15/26 product specification m170xw01 v.2 5.2 backlight unit parameter guideline for ccfl inverter symbol parameter min. typ. max. unit condition iscfl ccfl standard current 10.5 11.0 11.5 [ma] rms (ta=25 o c) note 1 ircfl ccfl operation range 5.5 11.0 12.0 [ma] rms (ta=25 o c) fcfl ccfl frequency 40 60 80 [khz] (ta=25 o c) note 2 vicfl (0 o c) ccfl ignition voltage (end of the lamp wire connector) 1650 - - [volt] rms (ta=0 o c) vicf (25 o c) ccfl ignition voltage (end of the lamp wire connector) 1250 - - [volt] rms (ta=25 o c) vcfl ccfl operation voltage - 560 @11.0ma 680 @5.5ma [volt] rms (ta=25 o c) note 3 pcfl ccfl power consumption (for reference) - 24.6 28 [watt] (ta=25 o c) note 4 ltcfl ccfl life time 25,000 35,000 - [hour] (ta=25 o c) note 5 note 1: ccfl standard current is measured at 25 2 . the variance of the current is 10%. note 2: ccfl frequency should be carefully determined to avoid interference between inverter and tft lcd note 3: ccfl operation voltage is measured at 25 2 . note 4: the variance of ccfl power consumption is 10%. calculator value for reference (icfl vcfl 4=pcfl). note 5: ccfl life time is determined as the time at which brightness of lamp is 50%.the typical life time of ccfl is on the condition at 11.0ma lamp current. www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 16/26 product specification m170xw01 v.2 6.0 signal characteristic 6.1 pixel format image following figure shows the relationship of the input signals and lcd pixel format. r g b r g b r g b r g b r g b r g b r g b r g b 1 2 1279 1280 1st line 768 line 6.2 the input data format vdiff=0v devshsb5b4b3b2 b1b0g5g4g3g2g1 g0r5r4r3r2r1r0 previousdata for currentclk cycle next rxclkin rxin0 rxin1 rxin2 rsvb7b6g7g6r7r6 rxin3 vdiff=0v devshsb5b4b3b2 devshsb5b4b3b2 b1b0g5g4g3g2g1 b1b0g5g4g3g2g1 g0r5r4r3r2r1r0 g0r5r4r3r2r1r0 previousdata for currentclk cycle next rxclkin rxin0 rxin1 rxin2 rsvb7b6g7g6r7r6 rsvb7b6g7g6r7r6 rxin3 r/g/b data 7: msb, r/g/b data 0: lsb www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 17/26 product specification m170xw01 v.2 6.3 signal description the module using one lvds receiver sn75lvds82(texas instruments) or compatible. lvds is a differential signal technology for lcd interface and high speed data transfer device. transmitter shall be sn75lvds83(negative edge sampling) or compatible . pin no. signal name description 1 vcc +5.0v power supply 2 vcc +5.0v power supply 3 vss power ground 4 vss power ground 5 rxin0- negative lvds differential data input 6 rxin0+ positive lvds differential data input 7 vss power ground 8 rxin1- negative lvds differential data input 9 rxin1+ positive lvds differential data input 10 vss power ground 11 rxin2- negative lvds differential data input 12 rxin2+ positive lvds differential data input 13 vss power ground 14 rxclkin- negative lvds differential clock input 15 rxclkin+ positive lvds differential clock input 16 vss power ground 17 rxin3- negative lvds differential data input 18 rxin3+ positive lvds differential data input 19 vss power ground 20 nc no connection (for auo test) note 1: all gnd (ground) pins should be connected together and to vss which should also be connected to the lcd s metal frame. note 2: all vcc (power input) pins should be connected together. www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 18/26 product specification m170xw01 v.2 note 3: the drawing of connector. 6.4 interface timings 6.4.1 timing characteristics item symbol min typ max unit data clk tclk 45 64 81 mhz period th 1330 1350 1440 tclk h-section display area tdisp(h) 1280 1280 1280 tclk period tv 777 790 860 th v-section display area tdisp(v) 768 768 768 th frame rate f 47 60 75 hz note: de mode only. 20 1 www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 19/26 product specification m170xw01 v.2 6.4.2 timing diagram de de clk tclk tblk(v) th tv tdisp(v) tdisp(h) th tblk(h) www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 20/26 product specification m170xw01 v.2 6.5 power on/off sequence vin and lamp power on/off sequence are as follows. the timing parameters of interface signal are shown in the table below. values symbol min. typ. max. unit t1 0.5 - 10 ms t2 0.5 25 50 ms t3 200 - - ms t4 200 - - ms t5 0.5 16 50 ms t6 0.5 - 10 ms t7 1000 - - ms 90% 90% 10% 10% t1 t2 t5 t6 t7 t3 t4 0 v lamp signal vin 10% 0 v 0 v www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 21/26 product specification m170xw01 v.2 7.0 connector & pin assignment physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. 7.1 tft lcd module connector name / designation interface connector / interface card manufacturer hirose or compatible type part number df14h-20p-1.25h mating housing part number df14-20s-1.25c pin no. signal name pin no. signal name 1 vcc, +5.0v 11 rxin2- 2 vcc, +5.0v 12 rxin2+ 3 vss 13 vss 4 vss 14 rxclkin- 5 rxin0- 15 rxclkin+ 6 rxin0+ 16 vss 7 vss 17 rxin3- 8 rxin1- 18 rxin3+ 9 rxin1+ 19 vss 10 vss 20 nc (for auo test) 7.2 backlight unit connector name / designation lamp connector / backlight lamp manufacturer jst type part number bhsr-02vs-1 mating type part number sm02b-bhss-1-tb pin no. input color function 1 hot1 pink high voltage 2 cold1 white low voltage 3 hot2 blue high voltage upper 4 cold2 black low voltage 1 hot1 pink high voltage 2 cold1 white low voltage 3 hot2 blue high voltage lower 4 cold2 black low voltage www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 22/26 product specification m170xw01 v.2 8.0 vibration, shock, and drop 8.1 vibration & shock vibration test spec: l frequency: 10 - 200hz l sweep: 30 minutes each axis (x, y, z) l acceleration: 1.5g(10~200hz p- p) l test method: acceleration (g) 1.5 frequency (hz) 10~200~10 active time (min) 30 shock test spec: acceleration (g) C a 50 active time -b 20 ms wave form half-sin times 1 l direction: x , y, z 8.2 drop test package test: the drop height is 60cm. 9.0 environment the display module will meet the provision of this specification during operating condition or after storage or shipment condition specified below. operation at 10% beyond the specified range will not cause physical damage to the unit. 9.1 temperature and humidity 9.1.1 operating conditions the display module operates error free, when operated under the following conditions; temperature 0 0 c to 50 0 c relative humidity 8% to 95% wet bulb temperature 39.0 0 c 9.1.2 shipping conditions the display module operates error free, after the following conditions; temperature -20 0 c to 60 0 c relative humidity 5% to l00% wet bulb temperature 39.0 0 c www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 23/26 product specification m170xw01 v.2 9.2 atmospheric pressure the display assembly is capable of being operated without affecting its operations over the pressure range as following specified; pressure note maximum pressure 1040hpa (sea level) minimum pressure 674hpa (3048m) 9.3 thermal shock the display module will not sustain damage after being subjected to 100 cycles of rapid temperature change. a cycle of rapid temperature change consists of varying the temperature from -20 0 c to 60 0 c, and back again. thermal shock cycle -20 0 c for 30min 60 0 c for 30min power is not applied during the test. after temperature cycling, the unit is placed in normal room ambient for at least 4 hours before powering on. 10.0 reliability this display module and the packaging of that will comply following standards. 10.1 failure criteria the display assembly will be considered as failing unit when it no longer meets any of the requirements stated in this specification. only as for maximum white luminance, following criteria is applicable. l maximum white luminance shall be 150cd/m 2 or more. 10.2 failure rate the average failure rate of the display module (from first power-on cycle till 1,000 hours later) will not exceed 1.0%. the average failure rate of the display module from 1,000 hours until 16,000 hours will not exceed 0.7% per 1000 hours. 10.2.1 usage the assumed usage for the above criteria is: l 220 power-on hours per month l 500 power on/off cycles per month l maximum brightness setting l operation to be within office environment (25 0 c typical) 11.0 safety 11.1 sharp edge requirements there will be no sharp edges or comers on the display assembly that could cause injury. www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 24/26 product specification m170xw01 v.2 11.2 materials 11.2.1 toxicity there will be no carcinogenic materials used anywhere in the display module. if toxic materials are used, they will be reviewed and approved by the responsible adt toxicologist. 11.2.2 flammability all components including electrical components that do not meet the flammability grade ul94-v1 in the module will complete the flammability rating exception approval process. the printed circuit board will be made from material rated 94-v1 or better. the actual ul flammability rating will be printed on the printed circuit board. 11.3 capacitors if any polarized capacitors are used in the display assembly, provisions will be made to keep them from being inserted backwards. 12.0 other requirement 12.1 national test lab requirement the display module will satisfy all requirements for compliance to ul 1950, first edition u.s.a. information technology equipment csa c22.2 no.950-m89 canada, information technology equipment eec 950 international, information technology equipment en 60 950 international, information processing equipment (european norm for iec950) 12.2 label the label is on the panel as shown below: www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 25/26 13.0 mechanical characteristics www.datasheet.co.kr datasheet pdf - http://www..net/
ver0.5 26/26 www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of M170XW01-V2

	To Download M170XW01-V2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .