apex microtechnology corporation ? telephone (520) 690-8600 ? fax (520) 888-3329 ? orders (520) 690-8601 ? email prodlit@apexmicrotech.com 1 introduction the EK14 evaluation kit provides a convenient way to bread - board circuits using apex power op amps packaged in the 12-pin sip03 package. the ampli?er may be mounted vertically with the hs20 heat sink, or horizontally. connections are provided for required power supply bypassing, external compensation components, as well as current limit resistors. a large area for component mounting provides ?exibility and makes a multitude of circuit con?gurations possible. caution use the supplied thermal washers or ther - mal grease between the power ampli?er and the heat sink. parts list part # description quantity hs20 heatsink 1 eval16 pc board 1 ms06 mating socket 1 ox7r105kwn 1f ceramic capacitor 2 csr10 .15 resistor 2 two7 thermal washer 1 package before you get started ? all apex ampli?ers should be handled using proper esd precautions. ? always use the heat sink and thermal washers included in this kit. ? always use adequate power supply bypassing. ? do not change connections while the circuit is powered. ? initially set all power supplies to the minimum operating levels allowed in the device data sheet. ? check for oscillations. assembly 1. on the silk screen side of the evaluation board, insert and solder the ms06 mating socket in dut holes 1 C 12. be sure each one is fully seated. 2. solder components for your circuit. be sure to include proper bypassing, required compensation components and current limit resistors. see the op amp data sheet for help in select - ing these components. 1uf capacitors and a .15 resistor have been included with the ek12 kit but may be replaced with other components as necessary. 3. place the tw07 thermal washer on the heat sink over the mounting hole for the dut. place a #6 screw through the mounting hole and thread a #6 nut onto the screw at the back of the heat sink. do not tighten. note that there are two sets of mounting holes on the hs20. holes on one edge allow room between the dut and evaluation board for the ms06 socket. the holes on the other edge are for direct through hole mounting of the dut to the evaluation board. it is recommended that you use the ms06. 4. mount the dut to the hs20 by sliding under the head of the #6 screw and on top of the thermal washer. tighten the nut to the speci?ed 8 to 10 in-lbs. (.9 to .13 n*m). do not over torque. 5. install leads of the dut into the ms06 on the evaluation board. use #6 self-tapping screws to secure the evaluation board to the hs20 heat sink as shown in the assembly diagram (figure 1). ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ????????????????????????????????????? ????
apex microtechnology corporation ? 5980 north shannon road ? tucson, arizona 85741 ? usa ? applications hotline: 1 (800) 546-2739 2 EK14 evaluation kit for sip03 pin-out ?????? ????????? ???????????? ???? ???? ???????? ??????????? ?????????????? ?????????? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ????? ????? ??? ??? ??? ?? ?? ??? ? ??? ?? ?? ??? ?????? ?????? ?? ?? ? ? ??? ??? ??? ???? ? ???? ? ?? ??? this data sheet has been carefully checked and is believed to be reliable, however, no responsibility is assumed for possible inaccuracies or omissions. all speci?cations are subject to change without notice. EK14u rev b october 2004 ? 2004 apex microtechnology corp. figure 1. pcb
|
