50w solid state bucs cpi solid inside and out 811 hansen way p.o. box 51625, palo alto, ca 94303 tel: +1 (650) 846-3803 fax: +1 (650) 424-1744 e-mail: satcommarketing@satcom.cpii.com www.cpii.com/satcom cpi-built rf brick inside with cpi-built rf brick inside and plenty of thermal margin, this sspa is rock-solid, highly ef cient and easy to maintain. high linearity excellent am/pm, phase noise and spectral regrowth performance. simple to operate user-friendly microprocessor-controlled logic with both integrated serial (rs-232 and rs-422/485) and ethernet computer interfaces. also contains digitally controlled attenuator. extended band operation provides 45 watts of p1db output power at the ange over the entire 13.75 to 14.50 ghz frequency range. model B3UO 50 watt ku-band solid state block upconverters ? environmentally sealed compact design for outdoor operation global applications perfect for satcom on the move, micro flyaway systems, vsats, and antenna- mount applications. meets international safety standard en -60950, electromagnetic compatibility 89/336/eec and harmonic standard en-61000-3-2 to satisfy worldwide requirements. worldwide support backed by over three decades of satellite communications experience, and cpi?s worldwide 24-hour customer support network that includes sixteen regional factory service centers. 50w solid state bucs ku-band ku-band
ku-band for more detailed information, please refer to the corresponding cpi technical description. note: speci cations may change without notice as a result of additional data or product re nement. please contact cpi before using this information for system design. mkt 193, issue 17 2/09 pdf options: ? 14.0 - 14.5 ghz operation ? front panel display certificate number: 30515 specifications, 50 w ku-band outdoor solid state buc (model B3UO) electrical frequency 13.75 to 14.50 ghz l-band input 950 to 1700 mhz output power 50w (47.0 dbm) psat 45w (46.5 dbm) p1db local oscillator frequency 12,800 mhz or 13,050 mhz (select either) internal 10 mhz reference standard small signal gain 70 db min. (higher gain options available) gain stability over temp., constant drive ?.0 db over oper. temp. range over 24 hours, xed temp. ?.25 db gain slope ?.04 db/mhz max. small signal gain variation across any 80 mhz band ?.85 db pk-pk max. across the full band ?.25 db gain adjustment range 17 db input vswr 1.5:1 max. (50 ohms) output vswr 1.3:1 max. load vswr continuous operation 2.0:1 full spec compliance 1.5:1 residual am, max. -80 dbc > 100 khz from carrier phase noise, max. 100 hz -63 dbc/hz 1 khz -73 dbc/hz 10 khz -83 dbc/hz 100 khz -93 dbc/hz 1 mhz -103 dbc/hz am/pm conversion 2.5?db max. for a single-carrier at 2.5 db backoff from p1db harmonic output -60 dbc max. at p1db spurious response at p1db -60 dbc max. in band intermodulation distortion -25 dbc max. with two equal carriers and 5 mhz apart at 3.0 db total backoff from p1db group delay 0.03 ns/mhz linear max. (in any 80 mhz band) 0.003 ns/mhz 2 parabolic max. 1.0 ns pk-pk ripple max. primary power single phase, 100-250 vac ?0% 47-63 hz power consumption 428 va typ. power factor 0.95 min. monitor and control remote control transmit on/off fault reset attenuator setting computer/network interface rs-232c, 422/485 and ethernet remote status transmit on/off, summary fault temperature, fault identi cation rf inhibit (on/off), lock detect environmental ambient temperature -4 0? to +60? operating, solar loading immune; -50? to +85? non-operating relative humidity 100% condensing altitude 12,000 ft. with standard adiabatic derating of 2?/1000 ft., operating; 50,000 ft., non-operating cooling integral forced air shock and vibration 20 g peak, 11 msec, 2 sine; 2.1 g rms , 5 to 500 hz. mechanical rf output connection wr-75 waveguide ange, grooved with unc 2b 6-32 threaded holes l-band input connection type n female m&c connection 12 pin circular (lf10wbr-12s) dimensions 6 x 6 x 16 in. (142 x 142 x 406 mm) weight 25 lbs (11.4 kg) typ.
|
