View A081VW01-V0_5569934.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

doc . v ers io n : 0 .8 c (for e s7 or l at er) tota l pa g es : 3 2 da te : 20 0 8/ 0 4/ 02 note: the content of this specification is subject to change. ? 2006~2007 au optronics all rights reserved model name: a081vw01 product specifications 8.1 color tft-lcd module < > preliminary specification < > final specification www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 1 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. record of revision version revise date page content 0 2006/07/10 first draft. 0.1 2006/09/05 5 ~ 6 7~9 20 21 update outline dimension re-define pin assignment sequence update suggested application circuit update response time 0.2 2006/10/18 4~5 9 update outline dimension and outline drawing re-define pin assignment (57~60) sequence 0.3 2007/01/26 4~6 19 22~24 updated outline dimension and outline drawing (lcd glass: t0.5) updated brightness when w/ touch panel added touch panel spec 0.4 2007/02/13 14~16 26~27 updated recommended register setting added recommended application circuit 0.4a 2007/03/01 23 correct reliability test items 0.5 2007/03/13 4~6 updated outline dimension and drawing (tp: glass:t1.8, dsa: 0.6) 3 general description modification. 5~6 updated outline drawing for touch panel fpc length 7~9 updated pin description. 11 updated dclk frequency and period. 13 ~ 17 updated spi timing, register default esettings and description. 18 added stand-by mode timing. 28 ~ 29 updated power on/off sequence. 0.6 2007/03/27 30 added recommend register settings. 0.6a 2007/04/01 5~6 updated outline drawing for touch panel fpc dimension 5~6 updated outline drawing for fpc outline 15 updated register table default value 18 updated register r6 description 0.6b 2007/05/15 31 updated recommend register settings 0.7 2007/08/10 10~11 updated pin assignment www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 2 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 12 updated typical operation condition 18 updated r1 description 30 updated application circuit 33 updated recommended register settings and sequence 34 updated gamma2.2 voltage 6 updated outline drawing, the suggested customer housing design 0.7a 2007/09/11 23~24 updated touch panel electronic charistics and life test condition 0.7b 2007/09/27 19 updated backlight led driving voltage 10 updated abolute maximum ratings 19 updated led backlight by 4 leds serial type 28 updated application circuit 31 updated recommand register settings 0.8 2007/10/17 32 updated gamma2.2 voltage and recommanded resistors. 9 updated de mode description 28 updated register r516 from 10k to 0 ohm 0.8a 2007/11/19 31 updated recommand register settings 0.8b 2008/03/31 20 define min. to cr and viewing angle 0.8c 2008/04/02 7 updated outline drawing due to blu label shift www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 3 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. contents features ............................................ ................................................... ................................................... ...........4 1. general information................................ ................................................... ..............................................5 2. electrical specifications ........................... ................................................... .........................................8 2.1 fpc p in a ssignment (hrs fh27-60h-0.4sh) ....................................... ................................................... 8 2.2 a bsolute m aximum r atings ................................................... ................................................... ..............10 2.3 e lectrical c haracteristics ................................................... ................................................... ............11 2.4 ac c haracteristics ................................................... ................................................... ..........................11 2.5 rgb p arallel i nput t iming ................................................... ................................................... ...............12 2.6 s erial c ontrol i nterface ac characteristic ................................................... ...................................14 2.7 r egister i nformation ................................................... ................................................... .......................14 2.8 s tand - by mode ................................................... ................................................... ...................................19 2.9 b acklight d riving c onditions ................................................... ................................................... .........19 3. optical specification .............................. ................................................... .............................................20 4. reliabiilty test items............................... ................................................... .............................................22 5.touch screen panel specifications ................. ................................................... ...............................23 1. fpc p in a ssignment ................................................... ................................................... ............................23 2. e lectrical c haracteristics ................................................... ................................................... ..............23 3. m echanical c haracteristics ................................................... ................................................... .............23 4. l ife test c ondition ................................................... ................................................... .............................24 5. a ttention ................................................... ................................................... .............................................25 6. packing form..................................... ................................................... ................................................... ....26 7. suggested application note ........................... ................................................... ..................................27 1. a pplication c ircuit ................................................... ................................................... .............................27 2. p ower o n /o ff s equence ................................................... ................................................... ...................29 3. r ecommended r egister s etting ................................................... ................................................... .......31 4. g amma v oltage (tbd)............................................... ................................................... .............................32 www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 4 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. g eneral d escription a081vw01 is a amorphous transmissive type tft (thin film transistor) lcd (liquid crystal display). this model is composed of tft-lcd, drive ic, fpc (flexible printed circuit), backlight and touch panel. this model is the new driving type for 800rgbx300 application.the timing controller and one dcdc controller are integrated inside ic. it is easily to design for consumer product. features 8.1-inch display size with aspect ration of 8:3 resolution 800rgb x 300 in stripe dot arrangement 16.7m color supported paralle 24 / 18-bit rgb interface sicc ( s mart i ntegration c ascade c hip). support below functions vcom dc value adjustable sync timing adjustable built in timing controller and one dc-dc controller request 180ma for led blacklight standby mode supported 3-wire register setting low power consumption rohs compliant green design www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 5 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 1. general information no. item unit specification remark 1 display resolution dot 800rgb(h)300(v) 2 active area mm 192 (h)72(v) 3 screen size inch 8.1 (diagonal) 4 dot pitch mm 0.24(h) 0.24(v) 5 color configuration -- r. g. b. stripe note 1 6 color depth -- 16.7m colors note 2 7 overall dimension mm 204.6(h)x 86.2(v)x 8.23(t) note 3 8 weight g tbd (typ.) 9 panel surface treatment -- hard coating 10 display mode -- normally white note 1: below figure shows dot stripe arrangement. note 2: the full color display depends on 24-bit data signal (pin 4~27). note 3: not include fpc. refer next page to get further information. r g b r g b r g b r g b r g b . . ( 1 2 3 .2398 2399 2400) (1 .. 300 ) www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 6 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. assignment x l y h y l 2 1 3 4 pin no. x h 3 5 4 6 x2 x3 x3 2 1 y h x h y l x l x2 x2 x3 x4 8.1inch module outline dimension C front view www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 7 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 8.1inch module outline dimension C back view www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 8 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 2. electrical specifications 2.1 fpc pin assignment (hrs fh27-60h-0.4sh) pin no symbol i/o description remark 1 agnd2 p analog ground 2 avdd2 p analog power 3 vdd p digital power 4 r0 i data input (lsb) 5 r1 i data input 6 r2 i data input 7 r3 i data input 8 r4 i data input 9 r5 i data input 10 r6 i data input 11 r7 i data input (msb) 12 g0 i data input (lsb) 13 g1 i data input 14 g2 i data input 15 g3 i data input 16 g4 i data input 17 g5 i data input 18 g6 i data input 19 g7 i data input (msb) 20 b0 i data input (lsb) 21 b1 i data input 22 b2 i data input 23 b3 i data input 24 b4 i data input www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 9 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 25 b5 i data input 26 b6 i data input 27 b7 i data input (msb) 28 dclk i data clock input 29 de i data enable signal (de mode is with higher prority than hv mode.) 30 hsync i horizontal sync input. negative polarity 31 vsync i vertical sync input. negative polarity 32 scl i serial communication clock input 33 sda i serial communication data input 34 csb i serial communication chip select 35 nc do not connect (please leave it open) 36 vdd p digital power 37 nc do not connect (please leave it open) 38 gnd p digital ground 39 agnd p analog ground 40 avdd p analog power 41 vcomin i for external vcom dc input (optional) refer to r1(d7,d6) 42 nc do not connect (please leave it open) 43 nc do not connect (please leave it open) 44 vcom i for external vcom dc input (optional) refer to r1(d7,d6) 45 v10 p gamma correction voltage reference 46 v9 p gamma correction voltage reference 47 v8 p gamma correction voltage reference 48 v7 p gamma correction voltage reference 49 v6 p gamma correction voltage reference 50 v5 p gamma correction voltage reference 51 v4 p gamma correction voltage reference www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 10 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 52 v3 p gamma correction voltage reference 53 v2 p gamma correction voltage reference 54 v1 p gamma correction voltage reference 55 nc do not connect (please leave it open) 56 vgh p positive power for tft 57 vgl p negative power for tft 58 gvcc p digital power 59 ggnd p digital ground 60 cap c capacitor connect pin i : input, o : output, p : power, c: capacitor 2.2 absolute maximum ratings item symbol condition min. max. unit remark vdd gnd=0 -0.5 5 v note 1 gvcc ggnd=0 -0.5 5 v note 1 power voltage avdd agnd=0 -0.5 15 v note 1 operating temperature topa -- 0 60 ambient temperature storage temperature tstg -- -25 80 ambient temperature note 1: functional operation should be restricted under normal ambient temperature. www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 11 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 2.3 electrical characteristics the following items are measured under stable condi tion and suggested application circuit. 2.3.1. tft- lcd typical operation condition item symbol min. typ. max. unit remark vdd 3.2 3.3 3.6 v pin3 and pin36 avdd (10.5) (11) (11.5) v pin2 and pin40 gvcc 3.2 3.3 3.6 v pin58 vgh (14) (15) (16) v pin56 power supply vgl (-7.5) (-7) (-6.5) v pin57 h level v ih 0.7v cc - v cc v input signal l level v il gnd - 0.3v cc v vcom v cdc (4.3) (4.5) (4.7) v dc component i vdd 11 20 ma pin3 + pin36 i avdd 8 15 ma pin2 + pin40 i gvcc 0.02 0.1 ma pin58 i vgh 0.2 0.3 ma pin56 input current i vgl 0.2 0.3 ma pin57 note: above every operation range is based on stabl e operation from suggested application circuit note: typical current test pattern 2.4 ac characteristics parameter symbol conditions min. typ. max. unit clock high time t wcl 8 - - ns clock low time t wch 8 - - ns clock rising time t rclk - - 1 ns clock falling time t ack - - 1 ns hsync setup time t hsu 5 ns hsync hold time t hhd 10 ns vsync setup time t vsu 0 ns vsync hold time t vhd 2 ns data setup time t dsu 5 ns www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 12 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. parameter symbol conditions min. typ. max. unit data hold time t dhd 10 ns data enable set-up time t esu 4 ns data enable hold time t ehd 2 ns hs vs t vpd vih vih vil vil clk rgb, de, hs t ds, t es, t hs vih vih vil vil t dh, t he, t hh t ch t cl 2.5 rgb parallel input timing horizontal timing parameter symbol conditions min. typ. max unit dclk frequency f dclk 22 24 27.5 mhz dclk period t dclk 36.4 41.7 45.5 ns hsync period (= t hd + t hbl ) t h 986 1056 1183 dclk active area t hd - 800 - dclk horizontal blanking (= t hf + t he ) t hbl 186 256 383 clk hsync front porch t hf 40 - clk delay from hsync to 1 st data input (= t hw + t hb ) t he function of hdl[5..0] settings 146 216 343 dclk hsync pulse width t hw 1 128 136 clk hsync back porch t hb 10 88 342 clk vertical timing parameter symbol conditions min. typ. max. unit vsync period (= t vd + t vbl ) t v 372 380 387 th active lines t vd 300 th vertical blanking (= t vf + t ve ) t vbl 72 80 87 th vsync front porch t vf - 17 - th gd start pulse delay t ve function of vdl[3..0] settings 55 63 70 hs vsync pulse width t vw 1 2 20 th hsync/ vsync phase shift t vpd 2 320 - clk www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 13 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. hs r[7:0] g[7:0] b[7:0] r0 g0 b0 r1 g1 b1 r2 g2 b2 r3 g3 b3 t h t hw t hb t hf t he r n-1 g n-1 b n-1 r n g n b n invalid invalid invalid invalid invalid invalid r n g n b n r n-1 g n-1 b n-1 t hbl t hd dclk figure 4 : horizontal input timing. (hv mode) dclk de t hbl t hd r[7:0] g[7:0] b[7:0] r0 g0 b0 r1 g1 b1 r2 g2 b2 r3 g3 b3 r n-1 g n-1 b n-1 r n g n b n invalid invalid invalid invalid invalid invalid r n g n b n r n-1 g n-1 b n-1 figure 5 : horizontal input timing. (de mode) vs hs line t vw xn-1 xn x1 x2 x3 xn-1 xn t v t vf t ve t vbl t h t vf invalid t vd figure 6 : vertical timing. (hv mode) de line xn-1 xn x1 x2 x3 xn-1 xn t vbl invalid t vd figure 7 : vertical timing. (de mode) www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 14 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 2.6 serial control interface ac characteristic parameter symbol conditions min. typ. max. unit serial clock t sck 320 ns scl pulse duty t scw 40 50 60 % serial data setup time t ist 120 ns serial data hold time t ihd 120 ns serial clock high/low t ssw 120 ns csb setup time t cst 120 ns csb hold time t chd 120 ns chip select distinguish t cd 1 us delay from csb to vsync t cv 1 us d15 d14 d13 d2 d1 d0 d15 d14 d13 d12 scl sda csb vsync t cst t ist t ihd t ssw t ssw t sck t chd t cd t cv 30% 30% 30% 30% 70% 30% 70% figure 2 : ac serial interface write mode timing 2.7 register information there is a total of 5 registers each containing several parameters. for a detail ed description of the parameters refer to table 1 .the serial register has read/write function. d[15:12] are the register address , d[11] defines the read or write mode and d[10:0] are the data. figure 1: serial interface write sequence www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 15 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 1. at power-on, the default values specified for each parameter (in table 1 ) are taken. 2. if less than 16-bit data are read during the cs low time period, the data is cancelled. a. the write operation is cancelled. 3. all items are set at the falling edge of the vertical sync, except r 0[1:0]. 4. when grb is activated through the serial interface, all registers are c leared, except the grb value. 5. register w setting: d11 = l write mode; 6. the register setting values are valid when vcc already goes to high and after vsync starts. 7. it is suggested that vsync, hsync, dclk always exists in t he same time. but if hsync, dclk stops, only vsync operating, the register setting is still v alid. 8. if the chip goes to standby mode, the register value will still keep. mc u can wake up the chip only by changing standby mode value from low to high. 9. the register setting values are rewritten by the influence of static elect ricity, a noise, etc. to unsuitable value, incorrect operating may occur. it is suggested that the spi interface will setup as frequently as possible. 2.7.1 register table (default register settings) address w data reg no . d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 r0 0 0 0 0 0 01 01 1 u/d (0) shl (1) shdb1 (1) x grb (1) stb (1) r1 0 0 0 1 0 x 01 vcom_m (01) vcom_lvl (2fh) r2 0 0 1 0 0 x x x hdl (80h) r3 0 0 1 1 0 x x 0 0 0 0 0 vdl (1000) r4 0 1 0 0 0 x x 0 0 00 1 1111 r6 0 1 1 0 0 x 0 engb12 (1) engb11 (1) engb10 (1) 0 0 engb5 (1) engb4 (1) engb3 (1) 0 r4 should be set to 411fh x : reserved, please set to 0. 2.7.2 r0 settings address bit description default 0000 [10..0] bits 10-9 auo internal use 01 bits 7-8 auo internal use 01 bit6 auo internal use 1 bit5 (u/d) vertical shift direction selection. 0 bit4 (shl) horizontal shift direction selection. 1 www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 16 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. bit3 (shdb1) avdd dc-dc converter shutdown setting. 1 bit2 auo internal use 0 bit1 (grb) global reset. 1 bit0 (stb) standby mode setting. 1 bit5 u/d function 0 scan down; first line=gn gn-1 g2 last line=g1. (default) 1 scan up; first line=g1 g2 gn-1 last line=gn. bit4 shl function 0 shift left; first data=y600 y601 y2 last data=y1. 1 shift right: first data=y1 y2 y600 last data=y600. (default) bit3 shdb1 function 0 avdd dc-dc converter is off. 1 avdd dc-dc converter is on. (default) bit1 grb function 0 the controller is reset. reset all registers to default value. 1 normal operation. (default) bit0 stb function 0 t-con, source driver and dc-dc converters are off, and all outputs are high-z. 1 normal operation. ( default) r1 settings address bit description default 0001 [8..0] bit9-8 auo internal use 01 bit7-6 (vcom_m) vcom mode signal. 01 bit5-0 (vcom_lvl) vcom level adjustment. step 31.25mv/lsb @avdd=12.5v (avdd/400) 2fh bit7-6 vcom_m function. 00 vcom generator disabled. vcom is generated externally. www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 17 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 01 vcom internal reference disabled. dc voltage of vcom follows vcomin signal. ( default ) 1x vcom generator enabled. dc voltage of vcom follows vcom_lvl settings. note: please refer to to following figure. (coma is panel internal si gnall) bit5-0 vcom_lvl function @v1=12.5v 00h vcom_lvl = v1/2C47*31.25mv = 4.78125v 01h vcom_lvl = v1/2C46*31.25mv = 4.8125v 2fh vcom_lvl = v1/2 = 6.25v ( default ) 3eh vcom_lvl = v1/2+15*31.25mv = 6.71875v 3fh vcom_lvl = v1/2+16*31.25mv = 6.75v r2 settings address bit description default 0010 [7..0] bit7-0 (hdl) horizontal start pulse adjustment function 80h bit7-0 hdl function. 00h t he = t hetyp C 128 clk period. 80h t he = t hetyp . (default) ffh t he = t hetyp + 127 clk period. www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 18 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. r3 settings address bit description default 0011 6..0] bit6 auo internal use 0 bit5 auo internal use 0 bit4 auo internal use 0 bit3-0 (vdl) vertical start pulse adjustment function 1000 bit3-0 vdl function. 0000 t ve = t vetyp C 8 hs period. 0001 t ve = t vetyp C 7 hs period. 0010 t ve = t vetyp C 6 hs period. 0011 t ve = t vetyp C 5 hs period. 0100 t ve = t vetyp C 4 hs period. 0101 t ve = t vetyp C 3 hs period. 0110 t ve = t vetyp C 2 hs period. 0111 t ve = t vetyp C 1 hs period. 1000 t ve = t vetyp . (default) 1001 t ve = t vetyp + 1 hs period. 1010 t ve = t vetyp + 2 hs period. 1011 t ve = t vetyp + 3 hs period. 1100 t ve = t vetyp + 4 hs period. 1101 t ve = t vetyp + 5 hs period. 1110 t ve = t vetyp + 6 hs period. 1111 t ve = t vetyp + 7 hs period. r6 settings address bit description default 0110 [9..0] bit9 auo internal use 0 bit8(engb12) gamma buffer enable for v9 1 bit7(engb11) gamma buffer enable for v8 1 bit6(engb10) gamma buffer enable for v7 1 bit5 auo internal use 0 bit4 auo internal use 0 bit3(engb5) gamma buffer enable for v4 1 bit2(engb4) gamma buffer enable for v3 1 bit1(engb3) gamma buffer enable for v2 1 bit0 auo internal use 0 www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 19 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. bitx engbx function 0 gamma buffer for vx is disable (high z). 1 gamma buffer is enable. vx must be connected externally. 2.8 stand-by mode 2.9 backlight driving conditions parameter symbol min. typ. max. unit remark led current i l --- (180) (200) ma --- led voltage v l --- 13.2 --- v --- led life time l l 10,000 --- --- hr note 2, 3 note 1: led backlight is four leds serial type. note 2 :define led lifetime: brightness is decreased to 50% of the initial v alue. led lifetime is restricted under normal condition, ambient temperature = 25 and led current = 180ma. note 3: if it uses larger led current i l more than 200ma, it maybe decreases the led lifetime. www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 20 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 50 cm | ------------------------------- | 90 3. optical specification item symbol condition min. typ. max. unit remark response time rise fall tr tf =0 - - 10 20 50 60 ms ms note 3 contrast ratio cr at optimized viewing angle 250 300 - note 4 viewing angle top bottom left right cr 10 R 35 55 55 55 40 60 60 60 - - - - deg. note 5 brightness (w/ tp) y l =0 250 300 - cd/m 2 note 6 x =0 0.26 0.31 0.36 white chromaticity y =0 0.28 0.33 0.38 note 1 : ambient temperature =25 , and l amp current i l = 180 ma. to be measured in the dark room. note 2 :to be measured on the center area of panel with a viewing cone of 1 by topcon luminance meter bm-7, after 15 minutes operation. note 3. definition of response time: the output signals of photo detector are measured when the input signals are changed from black to white(falling time) and from white to black(rising time), respectiv ely. the response time is defined as the time interval between the 10% and 90% of amplitudes. refer to figure as below. s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" "white" 0% 10% 90% 100% www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 21 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. note 4. definition of contrast ratio: contrast ratio is calculated with the following formula. contrast ratio (cr)= note 5. definition of viewing angle, , refer to figure as below. note 6. measured at the center area of the panel when all the input terminals of lcd panel are electrically opened. photo detector output when lcd is at white state photo detector output when lcd is at black state www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 22 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 4. reliabiilty test items no. test items conditions remark 1 high temperature storage ta = 80 240hrs 2 low temperature storage ta = -25 240hrs 3 high temperature operation ta = 60 240hrs 4 low temperature operation ta = 0 240hrs 5 high temperature and high humidity ta = 60 . 90% r h 240hrs operation 6 heat shock -25 ~80 , 50 cycles, 2hrs/cycle non-operation 7 electrostatic discharge 200v,200pf (0?), once for each terminal non-operation 8 vibration (with carton) random vibration: 0.015g 2 /hz from 5~200hz iec 68-34 9 drop (with carton) height: 60cm 1 corner, 3 edges, 6 surfaces note 1: ta: ambient temperature. www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 23 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 5.touch screen panel specifications 1. fpc pin assignment pin no. symbol i/o 1 xl o 2 yl o 3 xh o 4 yh o 2. electrical characteristics item min. max. unit remark rate dc voltage 7 v standard 5v x (film) 400 1600 resistance y (glass) 100 400 ? at connector linearity -1.5% 1.5% -- note 1, test by 150 gf chattering 30 ms at connector pin insulation resistance 20m ? dc 25v note 1: measurement condition of linearity: difference between actual voltage & theor etical voltage is an error at any points. linearity is the value max. error voltage divided by voltage difference on active area. 3. mechanical characteristics item min. max. unit remark hardness of surface 3 -- h jis k-5400 operation force (pen or finger) -- 80 gf note 1 note 1: within guaranteed active area, but not on the edge and dot-spacer. www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 24 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 4. life test condition item min. max. unit remark sliding life 10 5 -- times note 1, 2 input life 10 6 -- times note 1, 3 note 1: measurement condition of operation force: within guaranteed active area. resistance, insulation resistance, and operation force should be under 5.2 & 5.3 condition. when user pushes d o w n o n t h e f i l m , r e s i s t a n c e b e t w e e n x & y a x i s m u s t b e e q u a l o r l o w e r t h a n 2 k ? . b e l o w i s t e s t figure. note 2: sliding life test condition (by pen): sliding area for pen slid ing life test is the center of active area, 20x20 mm.sliding speed is 100mm/s. note 3: input life test condition( by finger): by silicone rubber tappi ng at center of active area. tapping load is 250g, and tapping frequency is 3 hz. www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 25 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 5. attention please pay attention for below matters at mounting design of touch panel of lcd module. 1. do not design enclosure pressing the view area to prevent from miss input. 2. enclosure support must not touch with view area. 3. use elastic or non-conductive material to enclosure touch panel. 4. do not bond film of touch panel with enclosure. 5. the touch panel edge is conductive. do not touch it with any conductive part after mounting. 6. if user wants to cleaning touch panel by air gun, pressure 2kg/cm2 below is suggested. not to blow glass from fpc site to prevent fpc peeled off. 7. do not put a heavy shock or stress on touch panel and film surface. ex. don t lift the panel by film face with vacuum. 8. do not lift lcd module by fpc. 9. please use dry cloth or soft cloth with neutral detergent (after wring dry) or one with ethanol at cleaning. do not use any organic solvent, acid or alkali liquor. 10. do not pile touch panel. do not put heavy goods on touch panel. recommendation of the cushion area: www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 26 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 6. packing form a u o a u o a u o a u o a u o a u o bend side to back www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 27 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transforme d to any other forms without permission from au optronics corp. 7. suggested application note 1. application circuit c414 1uf/35v/x5r/0603 r417 10k/1%/0603 r427 110k/1%/0603 r419 0/5%/0603 c421 0.1uf/25v/x5r/0603 r432 0/5%/0603 +10v fb_2 c425 0.1uf/25v/x5r/0603 r414 6.8k/5%/0603 r424 0/5%/0603 c428 27pf/50v/x5r/0603 l402 cxlp100-100(10uh) cxlp100 5v c418 10uf/10v/x5r/0805 c430 22uf/16v/x5r/1206 3.3v d404 sb07-03c 1 3 2 c415 0.1uf/25v/x5r/0603 r426 10k/1%/0603 r418 10k/1%/0603 r421 10/1%/0603 avdd2 dm405 dan217u 2 1 3 k a c +15v vgl2 c420 22nf/50v/x5r/0603 c423 27pf/50v/x5r/0402 c417 0.1uf/10v/x5r/0402 r431 5.1k/5%/0603 r412 0/5%/0603 vgh2 c413 0.1uf/25v/x5r/0603 fb_1 r415 no(0/5%/0603) 3.3v r429 10/1%/0603 fb_3 dm408 dan217u 2 1 3 k a c c422 2.2uf/35v/x5r/0805 u401 mp1530 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 /rdy fb1 comp in gnd ref fb2 fb3 ct sw pgnd in3 gh in2 gl en r433 261/5%/0603 r425 70k/1%/0603 c416 2.2uf/35v/x5r/0805 d405 no(rb551v-30) 1 2 r420 56k/1%/0603 c424 0.1uf/25v/x5r/0603 r422 0/5%/0603 r416 0/5%/0603 dm407 dan217u 2 1 3 k a c c427 2.2uf/35v/x5r/0805 dm406 dan217u 2 1 3 k a c -7v r423 5.1k/1%/0603 r428 0/5%/0603 r430 0/5%/0603 en r413 100k/5%/0603 c426 1uf/35v/x5r/0603 c429 2.2uf/25v/x5r/0805 c419 10nf/50v/x5r/0603 www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 28 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transforme d to any other forms without permission from au optronics corp. vgh scl csb g6 r7 b7 r0 b1 dgnd 3.3v b5 r6 v8 v3 r2 sda r4 v6 g5 b4 g4 de v9 v4 3.3v r3 g1 dgnd g0 vcomin g3 r1 c505 10uf/10v/x5r/k/0805 b3 b6 avdd avdd b0 v1 v7 b2 g2 v10 dgnd vs r5 vcom hs v2 v5 g7 dclk 3.3v r316 0/5%/0603 v4 r307 370/1%/0603 c306 1uf/16v/x5r/0603 r301 1k/1%/0603 avdd v3 r324 0/5%/0603 c302 0.1uf/16v/x5r/0402 v10 vr301 evm3rsx50b14 c323 0.1uf/16v/x5r/k/0402 avdd c307 1uf/16v/x5r/0603 r325 0/5%/0603 r310 0/5%/0603 r323 0/5%/0603 r322 0/5%/0603 c308 1uf/16v/x5r/0603 r308 0/5%/0603 vcom r321 1k/1%/0603 c305 1uf/16v/x5r/0603 r314 0/5%/0603 c309 1uf/16v/x5r/0603 c303 1uf/16v/x5r/0603 v6 v5 v1 r311 2.4k/1%/0603 r305 530/1%/0603 r302 0/5%/0603 v8 3 4 2 5 1 + - u301a no(ad8565) c310 1uf/16v/x5r/0603 r315 370/1%/0603 c506 10uf/10v/x5r/k/0805 r320 0/5%/0603 v2 r306 0/5%/0603 v9 c311 1uf/16v/x5r/0603 vcomin v7 r318 0/5%/0603 r515 0/5%/0603 c322 1uf/16v/x5r/0603 r309 700/1%/0603 avdd r313 700/1%/0603 r317 530/1%/0603 r312 0/5%/0603 c304 1uf/16v/x5r/0603 r319 1.7k/1%/0603 c324 10uf/10v/x5r/k/0805 r303 1.7k/1%/0603 r304 0/5%/0603 r516 no(0/5%/0603) c301 10uf/16v/x5r/1206 vgl vcom agnd2 1 avdd2 2 vdd 3 r0 4 r1 5 r2 6 r3 7 r4 8 r5 9 r6 10 r7 11 g0 12 g1 13 g2 14 g3 15 g4 16 g5 17 g6 18 g7 19 b0 20 b1 21 b2 22 b3 23 b4 24 b5 25 b6 26 b7 27 dclk 28 de 29 hsy nc 30 vsy nc 31 scl 32 sda 33 csb 34 nc 35 vdd 36 nc 37 gnd 38 agnd 39 avdd 40 vcomin 41 nc 42 nc 43 vcom 44 v10 45 v9 46 v8 47 v7 48 v6 49 v5 50 v4 51 v3 52 v2 53 v1 54 nc 55 vgh 56 vgl 57 gvcc 58 ggnd 59 cap 60 j502 con60 www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 29 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 2. power on/off sequence this ic may be damaged by a large current flow when an incorrect power sequence is applied. the recommended power-on sequence is to first connect the logical power (vc c&gnd), then the analog and driver powers (avdd&agnd) and finally the references v1~14. when shutting off t he power, the inverse sequence should be applied or all power should be turned off simultaneously. power on sequence vcc gnd vcc 90% 0% led gnd vled 0% avdd vgl vgh gnd gnd gnd avdd vgl vgh vcc 90% 90% 0% 0% 0% serial interface 90% > 100us 90% > 0us > 50us 0% 0% 0% 90% vsync digital input gnd vcc vcc gnd gnd > 0us > 0us > 80ms 90% > 100us 90% > 1ms www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 30 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. power off sequence vcc gnd vcc 90% 0% led gnd vled 90% 0% avdd vgl vgh gnd gnd gnd avdd vgl vgh vcc 90% 0% serial interface > 10us 0% 100% vsync digital input gnd vcc vcc gnd gnd > 0us >80ms 90% 90% 90% 0% 0% 0% 0% 90% > 0us note : use external dcdc controller for avdd, vgl, and vgh. www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 31 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. 3. recommended register setting address w data reg no . d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 r0 0 0 0 0 0 0 0 01 1 0 1 0 0 1 1 r1 0 0 0 1 0 0 01 01 2fh r4 0 1 0 0 0 0 0 1 0 00 1 1111 r4 should be set to 411fh use vcom(pin44) as input , r1 should be setted to 112fh use vcomin(pin41) as input , r1 should be setted to 116fh www.datasheet.co.kr datasheet pdf - http://www..net/
sample: for es7 or later version: 0.8c page: 32 / 32 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permissio n from au optronics corp. avdd 1k/1%/0603 1.7k/1%/0603 530/1%/0603 2.4k/1%/0603 700/1%/0603 370/1%/0603 v1 v2 700/1%/0603 1.7k/1%/0603 530/1%/0603 370/1%/0603 1k/1%/0603 v5 v4 v3 v6 v7 v8 v9 v10 4. gamma voltage (tbd) gamma 2.2 avdd (11) 00h v1 (10) 10h v2 (8.3) 20h v3 (7.77) 30h v4 (7.4) 3fh v5 (6.7) 3fh v6 (4.3) 30h v7 (3.6) 20h v8 (3.23) 10h v9 (2.7) 00h v10 (1) www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of A081VW01-V0

	To Download A081VW01-V0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .