View LS013B4DN01_5946747.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

96 96 silver reflective pnlc memory lcd module featuring zebra (elastomeric) connector, 50% reflectivity with 10:1 contrast. LS013B4DN01 lcd module preliminary product specification april 2009 lcd specification lcd group technical document
technical literature for tft-lcd module model no. LS013B4DN01 notice mobile liquid crystal display group sharp corporation no. lcy-12t09302a date april. 24 th 2009 the technical literature is subject to change without any prior notice for the purpose of product improvement. please contact sharp or its representative before designing your product based on this literature.
spec no. lcy-12t09302a model no. LS013B4DN01 page 1 << precautions>> notice these specification sheets are the propri etary product of sharp corporation ("sharp") and include materials protected under copyright of sharp. do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of sharp. the application examples in these specifi cation sheets are provided to explain the re presentative applications of the device a nd are not intended to guarantee any industrial property right or other rights or license you to use them. sharp assumes no responsibility for any problems related to any industrial propert y right of a third party resulting from the use of the device. sharp reserves the right to make changes in the specifications, characteristics, data, materials, structures and other contents described herein at any time without notice in order to improve design or reliability. contact sharp in order to obtain the lat est specification sheets before using any sharp' s device. manufacturing locations are also subject to change without notice. observe the following points when in using any device in this publication. sharp takes no responsibility for damage caused by improper use of the devices. the devices in this publication are designed for use in general electronic equipment designs, such as: ? personal computers ? office automation ? telecommunication equipment ? test and measurement equipment ? industrial control ? audio visual and multimedia equipment ? consumer electronics the appropriate design measures should be taken to en sure reliability and safety when sharp's devices are used for equipment such as: ? transportation control and safety equipmen t(i.e.,aircraft,trai ns,automobiles,etc.) ? traffic signals ? gas leakage sensor breakers ? alarm equipment ? various safety devices etc. sharp's devices shall not be used for equipment that requires extremely high level of reliability, such as: ? military and space applications ? nuclear power control equipment ? medical equipment for life support sharp assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions speci fied in these specification sheets. contact and consult with a sharp sales repres entative for any questions about this device. .
spec no. lcy-12t09302a model no. LS013B4DN01 page 2 [for handling and system design] (1) it is recommended to handle lcd panel with carefully, since this lcd panel is made of thin glass, dropping the module or banging it against hard objects may cause cracks or fragmentation. (2) do not scratch the surface of the uv protection film as it is easily damaged. (3) water droplets on the uv protection film must be wiped off immediately as they may cause color changes, or other defects if remained for a long time. (4) if the cleaning of the surface of the lcd panel is necessa ry, wipe it swiftly with cotton or other soft cloth. do not use organic solvents as it damages the uv protection film. (5) do not hold or touch the part of single glass of lcd pane l which has electric connection area, as electric circuits in lcd panel may be damaged. (6) hold lcd with very carefully when plac ing lcd module into the system housing. (7) lcd panel is susceptible to mechanical stress and even the slightest stress will cause a color change in background. so mak e sure the lcd panel is placed on fl at plane without any continuous tw isting, bending or pushing stress. (8) when carrying the lcd module, place it on the tray to protect from mechanical damage. it is recommended to use the conductive trays to protect lcd panel from electrostatic discharg e. certain materials such as ep oxy resin (amine?s hardener) or silicone adhesive agent (de-alcohol or de-oxym) emits gas to which the uv protection fi lm reacts (color change). check carefully that gas from materials used in system housing or packaging do not hart the uv protection film. (9)do not apply excessive stress or pressure to lcd module. do not to use chloropren e rubber as it may affect on the reliabilit y of the electrical interconnection. (10) as this lcd module contai ns components sensitive to electrostatic discharg e, more than 200v, be sure to follow the instructions in below. operators operators must wear anti-static wears to prevent electro static charge up to and discharge from human body. equipment and containers process equipment such as conveyer, soldering iron, working bench and containers may possibly generate electrostatic charge up and discharge. equipment must be grounded through 100mohms resistance. use ion blower. floor floor is an important part to leak static electric ity which is generated from human body or equipment. there is a possibility that the static el ectricity is charged to them without le akage in case of insulating floor, so the electrostatic earth should be lower than the 1 10 8 . humidity proper humidity of working room may reduce the risk of electrostatic charge up and discharge. humidity should be kept over 50% all the time. transportation/storage storage materials must be anti-static to prevent causing electrostatic discharge. others (11) protective film is attached on the surface of the uv protec tion film on lcd panel to prevent scratches or other damages. when removing this protective film, remove it slowly under proper anti-esd cont rol such as ion blower.
spec no. lcy-12t09302a model no. LS013B4DN01 page 3 [for operating lcd module] (1) do not operate the lcd panel under outside of electri cal specification. otherwise lcd panel may be damaged. (2) do not operate the lcd panel under outside of specified driving timing chart. otherwise lcd panel may not have proper picture quality. (3) a still image should be displayed less th an two hours, if it is necessary to disp lay still image longer than two hour, disp lay image data must be refreshed in order to avoid sticking image on lcd panel. [precautions for storage] (1) do not expose the lcd module to dir ect sunlight or strong ultraviolet light for long periods. store in a dark place. (2) the liquid crystal material will solidify if stored below the rated storage temperature and will become an isotropic liquid if stored above the rated storage temperature, and may not retain its original properties. only store the module at normal temperature and humidity (25 5c,60 10%rh) in order to avoid exposing the uv protection film to chronic humidity. (3) keeping method a. don't keeping under the direct sunlight. b. keepin g in the tray under the dark place.
spec no. lcy-12t09302a model no. LS013B4DN01 page 4 [other notice] (1) do not operate or store the lcd module under outside of specified environmental conditions. (2) as electrical impedance of power supply lines (vdd-vss) are low when lcd module is working, place the de-coupling capacitor near by lcd module as close as possible. (3) although the lcd panel has th e uv protection film on the lcd panel surface, ju st in case, do not expose the lcd module to direct sunlight or strong ultraviolet light for long periods. (4) do not disassemble the lcd module as it may cause permanent damage. (5) since the liquid crystal is injurious, do not put it into the eyes or mouth. when liquid crystal sticks to hands, feet or clothes, wash it out immediately with soap. (6) this lcd module does not contain nor use any ods (1,1,1-trichloroethane, ccl4) in all materials used, in all production processes. (7) observe all other precautionary requirements in handling general electronic components. [precautions for discarding liquid crystal modules] lcd panel: dispose of as glass waste. this lcd module contains no harmful substances. the liquid crystal panel contains no dangerous or harmful substances. the liquid crystal panel only contains an extremely small amount of liquid crystal (approx.100mg) and therefore it will not leak even if the panel should break. -its median lethal dose (ld50) is greater than 2,000 mg/kg and a mutagenetic (aims test: negative) material is employed.
spec no. lcy-12t09302a model no. LS013B4DN01 page 5 contents 1. outline ??????????????????????????????????????????????????????????????? ???????????? p6 2. characteristics ??????????????????????????????????????????????????????????????? ????? p6 3.mechanical specification ????????????????????????????????????????????????????????????? p6 4.input terminal specification ??????????????????????????????????????????????????????????? p7 5.absolute maximum rating ??????????????????????????????????????????????????????????? p8 6.electrical specification ??????????????????????????????????????????????????????????????? p8 7.optical chracteristics ??????????????????????????????????????????????????????????????? ? p18 8.lcd module outline dimensions ????????????????????????????????????????????????????? p20 9.external capacitor ??????????????????????????????????????????????????????????????? ????? p21 10.external power supply ??????????????????????????????????????????????????????????????? p22 11.zebra connector ??????????????????????????????????????????????????????????????? ????? p23 12.packaging ??????????????????????????????????????????????????????????????? ?????????? p24 13.reliability test ??????????????????????????????????????????????????????????????? ????? p26
spec no. lcy-12t09302a model no. LS013B4DN01 page 6 1. outline this tft-lcd module is a reflective active matrix memory liquid crystal display module with cg silicone thin film transistor. module outline is indicated in table 8-1. 2. characteristics ? reflective panel of white and black with aspect ratio of 1:1 ? 1.35? screen has 96x 96 resolusion.( 9216 pixels stripe array) ? display control by serial data signal communication. ? arbitrary line data renewable. ? 1bit internal memory for data storage within the panel. ? thin, light-weight and compact modu le with monolithic technology. ? super low power consumption tft panel. ? zebra connecter 3 mechanical specification table 3-1 item specification unit screen size 1.35 inch viewing area 24 (h) 24 (v) mm dot configuration 96 (h) 96 (v) dot dot pitch 0.252 (h) 0.252 (v) mm pixel array stripe array - outline dimension 28.2 (w) 32.34 (h) 1.4 (d) mm mass 3.6 (typ g surface hardness 3h pencil hardness note detail dimension and tolerance are shown in fig. 8-1
spec no. lcy-12t09302a model no. LS013B4DN01 page 7 4 input terminal names and functions table4-1 terminal symbol i o function remark 1 test1 - test terminal remark4-1 2 test2 - test terminal remark4-1 3 sclk input serial clock signal 4 si input serial data input signal 5 scs input chip select signal 6 extcomin input external com inversion signal input (h: enable) 7 disp input display on/off signal remark4-3 8 vdda power power supply (analog) 9 vdd power power supply (digital) 10 extmode input com inversion select terminal remark4-2 11 vss power gnd(digital) 12 vssa power gnd(analog) 13 test3 - test terminal remark4-1 14 test4 - test terminal remark4-1 remark4-1 test terminal: open these test terminals. remark4-2 when it?s ?h?, extcomin signal is enable. and when it?s ?l? ,serial input flag is enable. ?h?mode; connect the extmode tovdd, ?l? mode; connect the extmode to vss. remark4-3 the display on/off signal is only for display. data in the memory will be saved at the time of on/off. when it?s ?h?, data in the memory will di splay, when it?s ?l?, white color will diaplay and data in the memory will be saved. 4-2 recommended circuit;
spec no. lcy-12t09302a model no. LS013B4DN01 page 8 5 absolute maximum rating table5-1 gnd 0v item symbol min. max. unit remark analog vdda -0.3 5.8 v power supply voltage logic vdd -0.3 5.8 v [remark5-1] input signal voltage(high) vdd v [remark5-2] input signal voltage(low) -0.3 v strage temperature tstg -30 80 [remark5-3,4] operation temperature (at panel surface) topr1 -20 70 [remark5-5] [remark5-1] applies to extmode. [remark5-2] applies to sclk , si, scs, disp, extcomin. [remark5-3] do not exceed this temperature in any parts of module. [remark5-4] maximum wet bulb temperature is 57 or lower. no condensation is allowed. cndensation will cause electeical leak and may cause the module to not meet this specification. [remark5-5] operating temperature is the temp erature that guarantees only the operation. for contrast, response time, and other display quality determination, use ta 25 . 6 electrical characteristics 6-1 tft lcd panel drive table6-1 recommended operating condition vss(gnd) 0v ta 25 item symbol min. typ. max. unit remark analog vdda 4.8 5.0 5.5 v power supply logic vdd 4.8 5.0 5.5 v [remark6-1] hi vih 2.70 3.00 vdd v input signal voltage lo vil vss vss vss+0.15 v [remark6-2] hi ioh - - tbd ua [remark6-2] vi=3v input leak current lo iol - - tbd ua [remark6-2] vi=0v lower 3v is recommended, and it?s lower than the vdd voltage. [remark6-1] applies to extmode ?h? [remark6-2] applies to sclk , si, scs, disp, extcomin.
spec no. lcy-12t09302a model no. LS013B4DN01 page 9 6-2 power supply sequence [remark] precaustions at ehte time of power on and power off. remark 1)when power on , vddand vdda are same timem or vdd should be faster than the vdda. remark 2) when power off, vdd and vdda are same time or vdda shoud be faster than the vdd. ? ? 1 ? 1 ?? vdd/vdda (5v) gnd gn d disp gnd gn d extcomin gnd gn d scs gnd 2 2 gn d others gnd 2 2 gn d normal operation normal operation normal operation t1 off sequence normal operation detail description for signal timing is shown the digital timing chart and the ac timing chart. 1 the order of and can be set as being reversed, in this case, tcom polarity inversion timing which can be controlled by extcomin doesn't work during disp="l". 2 setup value for initialization of data within pixel memory to refer the timing chart of all clear mode section 6-5-4. t2 t3 t4 t5 t6 t7 on sequence [on sequence] * all on start up system 5v start up initializes me mory da ta within pixel t2 : more tha n 1v initialize with d2 "all cle a r flag" or display all white . to ca nce l la tch initia liza tion for tcom. t3 : more tha n 30us the period of canceling com latch circuit for initialization by using disp signal. tcom pola rity initia liza tion t4: more tha n 30us the period of initialization for tcom polarity by extcomin signal. [normal operation] duration of normal driving. [off sequence] initializes me mory da ta within pixel t5 : more tha n 1v the period of initialization for va, vb, and vcom t6 : more than 1v 5v shut down
spec no. lcy-12t09302a model no. LS013B4DN01 page 1 << precautions>> notice | these specification sheets are the propri etary product of sharp corporation ("sharp") and include materials protected under copyright of sharp. do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of sharp. | the application examples in these specifi cation sheets are provided to explain the re presentative applications of the device a nd are not intended to guarantee any industrial property right or other rights or license you to use them. sharp assumes no responsibility for any problems related to any industrial propert y right of a third party resulting from the use of the device. | sharp reserves the right to make changes in the specifications, characteristics, data, materials, structures and other contents described herein at any time without notice in order to improve design or reliability. contact sharp in order to obtain the lat est specification sheets before using any sharp' s device. manufacturing locations are also subject to change without notice. observe the following points when in using any device in this publication. sharp takes no responsibility for damage caused by improper use of the devices. the devices in this publication are designed for use in general electronic equipment designs, such as: ? personal computers ? office automation ? telecommunication equipment ? test and measurement equipment ? industrial control ? audio visual and multimedia equipment ? consumer electronics the appropriate design measures should be taken to en sure reliability and safety when sharp's devices are used for equipment such as: ? transportation control and safety equipmen t(i.e.,aircraft,trai ns,automobiles,etc.) ? traffic signals ? gas leakage sensor breakers ? alarm equipment ? various safety devices etc. | sharp's devices shall not be used for equipment that requires extremely high level of reliability, such as: ? military and space applications ? nuclear power control equipment ? medical equipment for life support | sharp assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions speci fied in these specification sheets. | contact and consult with a sharp sales repres entative for any questions about this device. .
spec no. lcy-12t09302a model no. LS013B4DN01 page 11 scs,si,sclk disp: 3v amplitude extcomin : 5v amplitude. scssisclk signal scs si sclk extcomin signal extcomin disp signal disp 10% 90% tsscs trscs 10% tssi thsi 90% 90% 10% 10% 10% twsclkh twsclkl thscs tfscs trsi tfsi 10% trsclk tfsclk 10% 50% 50% twscsl twscsh 50% 10% 90% 50% 50% 50% trextcomin twextcominh tfextcomin trdisp tfdisp 10% 10% 10% 10% 90% 90% 90% 90% 90% 90% 90% 50% 50% 50% twextcominl
spec no. lcy-12t09302a model no. LS013B4DN01 page 12 6-4 power consumption (average) table6-4 ta 25 item symbol min typ max unit remark condition1 15 uw [remark6-6] condition2 30 uw [remark6-6] condition1 display mode (no display data update) common ac driving with vdd=5v, vdda=5v, fsclk=1mhz, fscs= hz, display pattern: vertical stripe display condition 2 data renew mode (with display data update: 1hz) common ac driving with vdd=5v, vdda=5v, fsclk=1mhz, fscs= hz, display pattern: vertical stripe display [remark6-6] this is the average power in normal c ondition, not the peak power for com driving. allow margin in power supply. use of capacitor is recomme nded for vdd+vdda. (if vdd and vdda are separate, use of capacitor on each is recommended.) 6-5 input signal timing chart 6-5-1 data renew mode (1 line) renews data on one specified line. (m0=?h?, m2=?l?) renews data on one specified line. (m0=?h?, m2=?l?) scs si m0 m1 m2 dmydmydmydmydmy ag0 ag1 ag2 ag3 ag4 ag5 ag6 dmy d1 d2 d3 d4 d93 d94 d95 d96 dummy data ( don't care ) scl k ? m0 mode flag: if m0 is "h". -> data refresh mode "pixel data will be updated" . if m0 is "l" -> display mode "pixel data is held. ? m1 lc polarity inversion flag: if m1is "h" then vcom="h" is output. if m1 is "l" then vcom="l" is output. in addition, if extmode is set as "h", m1 set value doesn't matter. ? m2 all flags are cleared. if m2 is "l" then all flags are cleared. when all clear are needed, refer to "all clear timing chart" ? d1 - d96 display data: if d* is "l" then black display can be appeared, if d* is "h" then white display can be appeared ? dummy data dummy data. don't care but "l" is recommended tssi thsi tsscs data writing period (96ck) data transfer period (16ck) mode selection period (3ck+5ckdmy) twsclkh twsclkl twscsh gate line address period (7ck+1ckdmy) thscs twscsl in terms of data writing period data has been stored in 1st latch block of binary driver on panel. in term of data transfer period the data which has been stored in 1st latch block is transferred to pixel memory. refer to 6-6) input signal and disp lay for gate line address setting. m1: frame inversion flag is enabled when extmode=?l?. when scs becomes l, m0 and m2 are cleared. in renew mode (when m2=?h?) do ?all clear?, and set p1 through p96 as l.
spec no. lcy-12t09302a model no. LS013B4DN01 page 13 6-5-2 data renew mode updates multiple line data. (m0=?h?, m2=?l?) scs si dummy data(don't care) sclk dummy data(don't care) dummy dat a(don't care) ? m0 mode flag: if m0 is "h" then data refresh mode "pixel data will be updated, if m0 is "l" then display mode "pixel data is held" ? m1 lc polarity inversion flag: if m1is "h" then vcom="h" is output. if m1 is "l" then vcom="l" is output. in addition, if extmode is set as "h", m1 set value doesn't matter. ? m2 all flags are cleared. if m2 is l then all flags are cleared. when all clear are needed, refer to "all clear timing chart" ? d1 - d96 display data: if d* is "l" then black display can be appeared, if d* is "h" then white display can be appeared ? dummy data dummy data. don't care but "l" is recommended dmy d95 d96 d2 d94 d1 ag0 ag1 ag2 m0 m2 dmy dmy m1 dmy dmy d2 ag1 d4 ag0 d93 d96 d94 d95 d1 d1 d2 d3 dmy ag6 ag5 ag3 dmy ag6 ag5 ag4 d95 dmy ag6 ag5 ag4 ag0 ag1 d96 tssi thsi tsscs gl1 data transfer period (96ck) gl2 mode selection period (3ck+5ckdmy) gl(n)th line data writing period (96ck) data transfer period (16ck) gl(n-1)th line thscs twsclkh twsclkl twscsl twscsh twscsh gate line address period (7ck+1ckdmy) in terms of data writing period data has been stored in 1st latch block of binary driver on panel. in term of data transfer period as an example, the 1st latch block in binary driver which stored the data of 1st gate line"gl1"output the data to gl1 and store the data for 2nd gateline"gl2" at same time. data transfer period (8ck(dymmy)+7ck(address)+1ck(dummy)=16ck) data transfer period (8ck(dummy)+7ck(address)+1ck(dummy)=16ck) refer to 6-6) input signal and disp lay for gate line address setting. input data continuously. m1: frame inversion flag is enabled when extmode=?l?. when scs becomes l, m0 and m2 are cleared. in renew mode (when m2=?h?) do ?all clear?, and set p1 through p96 as l.
spec no. lcy-12t09302a model no. LS013B4DN01 page 14 6-5-3 display mode maintains data in the memory(maitain the current display)(m0=?l? m2 ?l?) scs si dummy data(don't care) dummy data(don't care) sclk ? m0 mode flag: if m0 is "l" then display mode "pixel data is held", if m0 is "h" then data refresh mode "pixel data will be updated. ? m1 lc polarity inversion flag: if m1is "h" then vcom="h" is output. if m1 is "l" then vcom="l" is output. in addition, if extmode is set as "h", m1 set value doesn't matter. ? m2 all flags are cleared. if m2 is l then all flags are cleared. when all clear are needed, refer to "all clear timing chart" ? dummy data dummy data. don't care but "l" is recommended m0 m1 m2 m0 m1 m2 tssi thsi tsscs mode selection period (3ck) twscsh tv thscs twscsl data transfer period (more than 13ck) m1: frame inversion flag is enabled when extmode=?l?. when scs becomes l, m0 and m2 are cleared.
spec no. lcy-12t09302a model no. LS013B4DN01 page 15 6-5-4 all clear mode clear data in the pixel and the memory data and displays white color. (m0=?l? m2 ?h?) scs si dummy data(don't care) dummy data(don't care) sclk ? m0 mode flag: if m0 is "l" then display mode "pixel data is held", if m0 is "h" then data refresh mode "pixel data will be updated. ? m1 lc polarity inversion flag: if m1is "h" then vcom="h" is output. if m1 is "l" then vcom="l" is output. in addition, if extmode is set as "h", m1 set value doesn't matter. ? m2 all flags are cleared. if m2 is l then all flags are cleared. when all clear are needed, refer to "all clear timing chart" ? dummy data dummy data. don't care but "l" is recommended m0 m1 m2 m0 m1 m2 tssi thsi tsscs mode selection period (3ck) twscsh tv thscs twscsl data transfer period (more than 13ck) m1: frame inversion flag is enabled when extmode=?l?. when scs becomes l, m0 and m2 are cleared.
spec no. lcy-12t09302a model no. LS013B4DN01 page 16 6-5-5 com inversion there are two signals, one is com signa l with serial inpu t(extmode=?l?) and other is external com si gnal input (extmode=?h?). scs si com ? m1 lc polarity inversion flag: if m1is "h" then vcom="h" is output. if m1 is "l" then vcom="l" is output. 1 lc inversion has been changed by m1 flag statement. 2 the periods of plus polarity and minus polarity should be same length as much as possible. scs extcomin comz com 1 lc inversion polarity has been set by the rising timing of extcomin in internal circuit block as comz signal, and when scs become falling timing, lc inversion has been activated as com signal. 2 the period of extcomin should be constant. extmode="l" extmode="h" qn-1 com has been changed polarity when scs meet falling edge. com hh qn-1 qn-1 ll h comz hh ?? ? ll l h hl l h h extcomin l ?? ? com extcomin m2 m1 m2 m0 m1 comz scs="l" scs="h " m0 m1 m2 h m0 l ?? l ? fcom 2 2 1 1 1 extmode="l" fcom 2 2 1 extmode="h" truth table of com 1 1 fextcomin depend on status of m1 twextcomin in rising timing of extmode, internal signal "comz" is inverted. (comz status has been fixed by signal scs)
spec no. lcy-12t09302a model no. LS013B4DN01 page 17 6-6 input signal and display, gate address(line) setting data position in display h,v ag0ag1ag2ag3ag4ag5ag6 l1hllllll l2lhlllll l3hhlllll ???????? ???????? ???????? l94lhhhhlh l95hhhhhlh l96lllllhh `?????O gate line address setting line p1,l1 p1,l2 p1,l3 p1,l96 p2,l1 p96,l96 p96, l1 p2,l2 p3,l1 up display side up
spec no. lcy-12t09302a model no. LS013B4DN01 page 18 7 optical characteristics table 7-1 ta=25 item symbol min. typ. max. unit remark h 21, 22 tbd (degree) 11 tbd (degree) viewing angle cr R 5 v 12 tbd (degree) [remark7-1] contrast ratio cr. 5 10 [remark7-2 ? 3] reflecivity ratio r 50 % [remark7-3] rise r 50 ms response time fall d 50 ms [remark 7-3,4] x 0.313 [remark7-3] panel chromaticity white y 0.338 [ [remark7-3] optical characteristics measurement equipment. figure 7-2 is for contrast ratio, reflectivity ratio, and panel chromaticity measurement, and figure 7-3 is for response time measurement. both are to be conducted in a dark or room equipment to a dark room fig7-2 contrast ratio, reflection ratio, panel chromaticity of white fig7-3 response time display center lcd panel normal line light receiver light source -30 display center measurement equipment (lcd-5200) measurement equipment (cm-2002) no rmal lin e light receiver light source lcd panel integrating sphere
spec no. lcy-12t09302a model no. LS013B4DN01 page 19 [remark7-1] defintion of viewint angle [remark7-2] defintion of contrast retio contrast ratio(cr) [remark7-4] respons time (change in reflection ratio) it?s difined by the time change of optical receiver output when signal is input to display white or black reflection intensity in white display reflection intensity in black display photo detector output 100% 90% time 10% 0% white black white 6 o?clock normal ? 21 ? 22 ? 12 ? 11
spec no. lcy-12t09302a model no. LS013B4DN01 page 20 8 module outline 1.35 inch 9696 monochromatic zebra connector specifications external form drawing fig8-1 fig 8-2
spec no. lcy-12t09302a model no. LS013B4DN01 page 21 9. external capacitor fig.9-1 external capacitor recommendation capacity value recommended capacity value c1 disp- vss: rank b 0.1uf ceramic capacitor c2 vdda- vss: rank b 1uf ceramic capacitor c3 vdd- vss: rank b 1uf ceramic capacitor [remark] the recommedation capacity of an external capacitor is shown. finally, determine a capacity value after performing evaluation sufficient by your system. (more bigger capacity value is selectable.)
spec no. lcy-12t09302a model no. LS013B4DN01 page 22 10. external power supply circuit 10-1an external power supply circuit is necessary to drive the pixel memory lcd with the 3v battery. table 1-1 shows power supply ic of the recommendation. table 1-1 maker model number note sii s-8821 charge pump type national semiconductor lm2750 charge pump type refer to specifications of each power supply ic for a detailed specification. set the constant value after it evaluating it sufficiently by an actual application when you use it. 10-2. electrical specification table 2-1 vin [v] vout model number min max min typ max iout [a] s-8821 2.8 5.0 4.9 5.0 5.1 0.04 lm2750 2.7 5.6 4.8 5.0 5.2 0.04 refer to specifications of each power supply ic for a detailed specification. set the constant value after it evaluating it sufficiently by an actual application when you use it. 10-3. reference circuit the reference circuit is shown below. s-8821 lm2750
spec no. lcy-12t09302a model no. LS013B4DN01 page 23 11 zebra connector contact resistance lower than 20 ? recommended zebra connector ? please select one from these two types. shin-etsu polymer: ms-g type recommended size l 27.70.25mm w 1.80.1mm h 2.30.1mm p 0.1mm shin-etsu polymer: gb-u type recommended size l 27.30.6mm w 1.70.2mm h 2.30.2mm p 0.1mm the zebra connector placement position 1 ms-g specifications a figure of reference 2 gb-u specifications a figure of reference fig 11-1 fig11-2
spec no. lcy-12t09302a model no. LS013B4DN01 page 24 12. packaging 12-1 serial number .( ink-jet print) show an indication point in a figure of external form dimensions of fig 12-1. print structure abc d serial number specifications a a single figure of the year b month(1,2....9,x,y,z) c day d serial numbe fig 12-1 serial number print position model number display side up back side up LS013B4DN01 9312ad00001fa
spec no. lcy-12t09302a model no. LS013B4DN01 page 25 12-2 forwarding form piling number of cartons : max 12 package quality in a carton: 1,000pcs conditions for storage. ? temperature 0 40 ? humidity 60%rh or less (at 40 ) no dew condensation at low temperature and high humidity. ? atmosphere harmful gas, such as acid or alkali which bites electronic components and/or wires, must not be detected. ? period : about 3 months ? opening of the package : in order to prevent the lcd module from breakdown by electrostatic charge, please control the room humidity over 50%rh and open the package taking sufficient countermeasures against electro static charges, such as earth, etc. 12-3 packaging fig 12-2 packege form
spec no. lcy-12t09302a model no. LS013B4DN01 page 26 13. reliability test conditions 13-1 reliability test items table13-1 test item test condition remark 1 high temperature storage test ta=80 240h 2 low temperature storage test ta=35 240h 3 high temperature and high humidity operating test tp=40 /95%rh 240h 4 high temperature operating test tp=70 240h 5 low temperature operating test tp=-20 240h 6 shock test ta=-30 (1h) +80 (1h) / 5 cycle 7 electro static discharge test 200v 200pf(0 ? ) each terminai: 1 time [remark] ta = ambient temperat ure, tp = panel temperature [check items] in the standard condition, there sha ll be no practical problems that may affect the display function. 13-2 panel surface stress spesification panel surface stress spesification has been defined as a para meter ?force of stress [n]? without no picture failer. load testing minimum 120[n] test condition : test stracture lcd panel with uv protection film press point center of lcd panel press jig 10mm column press speed 1mm minute support fixed on stage press time 5 seconds after achievement of the press strength, then reless it.
north america sharp microelectronics of the americas 5700 nw pacific rim blvd. camas, wa 98607, u.s.a. phone: (1) 360-834-8700 fax: (1) 360-834-8903 www.sharpsma.com taiwan sharp electronic components (taiwan) corporation 8f-a, no. 16, sec. 4, nanking e. rd. taipei, taiwan, republic of china phone: (886) 2-2577-7341 fax: (886) 2-2577-7326/2-2577-7328 china sharp microelectronics of china (shanghai) co., ltd. 28 xin jin qiao road king tower 16f pudong shanghai, 201206 p.r. china phone: (86) 21-5854-7710/21-5834-6056 fax: (86) 21-5854-4340/21-5834-6057 head office: no. 360, bashen road, xin development bldg. 22 waigaoqiao free trade zone shanghai 200131 p.r. china email: smc@china.global.sharp.co.jp europe sharp microelectronics europe division of sharp electronics (europe) gmbh sonninstrasse 3 20097 hamburg, germany phone: 49 (0)180 507 35 07 fax: (49) 40-2376-2232 www.sharpsme.com singapore sharp electronics (singapore) pte., ltd. 438a, alexandra road, #05-01/02 alexandra technopark, singapore 119967 phone: (65) 271-3566 fax: (65) 271-3855 korea sharp electronic components (korea) corporation rm 501 geosung b/d, 541 dohwa-dong, mapo-ku seoul 121-701, korea phone: (82) 2-711-5813 ~ 8 fax: (82) 2-711-5819 japan sharp corporation electronic components & devices 22-22 nagaike-cho, abeno-ku osaka 545-8522, japan phone: (81) 6-6621-1221 fax: (81) 6117-725300/6117-725301 www.sharp-world.com hong kong sharp-roxy (hong kong) ltd. level 26, tower 1, kowloon commerce centre, no. 51, kwai cheong road, kwai chung, new territories, hong kong phone: (852) 28229311 fax: (852) 28660779 www.sharp.com.hk shenzhen representative office: room 602-603, 6/f., international chamber of commerce tower, 168 fuhua rd. 3, cbd, futian district, shenzhen 518048, guangdong, p.r. china phone: (86) 755-88313505 fax: (86) 755-88313515 specifications are subject to change without notice. suggested applications (if any) are for standard use; see important restrictions for limitations on special applications. see limited warranty for sharps product warranty. the limited warranty is in lieu, and exclusive of, all other warranties, express or implied. all express and implied warranties, including the warranties of merchantability, fitness for use and fitness for a particular purpose, are specifically excluded. in no event will sharp be liable, or responsible in any way , for any incidental or consequential economic or property damage. lcd group lcd specification technical document

▲Up To Search▲

Price & Availability of LS013B4DN01

	To Download LS013B4DN01 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .