![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
1. general description the isp1507 is a universal serial bus (usb) high-speed host and peripheral transceiver that is fully compliant with universal serial bus specification rev. 2.0 and utmi+ low pin interface (ulpi) specification rev. 1.1 . the isp1507 can transmit and receive usb data at high-speed (480 mbit/s), full-speed (12 mbit/s) and low-speed (1.5 mbit/s), and provides a pin-optimi zed, physical layer front-end attachment to usb ho st, peripheral and otg devices. it is ideal for use in portable electronic devices, such as mobile phones, digital still cameras, digital video cameras, personal digital assistants (pdas) and digital audio players. it allows usb application-specific integrated circuits (asics), programmable logic devices (plds) and any system chip set to interface with the physical layer of the usb through a 12-pin interface. the isp1507 can interface to the link with digi tal i/o voltages in the range of 1.65 v to 3.6 v. the isp1507 is available in hvqfn24 package. 2. features ? fully complies with: ? universal serial bus specification rev. 2.0 ? utmi+ low pin interface (ulp i) specification rev. 1.1 ? interfaces to host and peripheral cores; optimized for stand-alone and embedded host applications with an external v bus supply; stand-alone peripheral cores, and session request protocol (srp)-capable peripheral cores ? complete hi-speed usb physical front-end solution that supports high-speed (480 mbit/s), full-speed (12 mbit/s) and low-speed (1.5 mbit/s) ? integrated 45 ? 10 % high-speed terminat ion resistors, 1.5 k ? 5 % full-speed device pull-up resistor, and 15 k ? 5 % host termination resistors ? integrated parallel-to-serial and serial-to- parallel converters to transmit and receive ? usb clock and data recovery to receive usb data up to 500 ppm ? insertion of stuff bits during transmit an d discarding of stuff bits during receive ? non-return-to-zero inverted (nrzi) encoding and decoding ? supports bus reset, suspend, resume and high-speed detection handshake (chirp) ? supports srp for reduced power consumption ? complete control over bus resistors ? data line and v bus pulsing session request methods ? integrated v bus voltage comparators isp1507c; isp1507d ulpi hi-speed usb host and peripheral transceiver rev. 04 ? 20 may 2010 product data sheet
cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 2 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver ? highly optimized ulpi compliant ? 60 mhz, 12-bit interface between the core and the transceiver ? supports 60 mhz output clock configuration ? integrated phase-locked loop (pll) supporting one crystal or clock frequency: 19.2 mhz (isp1507cbs) and 26 mhz (isp1507dbs) ? fully programmable ulpi-compliant register set ? internal power-on reset (por) circuit ? flexible system integration and very low cu rrent consumption, optimized for portable devices ? power-supply input range is 3.0 v to 3.6 v ? internal voltage regulator supplies 3.3 v and 1.8 v ? supports external v bus charge pump ? external v bus source is controlled using t he psw_n pin; open-drain psw_n allows per-port or ganged power control ? fault input pin to monitor the external v bus supply status ? supports wide range interfacing i/o voltage of 1.65 v to 3.6 v; separate i/o voltage pins minimize crosstalk ? typical operating current of 11 ma to 48 ma, depending on the usb speed and bus utilization ? typical suspend current of 30 a ? full industrial grade operating temperature range from ? 40 c to +85 c ? 4 kv electrostatic discharge (esd) protection on pins dp, dm, v bus and gnd ? available in a small hvqfn24 (4 mm 4 mm) restriction of hazardous substances (rohs) compliant, halogen-free and lead-free package 3. applications ? digital still camera ? digital tv ? digital video disc (dvd) recorder ? external storage device, for example: ? magneto-optical (mo) drive ? optical drive: cd-rom, cd-rw, dvd ? zip drive ? mobile phone ? mp3 player ? pda ? printer ? scanner ? set-top box (stb) ? video camera cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 3 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 4. ordering information [1] the package marking is the first line of text on the ic package and can be used for ic identification. table 1. ordering information commercial product code marking crystal or clock frequency package description packing minimum sellable quantity isp1507cbsum 507c [1] 19.2 mhz hvqfn24; 24 terminals; body 4 4 0.85 mm 13 inch tape and reel dry pack 6000 pieces ISP1507DBSUM 507d [1] 26 mhz hvqfn24; 24 terminals; body 4 4 0.85 mm 13 inch tape and reel dry pack 6000 pieces cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 4 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 5. block diagram fig 1. block diagram register map ulpi interface controller usb data serializer usb data deserializer high-speed usb atx dm dp stp dir nxt data [7:0] 8 5 6 16 15 14 1, 2, 17 to 20, 22, 24 004aab078 clock 21 termination resistors v bus comparators srp charge and discharge resistors power-on reset pll crystal oscillator voltage regulator band gap reference voltage rref 4 internal power v cc 7 reg3v3 reg1v8 9 13 reset_n/ psw_n global reset global clocks xtal2 xtal1 10 11 v cc(i/o) 3, 23 interface voltage v bus / fault 8 isp1507 12 ulpi interface usb cable v ref v bus valid external drive v bus external cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 5 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 6. pinning information 6.1 pinning 6.2 pin description fig 2. pin configuration hvqfn24; top view 004aab079 isp1507 transparent top view reg1v8 dm dp dir rref stp v cc(i/o) nxt data0 data7 data1 data6 v cc v bus /fault reg3v3 xtal1 xtal2 reset_n/ psw_n data2 v cc(i/o) data3 clock data4 data5 terminal 1 index area 6 13 5 14 4 15 3 16 2 17 1 18 7 8 9 10 11 12 24 23 22 21 20 19 table 2. pin description symbol [1] [2] pin type [3] description [4] data1 1 i/o pin 1 of the bidirectional ulpi data bus slew-rate controlled output (1 ns); plain input; programmable pull down data0 2 i/o pin 0 of the bidirectional ulpi data bus slew-rate controlled output (1 ns); plain input; programmable pull down v cc(i/o) 3 p i/o supply rail rref 4 ai/o resistor reference dm 5 ai/o data minus (d ? ) pin of the usb cable dp 6 ai/o data plus (d+) pin of the usb cable v cc 7 p input supply voltage or battery source v bus /fault 8 ai/o this pin has two possible functions: v bus (analog input and output) ? v bus pin of the usb cable. fault (input) ? input pin for the external v bus digital overcurrent or fault detector signal. if this pin is not used as either v bus or fault, it must be connected to ground. 5 v tolerant reg3v3 9 p 3.3 v regulator output; requires parallel 0.1 f and 4.7 f capacitors; internally powers atx and other analog circuits; must not be used to power external circuits xtal1 10 ai crystal oscillator or clock input xtal2 11 ao crystal oscillator output cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 6 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver [1] symbol names ending with underscore n, for ex ample, name_n, indicate active low signals. [2] for details on external components required on each pin, see list of materials and application diagrams in section 16 . [3] i = input; o = output; i/o = digital input/output; ai = analog input; ao = analog output; ai/o = analog input/output; p = power or ground pin. [4] a detailed description of these pins can be found in section 7.10 . reset_n/psw_n 12 i/o this pin has two possible functions: reset_n (input) ? active low, asynchronous reset input. 3.3 v tolerant; plain input psw_n (output) ? active low external v bus power switch or external charge pump enable. open-drain; 3.3 v tolerant if not used, this pin must be connected to v cc(i/o) . reg1v8 13 p 1.8 v regulator output; requires parallel 0.1 f and 4.7 f capacitors; internally powers the digital core; must not be used to power external circuits dir 14 o ulpi direction signal slew-rate controlled output (1 ns) stp 15 i ulpi stop signal plain input; programmable pull up nxt 16 o ulpi next signal slew-rate controlled output (1 ns) data7 17 i/o pin 7 of the bidirectional ulpi data bus slew-rate controlled output (1 ns); plain input; programmable pull down data6 18 i/o pin 6 of the bidirectional ulpi data bus slew-rate controlled output (1 ns); plain input; programmable pull down data5 19 i/o pin 5 of the bidirectional ulpi data bus slew-rate controlled output (1 ns); plain input; programmable pull down data4 20 i/o pin 4 of the bidirectional ulpi data bus slew-rate controlled output (1 ns); plain input; programmable pull down clock 21 o 60 mhz clock output slew-rate controlled output (1 ns) data3 22 i/o pin 3 of the bidirectional ulpi data bus slew-rate controlled output (1 ns); plain input; programmable pull down v cc(i/o) 23 p i/o supply rail data2 24 i/o pin 2 of the bidirectional ulpi data bus slew-rate controlled output (1 ns); plain input; programmable pull down gnd die pad p ground supply; down bonded to the exposed die pad (heat sink); to be connected to the pcb ground table 2. pin description ?continued symbol [1] [2] pin type [3] description [4] cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 7 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 7. functional description 7.1 ulpi controller the isp1507 provides a 12-pin interface that is compliant with utmi+ low pin interface (ulpi) specification rev. 1.1 . this interface must be connected to the usb link. the ulpi controller provides the following functions: ? ulpi compliant and register set ? allows full control over the usb pe ripheral, host and srp functionality ? parses the usb transmit and receive data ? prioritizes the usb receive data, usb transmit data, interrupts and register operations ? low-power mode ? external v bus source control ? v bus monitoring, charging and discharging ? 6-pin serial mode and 3-pin serial mode ? generates rxcmds; status updates ? maskable interrupts for more information on the ulpi protocol, see section 9 . 7.2 usb serializer and deserializer the usb data serializer prepares data to transmit on the usb bus. to transmit data, the usb link sends a transmit command and data on the ulpi bus. the serializer performs parallel-to-serial conversion, bit stuffing an d nrzi encoding. for packets with a pid, the serializer adds a sync pattern to the start of the packet, and an eop pattern to the end of the packet. when the serializer is busy and cannot accept any more data, the ulpi controller deasserts nxt. the usb data deserializer decodes data received from the usb bus. when data is received, the deserializer strips the sy nc and eop patterns, and then performs serial-to-parallel conversion, nrzi decoding and discarding of stuff bits on the data payload. the ulpi controller sends data to the usb link by asse rting dir, and then asserting nxt whenever a byte is ready. the deserializer also de tects various receive errors, including bit stuff errors, elasticity buffer underrun or overrun, and byte-alignment errors. 7.3 hi-speed usb (usb 2.0) atx the hi-speed usb atx block is an analog front-end containing the circuitry needed to transmit, receive and terminate the usb bus in high-speed, full-speed and low-speed, for usb peripheral, host and otg implementations. the following circuitry is included: ? differential drivers to transmit data at high-speed, full-speed and low-speed ? differential and single-ended receivers to receive data at high-speed, full-speed and low-speed ? squelch circuit to detect high-speed bus activity cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 8 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver ? high-speed disconnect detector ? 45 high-speed bus terminations on dp and dm for peripheral and host modes ? 1.5 k pull-up resistor on dp for full-speed peripheral mode ? 15 k bus terminations on dp and dm for host and otg modes for details on controlling resistor settings, see ta b l e 7 . 7.4 voltage regulator the isp1507 contains a built-in voltage regulator that conditions the v cc supply for use inside the isp1507. the voltage regulator: ? supports input supply range of 3.0 v < v cc <3.6v ? supplies internal circuitry with 1.8 v and 3.3 v remark: the reg1v8 and reg3v3 pins require external decoupling capacitors. for details, see section 16 . 7.5 crystal oscillator and pll the isp1507 has a built-in crystal oscillato r and a phase-locked loop (pll) for clock generation. the crystal oscillator takes a sine-wave input fr om an external crystal on the xtal1 pin, and converts it to a square wave clock for inte rnal use. alternatively, a square wave clock of the same frequency can also be directly dr iven into the xtal1 pin. using an existing square wave clock can save the cost of the crystal and also reduce the board size. the pll takes the square wave cl ock from the crystal oscillator, and multiplies or divides it into various frequencies for internal use. the pll produces the following frequencies, irrespective of the clock source: ? 60 mhz clock for the ulpi controller ? 1.5 mhz for the low-speed usb data ? 12 mhz for the full-speed usb data ? 480 mhz for the high-speed usb data ? other internal frequencies for data conversion and data recovery 7.6 v bus comparators the isp1507 provides three comparators, v bus valid comparator, session valid comparator and session end comparator, to detect the v bus voltage level. 7.6.1 v bus valid comparator this comparator is used by hosts and a- devices to determine whether the voltage on v bus is at a valid level for operation. the isp1507 minimum threshold for the v bus valid comparator is 4.4 v. any voltage on v bus below this threshold is considered invalid. during power-up, it is ex pected that the comparat or output will be ignored. cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 9 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver while it is possible for the external 5 v supply to use the isp1507 internal a_vbus_vld comparator, typical 5 v supplies must provide their own power fault indicator that can be connected as an input to the isp1507 fault pin. 7.6.2 session valid comparator the session valid comparator is a ttl-level input that determines when v bus is high enough for a session to start. peripherals, a-devices and b-devices use this comparator to detect when a session is started. the a-device also uses this comparator to determine when a session is completed. the session valid threshold of the isp1507 is v b_sess_vld , with a hysteresis of v hys(b_sess_vld) . 7.6.3 session end comparator the isp1507 session end comparator determines when v bus is below the b-device session end threshold. the b-device uses this threshold to determine when a session has ended. the session end threshold of the isp1507 is v b_sess_end . 7.7 srp charge and discharge resistors the isp1507 provides on-chip resistors for short-term charging and discharging of v bus . these are used by the b-device to request a session, prompting the a-device to restore the v bus power. first, the b-de vice makes sure that v bus is fully discharged from the previous session by setting the dischrg_vbus register bit to logi c 1 and waiting for sess_end to be logic 1. then the b-device charges v bus by setting the chrg_vbus register bit to logic 1. the a-device sees that v bus is charged above the session valid threshold and starts a session by turning on the v bus power. 7.8 band gap reference voltage the band gap circuit provides a stable intern al voltage reference to bias the analog circuitry. the band gap requires an accu rate external reference resistor, r rref , connected between the rref and gnd pins. for details, see section 16 . 7.9 power-on reset the isp1507 has an internal power-on reset circuit that resets all internal logic on power-up. the ulpi is also reset at power-up. remark: when clock starts toggling after power-up, the usb link must issue a reset command over the ulpi bus to ensure correct operation of the isp1507. 7.10 detailed description of pins 7.10.1 data[7:0] the isp1507 is a physical layer (phy) containing a usb transceiver. data[7:0] is a bidirectional data bus. the usb link must dr ive data[7:0] to low when the ulpi bus is idle. when the link has data to transmit to the phy, it drives a nonzero value. weak pull-down resistors are incorporated into data[7:0] pins as part of the interface protect feature. for details, see section 9.3.1 . the data bus can be reconfigured to carry various data types, as given in section 8 and section 9 . cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 10 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 7.10.2 v cc(i/o) the input power pin that sets the i/o voltage level. for details, see section 12 , section 13 and section 16 . v cc(i/o) provides power to on-chip pads of the following pins: ? clock ? data[7:0] ? dir ? nxt ? reset_n ? stp 7.10.3 rref resistor reference analog i/o pin. a resistor, r rref , must be connected between rref and gnd, as shown in section 16 . this provides an accurate voltage reference that biases internal analog circuitry. less accurate resistors cann ot be used and will render the isp1507 unusable. 7.10.4 dp and dm the dp (data plus) and dm (data minus) are usb differential data pins. these must be connected to the d+ and d ? pins of the usb receptacle. 7.10.5 v cc v cc is the main input supply voltage for the isp1507. decoupling capacitors are recommended. for details, see section 16 . 7.10.6 v bus /fault this pin provides two options for v bus driving and monitoring. if neither function is used, this pin must be connected to ground. 7.10.6.1 v bus by default, this pin acts as an input to v bus comparators, and also charges and discharges v bus for srp. the v bus pin requires a capacitive load as shown in section 16 . to prevent electrical overstress, it is st rongly recommended that you attach a series resistor on the v bus pin (r vbus ), see section 16 . 7.10.6.2 fault (external overcurrent or fault detector) if an external v bus overcurrent or fault circuit is used, the output fault indicator of that circuit can be connected to th e isp1507 fault input pin. the isp1507 will inform the link of v bus fault events by sending rxcmds on the ul pi bus. to use the fault pin, the link must: ? set the use_ext_vbus_ind register bit to logic 1. ? set the polarity of the external fault signal using the ind_compl register bit. ? set the ind_passthru register bit to logic 1. cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 11 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 7.10.7 reg3v3 and reg1v8 regulator output voltage. these supplies are used to power the isp1507 internal digital and analog circuits, and must not be used to power external circuits. for correct operation of the regulator, it is recommended that you connect reg3v3 and reg1v8 to decoupling capacitors. for an example, see section 16 . 7.10.8 xtal1 and xtal2 xtal1 is the crystal input, and xtal2 is the crystal output. the allowed frequency on the xtal1 pin depends on the isp1507 product version. if the link requires a 60 mhz clock from the isp1507, then either a crystal must be attached, or a clock of the same frequency must be driven into xtal1, with xtal2 left floating. if a crystal is attached, it requires external load capacitors to gnd on each terminal of the crystal. for details, see section 16 . if at any time the system wants to stop the clock on xtal1, the lin k must first put the isp1507 into low-power mode. the clock on xtal1 must be restarted before low-power mode is exited. 7.10.9 reset_n/psw_n this pin provides two optional functions. if neither function is used, this pin must be connected to v cc(i/o) . 7.10.9.1 reset_n an active low asynchronous reset pin that resets all circuits in the isp1507. the isp1507 contains an internal power-on rese t circuit, and theref ore using the reset_n pin is optional. if reset_n is not used, it must be connected to v cc(i/o) . for details on us ing reset_n, see section 9.3.2 . 7.10.9.2 psw_n psw_n is an active low, open-drain output pin. this pin can be connected to an active low, external v bus switch or charge pump enable circuit to control the external v bus power source. an external pull-up resistor, r pullup , is required when psw_n is used. this pin is open-drain, allowing ganged-mode power control for multiple usb ports. for application details, see section 16 . to use the psw_n pin, the link must disable the reset input by setting the ignore_reset bit in the pw r_ctrl register (see section 10.1.14 ) to logic 1. this will ensure that psw_n is not misinterpreted as a reset. if the link is in host mode, it can enable the external v bus power source by setting the drv_vbus_ext bit in the otg_ctrl register (see section 10.1.4 ) to logic 1. the isp1507 will drive psw_n to low to enable the external v bus power source. if the link detects an overcurrent condition (the v bus state in rxcmd is not 11b), it must disable the external v bus supply by setting drv_vbus_ext to logic 0. cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 12 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 7.10.10 dir ulpi direction output pin. controls the direct ion of the data bus. by default, the isp1507 holds dir at low, causing the data bus to be an input. when dir is low, the isp1507 listens for data from the link. the isp1507 pu lls dir to high only when it has data to send to the link, which is for one of two reasons: ? to send the usb receive data, rxcmd status updates and register reads data to the link. ? to block the link from driving the data bus during power-up, reset and low-power mode (suspend). for details on dir usage, refer to utmi+ low pin interface (ulpi) specification rev. 1.1 . 7.10.11 stp ulpi stop input pin. the link must assert stp to signal the end of a usb transmit packet or a register write operation. when dir is asserted, the link can opt ionally assert stp to abort the isp1507, causing it to deassert di r in the next clock cycle. a weak pull-up resistor is incorporated into the stp pin as pa rt of the interface prot ect feature. for details, see section 9.3.1 . for details on stp usage, refer to utmi+ low pin interface (ulpi) specification rev. 1.1 . 7.10.12 nxt ulpi next data output pin. the isp1507 hold s nxt at low, by default. when dir is low and the link is sending data to the isp1507, nxt will be asse rted to notify the link to provide the next data byte. when dir is at hi gh and the isp1507 is sending data to the link, nxt will be asserted to notify the link that another valid byte is on the bus. nxt is not used for register read data or the rxcmd status update. for details on nxt usage, refer to utmi+ low pin interface (ulp i) specification rev. 1.1 . 7.10.13 clock a 60 mhz interface clock to synchronize the ulpi bus. the isp1507 provides two clocking options: ? a crystal is attached between the xtal1 and xtal2 pins. ? a clock is driven into the xtal1 pin, with the xtal2 pin left floating. for details on clock usage, refer to utmi+ low pin interface (ulpi) specification rev. 1.1 . 7.10.14 gnd (die pad) global ground signal. the die pad is expos ed on the underside of the package as a ground plate. this acts as a ground to all circuits in the isp1507. to ensure correct operation of the isp1507, gnd must be soldered to the cleanest ground available. cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 13 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 8. modes of operation 8.1 ulpi modes the isp1507 ulpi bus can be programmed to operate in four modes. each mode reconfigures the signals on the data bus as described in the following subsections. setting more than one mode will le ad to undefined behavior. 8.1.1 synchronous mode this is default mode . at power-up, and when clock is stable, the isp1507 will enter synchronous mode. the link must synchronize all ulpi signals to clock, meeting the set-up and hold times as defined in section 15 . a description of the ulpi pin behavior in synchronous mode is given in ta b l e 3 . this mode is used by the link to perform the following tasks: ? high-speed detection handshake (chirp) ? transmit and receive usb packets ? read and write to registers ? receive usb status updates (rxcmds) for more information on various synchronous mode protocols, see section 9 . table 3. ulpi sign al description signal name direction on isp1507 signal description clock o 60 mhz interface clock . if a crystal is attached or a clock is driven into the xtal1 pin, the isp1507 will drive a 60 mhz output clock. data[7:0] i/o 8-bit data bus . in synchronous mode, the link drives data[7:0] to low by default. the link initiates transf ers by sending a nonzero data pattern called txcmd (transmit command). in synchronous mode, the direction of data[7:0] is controlled by dir. contents of data[7:0] lines must be ignored for exactly one clock cycle whenever dir changes value. this is called the turnaround cycle. data lines have fixed direction and different meaning in low-power and serial modes. cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 14 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 8.1.2 low-power mode when the usb is idle, the link can place the isp1507 into low-power mode (also called suspend mode). in low-power mode, the data bus definition changes to that shown in ta b l e 4 . to enter low-power mode, the link sets the suspendm bit in the func_ctrl register (see section 10.1.2 ) to logic 0. to exit low-power mode, the link asserts the stp signal. the isp1507 will draw only suspend current from the v cc supply (see ta b l e 4 4 ). during low-power mode, the clock on xtal1 may be stopped. the clock must be started again before asserting stp to exit low-po wer mode. after exitin g low-power mode, the isp1507 will send an rxcmd to the link if a change was detected in any interrup t source, and the change still exists. an rxcmd may no t be sent if the interrupt condition is removed before exiting. for more information on low-power mode enter and exit protocols, refer to utmi+ low pin interface (ulpi) specification rev. 1.1 . dir o direction : controls the direction of data bus data[7:0]. in synchronous mode, the isp1507 drives dir to lo w by default, making the data bus an input so that the isp1507 can li sten for txcmds from the link. the isp1507 drives dir to high only when it has data for the link. when dir and nxt are high, the byte on the data bus contains decoded usb data. when dir is high and nxt is low, the byte contains status information called rxcmd (receive command). the only exception to this rule is when the phy returns register read data, where nxt is also low, replacing the usual rxcmd byte. every change in dir causes a turnaround cycle on the data bus, during which data[7:0] is not valid and must be ignored by the link. dir is always asserted during low-power and serial modes. stp i stop : in synchronous mode, the link drives stp to high for one cycle after the last byte of data is sent to the isp1507. the link can optionally assert stp to force dir to be deasserted. in low-power and serial modes, the link holds stp at high to wake up the isp1507, causing the ulpi bus to return to synchronous mode. nxt o next : in synchronous mode, the isp1507 drives nxt to high to throttle data. if dir is low, the isp1507 asserts nxt to notify the link to place the next data byte on data[7:0] in th e following clock cycle. if dir is high, the isp1507 asserts nxt to notify the link that a valid usb data byte is on data[7:0] in the current cycle. the isp1507 always drives an rxcmd when dir is high and nxt is low, unless register read data is to be returned to t he link in the current cycle. nxt is not used in low-power or serial mode. table 3. ulpi sign al description ?continued signal name direction on isp1507 signal description table 4. signal mapping during low-power mode signal maps to direction description linestate0 data0 o combinatorial linestate0 directly driven by the analog receiver linestate1 data1 o combinatorial linestate1 directly driven by the analog receiver cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 15 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 8.1.3 6-pin full-speed or low-speed serial mode if the link requires a 6-pin serial interface to transmit and receive full-speed or low-speed usb data, it can set the isp1507 to 6-pin serial mode. in 6-pin serial mode, the data[7:0] bus definition changes to that shown in ta b l e 5 . to enter 6-pin serial mode, the link sets the 6pin_fsls_serial bit in the intf_ctrl register (see section 10.1.3 ) to logic 1. to exit 6-pin serial mode, the link asserts stp. th is is provided primarily for links that contain legacy full-speed or low-speed functionality, providing a more cost-effective upgrade path to high-speed. an interrupt pin is also provided to inform the link of usb events. if the link requires clock to be runn ing during 6-pin serial mode, the cl ock_suspendm register bit must be set to logic 1. for more information on 6-pin serial mode enter and exit protocols, refer to utmi+ low pin interface (ulpi) specification rev. 1.1 . 8.1.4 3-pin full-speed or low-speed serial mode if the link requires a 3-pin serial interface to transmit and receive full-speed or low-speed usb data, it can set the isp1507 to 3-pin seri al mode. in 3-pin serial mode, the data bus definition changes to that shown in ta b l e 6 . to enter 3-pin serial mode, the link sets the 3pin_fsls_serial bit in the intf_ctrl register (see section 10.1.3 ) to logic 1. to exit 3-pin serial mode, the link asserts stp. this is primarily provided for links that contain legacy full-speed or low-speed functionality, providing a more cost-effective upgrade path to high-speed. an interrupt pin is also provided to inform the link of usb events. if the link requires clock to be runn ing during 3-pin serial mode, the cl ock_suspendm register bit must be set to logic 1. for more information on 3-pin serial mode enter and exit protocols, refer to utmi+ low pin interface (ulpi) specification rev. 1.1 . reserved data2 o reserved; the isp1507 will drive this pin to low int data3 o active high interrupt indication; will be asserted whenever any unmasked interrupt occurs reserved data[7:4] o reserved; the isp1507 will drive these pins to low table 4. signal mapping during low-power mode ?continued signal maps to direction description table 5. signal mapping for 6-pin serial mode signal maps to direction description tx_enable data0 i active high transmit enable tx_dat data1 i transmit differential data on dp and dm tx_se0 data2 i transmit single-ended zero on dp and dm int data3 o active high interrupt indication; will be asserted whenever any unmasked interrupt occurs rx_dp data4 o single-ended receive data from dp rx_dm data5 o single-ended receive data from dm rx_rcv data6 o differential receive data from dp and dm reserved data7 o reserved; the isp1507 will drive this pin to low cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 16 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 8.2 usb and otg state transitions a hi-speed usb peripheral, host or otg device handles more than one electrical state as defined in universal serial bus specification rev. 2.0 and on-the-go supplement to the usb 2.0 specification rev. 1.3 . the isp1507 accommodates the various states through register bit settings of xcvrselec t[1:0], termselect, opmode[1:0], dp_pulldown and dm_pulldown. ta b l e 7 summarizes operating states. the values of register settings in table 7 will force resistor settings as also given in ta b l e 7 . resistor setting signals are defined as follows: ? rpu_dp_en enables the 1.5 k pull-up resistor on dp ? rpd_dp_en enables the 15 k pull-down resistor on dp ? rpd_dm_en enables the 15 k pull-down resistor on dm ? hsterm_en enables the 45 termination resistors on dp and dm it is up to the link to set the desired register settings. table 6. signal mapping for 3-pin serial mode signal maps to direction description tx_enable data0 i active high transmit enable dat data1 i/o transmit differential data on dp and dm when tx_enable is high receive differential data from dp and dm when tx_enable is low se0 data2 i/o transmit single-ended zero on dp and dm when tx_enable is high receive single-ended zero from dp and dm when tx_enable is low int data3 o active high interrupt indication; will be asserted whenever any unmasked interrupt occurs reserved data[7:4] o reserved; the isp1507 will drive these pins to low table 7. operating states and their corresponding resistor settings signaling mode register settings internal resistor settings xcvr select [1:0] term select opmode [1:0] dp_pull down dm_pull down rpu_ dp_en rpd_ dp_en rpd_ dm_en hsterm _en general settings 3-state drivers xxb xb 01b xb xb 0b 0b 0b 0b power-up or v bus cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 18 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 9. protocol description the following subsections describe t he protocol for using the isp1507. 9.1 ulpi references the isp1507 provides a 12-pin ulpi to communicate with the link. it is highly recommended that you read utmi+ low pin interface (ulpi) specification rev. 1.1 and utmi+ specification rev. 1.0 . 9.2 power-on reset (por) an internal por is generated when reg1v8 rises above v por(trip) , for at least t w(reg1v8_h) . the internal por pulse will also be generated whenever reg1v8 drops below v por(trip) for more than t w(reg1v8_l) , and then rises above v por(trip) again. the voltage on reg1v8 is generated from v cc . to give a better view of the functionality, figure 3 shows a possible curve of reg1v8. the internal por starts with logic 0 at t0. at t1 , the detector will see the passing of the trip level so that por turns to logic 1 and a delay el ement will add another t porp before it drops to logic 0. if reg1v8 dips from t2 to t3 for > t w(reg1v8_l) , another por pulse is generated. if the dip at t4 to t5 is too short, that is, < t w(reg1v8_l) , the internal por pulse will not react and will remain low. 9.3 power-up, reset and bus idle sequence figure 4 shows a typical start-up sequence. on power-up, the isp1507 performs an internal power-on reset and asserts dir to indicate to the link that the ulpi bus cannot be used. when the internal pll is stable, the isp1507 deasserts dir. the powe r-up time depends on the v cc supply rise time, the crystal start-up time, and pll start-up time t startup(o)(clock) . whenever dir is asserted, the isp1507 drives the nxt pin to low and dr ives data[7:0] with rxcmd values. when dir is deasserted, the link must drive the data bus to a valid level. by default, the link must drive data to low. when the isp1507 in itially deasserts dir on power-up, the link must ignore all rxcmds until it resets the isp1507. before beginning usb packets, the link must set the reset bit in the func_ctrl register (see section 10.1.2 ) to reset the isp1507. after the reset bit is set, the isp1507 will assert dir until the internal reset completes. the isp1507 will au tomatically deassert dir and clear the reset bit when reset has complete d. after every reset, an rxcmd is sent to the link to update usb status information. after this sequence, the ulpi bus is ready for use and the link can start usb operations. fig 3. internal power-on reset timing 004aaa751 reg1v8 t0 t1 t2 t3 t4 t5 v por(trip) t porp por t porp cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 19 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver if a crystal is attached or a clock is driven into the xtal1 pin, the isp1507 will drive a 60 mhz clock out from the clock pin when di r deasserts. this is shown as clock in figure 4 . the recommended power-up sequence for the link is as follows: 1. the link waits for t regup , ignoring all the ulpi pin status. 2. the link may start to detect dir status leve l. if dir is detected as low for three clock cycles, the link may send a reset command. the ulpi is ready for use. cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 20 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 9.3.1 interface protection by default, the isp1507 enables a weak pull- up resistor on stp. if the stp pin is unexpectedly high at any time, the isp1 507 will protect the ulpi by enabling weak pull-down resistor s on data[7:0]. t1 = v cc and v cc(i/o) are applied to the isp1507. the isp1507 regulator starts to turn on. t2 = ulpi pads detect reg1v8 rising above t he reg1v8 regulator threshold and are not in 3-state. these pads may drive either low or high. it is recommended that the link ignores the ulpi pins status during t regup . t3 = the por threshold is reached and a por pu lse is generated. after the por pulse, ulpi pins are driven to a defined level. dir is driven to high and the other pins are driven to low. t4 = the isp1507 regulator is powered up and is stable. t5 = the internal pll is stabilized after t startup(pll) . if the 19.2 mhz or 26 mhz clock is started before por, the internal pll will be stabilized after t startup(pll) from por. the clock pin starts to output 60 mhz. the dir pin will transition from high to low. the dir pin will remain low before the link issues a reset command to the isp1507. t6 = the power-up sequence is completed and the ulpi bus interface is ready for use. fig 4. power-up and reset sequence required before the ulpi bus is ready for use clock txcmd dir data[7:0] stp nxt 004aaa885 reset command internal clocks stable internal reset rxcmd update bus idle d v cc v cc(i/o) reg1v8 internal reg1v8 detector internal por xtal1 t startup(pll) t1 t2 t3 t4 t5 t regup t6 cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 21 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver the interface protect feature prevents unwant ed activity of the isp1507 whenever the ulpi is not correctly driven by the link. for example, when the link powers up more slowly than the isp1507. the interface protect feature can be disa bled by setting the intf_prot_dis bit to logic 1. 9.3.2 interface behavior with respect to reset_n the use of the reset_n pin is optional. when reset_n is asserted (low), the isp1507 will assert dir. all logic in the is p1507 will be reset, including the analog circuitry and ulpi registers. during reset, the link must drive data[7:0] and stp to low; otherwise undefined behavior may result. when reset_n is deasserted (high), the dir output will deassert (low) four or five clock cycles later. figure 5 shows the ulpi behavior when reset_n is as serted (low), and subsequently deasse rted (high). if reset_n is not used, it must be connected to v cc(i/o) . 9.4 v bus power and fault detection 9.4.1 driving 5 v on v bus the isp1507 supports external 5 v supplies. the isp1507 can control the external supply using the active-low psw_n open-drain output pin. to enable the external supply by driving psw_n to low, the link must se t the drv_vbus_ext bit in the otg_ctrl register (see section 10.1.4 ) to logic 1. when the drv_ vbus_ext bit is set, the drv_vbus bit can be set to any value and will be ignored. 9.4.2 fault detection the isp1507 supports external v bus fault detector circuits. an overcurrent detection circuit is required for host applications that supply more than 100 ma on v bus for voltages between 4.75 v to 5.25 v. for low-power applications supplying less than 100 ma, the v bus power line can directly be connected to the v bus /fault pin on the isp1507 and the link can utilize the internal a_vbus_vld comparator. fig 5. interface behavior with respect to reset_n clock 004aaa720 stp reset_n data[7:0] dir nxt hi-z (input) hi-z (input) hi-z (input) hi-z (input) hi-z (link must drive) hi-z (link must drive) cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 22 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver the isp1507 supports external v bus fault detector circuits that output a digital fault indicator signal. the indicator sig nal must be connected to the v bus /fault pin. to enable the isp1507 to monitor the digital fault in put, the link must se t the use_ext_vbus_ind bit in the otg_ctrl register (see section 10.1.4 ) and the ind_passthru bit in the intf_ctrl register (see section 10.1.3 ) to logic 1. for details, see figure 7 . the fault input pin is mapped to the a_vbus_vld bit in rxcmd. any changes for the fault input will trigger rxcmd carrying the fault condition with a_vbus_vld. 9.5 txcmd and rxcmd commands between the isp1507 and the link are described in the following subsections. 9.5.1 txcmd by default, the link must drive the ulpi bus to its idle state of 00h. to send commands and usb packets, the link drives a nonzero value on data[7:0] to the isp1507 by sending a byte called txcmd. commands include usb packet transmissions, and register reads and writes. once the txcmd is interpreted a nd accepted by the isp 1507, the nxt signal is asserted and the link can fo llow up with the required number of data bytes. the txcmd byte format is given in ta b l e 8 . any values other than those in ta b l e 8 are illegal and may result in undefined behavior. various txcmd packet and register se quences are shown in later sections. 9.5.2 rxcmd the isp1507 communicates status information to the link by asserting dir and sending an rxcmd byte on the data bus. the rxcmd data byte format is given in ta b l e 9 . the isp1507 will automatically s end an rxcmd whenever there is a change in any of the rxcmd data fields. the link must be able to accept an rxcmd at any time; including single rxcmds, back-to-back rxcmds, and rx cmds at any time during usb receive packets when nxt is low. an example is shown in figure 6 . for details and diagrams, refer to utmi+ low pin interface (ulp i) specification rev. 1.1 . table 8. txcmd byte format command type name command code data[7:6] command payload data[5:0] command name command description idle 00b 00 0000b noop no operation. 00h is the idle value of the data bus. the link must drive noop by default. packet transmit 01b 00 0000b nopid transmit usb data that does not have a pid, such as chirp and resume signaling. the isp1507 starts transmitting only after accepting the next data byte. 00 xxxxb pid transmit usb packet. data[3:0] indicates usb packet identifier pid[3:0]. register write 10b 10 1111b extw ext ended register write comma nd (optional). the 8-bit address must be provided after the command is accepted. xx xxxxb regw register write comman d with 6-bit immediate address. register read 11b 10 1111b extr ext ended register read command (optional). the 8-bit address must be provided after the command is accepted. xx xxxxb regr register read command with 6-bit immediate address. cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 23 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver an rxcmd may not be sent when exiting low-po wer mode or serial mode, if the interrupt condition is removed before exiting. 9.5.2.1 linestate encoding linestate[1:0] reflects the current state of dp and dm. whenever the isp1507 detects a change in dp or dm, an rxcmd will be se nt to the link with the new linestate[1:0] value. the value given on linestate[1:0] dep ends on the setting of various registers. ta b l e 1 0 shows the linestate[1:0] encoding for upstream facing ports, which applies to peripherals. ta b l e 11 shows the linestate[1:0] encodin g for downstream facing ports, which applies to host controllers. dual-rol e devices must choose the correct table, depending on whether it is in peripheral or host mode. table 9. rxcmd byte format data name description and value 1to0 linestate linestate signals : for a definition of linestate, see section 9.5.2.1 . data0 ? linestate[0] data1 ? linestate[1] 3to2 v bus state encoded v bus voltage state : for an explanation of the v bus state, see section 9.5.2.2 . 5to4 rxevent encoded usb event signals : for an explanation of rxevent, see section 9.5.2.4 . 6 reserved - 7 alt_int by default, this signal is not used and is not needed in typical designs. optionally, the link can enable the bvalid_rise and/or bvalid_fall bits in the pwr_ctrl register (see section 10.1.14 ). corresponding changes in bvalid will cause an rxcmd to be sent to the link with the alt_int bit asserted. fig 6. single and back-to-back rxcmds from the isp1507 to the link clock rxcmd data [ 7:0 ] rxcmd rxcmd 004aaa695 dir stp nxt single rxcmd back-to-back rxcmds turnaround turnaround turnaround turnaround cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 24 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver [1] !squelch indicates inactive squelch. !hs_differential_receiver _output indicates inactive hs _differential_receiver_output. [1] !squelch indicates inactive squelch. !hs_differential_receiver _output indicates inactive hs _differential_receiver_output. 9.5.2.2 v bus state encoding usb devices must monitor the v bus voltage for purposes such as overcurrent detection, starting a session and srp. the v bus state field in the rxcmd is an encoding of the voltage level on v bus . the a_vbus_vld, sess_vld and se ss_end indicators in the v bus state are directly taken from internal comparators built-in to the isp1507, and encoded as shown in ta b l e 9 and table 12 . an rxcmd may not be sent when exiting low-po wer mode or serial mode, if the interrupt condition is removed before exiting. note that v bus and fault share the same pin and cannot be simultaneously used. a_vbus_vld and fault will be interpre ted by the isp1507 as shown in figure 7 . a description on how to use and select the v bus state encoding is given in section 9.5.2.3 . table 10. linestate[1:0] encoding for upstream facing ports: peripherals dp_pulldown = 0. [1] mode full-speed high-speed chirp xcvrselect[1:0] 01, 11 00 00 termselect 1 0 1 linestate[1:0] 00 se0 squelch squelch 01 fs-j !squelch !squelch and hs_d ifferential_receiver_output 10 fs-k invalid !squelch and !hs_differential_receiver_output 11 se1 invalid invalid table 11. linestate[1:0] encoding fo r downstream facing ports: host dp_pulldown and dm_pulldown = 1. [1] mode low-speed full-speed high-speed chirp xcvrselect[1:0] 10 01, 11 00 00 termselect 1 1 0 0 opmode[1:0] x x 00, 01, 11 10 linestate[1:0] 00 se0 se0 squelch squelch 01 ls-k fs-j !squelch !squelch and hs_differential_receiver_output 10 ls-j fs-k invalid !squelch and !hs_differential_receiver_output 11 se1 se1 invalid invalid table 12. encoded v bus voltage state value v bus voltage sess_end sess_vld a_vbus_vld 00 v bus cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 26 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver otg devices: the isp1507 provides partial otg support. a low-power otg a-device that supplies less than 100 ma on v bus can connect the v bus power to the isp1507 v bus pin. the internal a_vbus_vld comparator c an be used. if the otg a-device provides more than 100 ma on v bus , an overcurrent detector must be used and section ? standard usb host controllers ? on page 25 applies. the otg a-device also uses sess_vld to detect when an otg b-de vice is initiating v bus pulsing srp. when an otg device is configured as an otg b-device, sess_vld must be used to detect when v bus is at a sufficient level for operati on. sess_end must be used to detect when v bus has dropped to a low level, allowing the b-device to safely initiate v bus pulsing srp. 9.5.2.4 rxevent encoding the rxevent field (see table 14 ) of the rxcmd informs the link of information related packets received on the usb bus. rxactive and rxerror are defined in usb 2.0 transceiver macrocell interface (utmi) specification ver. 1.05 . hostdisconnect is defined in utmi+ specification rev. 1.0 . a short definition is also given in the following subsections. rxactive: when the isp1507 has detected a sync pattern on the usb bus, it signals an rxactive event to the link. an rxactive ev ent can be communicated using two methods. the first method is for the isp1507 to simu ltaneously assert dir and nxt. the second method is for the isp1507 to send an rxcm d to the link with the rxactive field in rxevent bits set to logic 1. the link must be able to detect both method s. rxactive frames the receive packet from the first byte to the last byte. the link must assume that rxactive is set to logic 0 when indicated in an rxcmd or when dir is deasserted, wh ichever occurs first. the link uses rxactive to time high-speed packets and ensure that bus turnaround times are met. for more information on the usb packet timing, see section 9.8.1 . rxerror: when the isp1507 has detected an error while receiving a usb packet, it deasserts nxt and sends an rxcmd with the rxerror field set to logic 1. the received packet is no longer valid and must be dropped by the link. hostdisconnect: hostdisconnect is encoded into t he rxevent field of the rxcmd. hostdisconnect is valid only when the is p1507 is configured as a host (both dp_pulldown and dm_pulldown are set to logic 1), and indicates to the host controller when a peripheral is connected or disconnected. the host controller must enable hostdisconnect by setting the ho st_discon_r and host _discon_f bits in the usb_intr_en_r_e and usb_intr_en_f_e registers, respectively. changes in hostdisconnect will cause the phy to send an rxcmd to the link wit h the updated value. table 14. encoded usb event signals value rxactive rxerror hostdisconnect 00 0 0 0 01 1 0 0 11 1 1 0 10 x x 1 cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 27 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 9.6 register read and write operations figure 8 shows register read and write sequen ces. the isp1507 supports immediate addressing and extended addressing register op erations. extended register addressing is optional for links. note that regi ster operations will be aborte d if the isp150 7 unexpectedly asserts dir during the operation. when a register operation is aborted, the link must retry until successful. for more information on register operations, refer to utmi+ low pin interface (ulpi) specification rev. 1.1 . 9.7 usb reset and high-speed detection handshake (chirp) figure 9 shows the sequence of events for usb reset and high-speed detection handshake (chirp). the sequence is shown for hosts and peripherals. figure 9 does not show all rxcmd updates and timing is not to scale. the sequence is as follows: 1. usb reset: the host detects a peripheral at tachment as low-speed if dm is high and as full-speed if dp is high. if a host detec ts a full-speed peripheral, it resets the peripheral by writing to the function control register (see section 10.1.2 ). xcvrselect[1:0] = 00b (high-speed) and termselect = 0b are then set which drives se0 on the bus (dp and dm connected to ground through 45 ). the host also sets opmode[1:0] = 10b for correct chirp transmit and receive. the start of se0 is labeled t 0 . remark: to receive chirp signaling, the host must also consider the high-speed differential receiver output. the host cont roller must interpret linestate[1:0] as shown in ta b l e 11 . ad indicates the address byte, and d indicates the data byte. fig 8. example of register write, register read, extended register write and extended register read clock dir data[7:0] nxt 004aaa710 d txcmd (extw) ad d immediate register write txcmd (regw) txcmd (regr) d ad txcmd (extw) d stp extended register write immediate register read extended register read cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 28 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 2. high-speed detection handshake (chirp) a. peripheral chirp: after detecting se0 for no less than 2.5 s, if the peripheral is capable of high-speed, it sets xc vrselect[1:0] = 00b (high-speed) and opmode[1:0] = 10b (chirp). the peripher al immediately follows this with a txcmd (nopid), transmitting a chirp k for no less than 1 ms and ending no more than 7 ms after reset time t 0 . if the peripheral is in lo w-power mode, it must wake up its clock within 5.6 ms, leaving 200 s for the link to start transmitting the chirp k, and 1.2 ms for the chirp k to comp lete (worst case with 10 % slow clock). b. host chirp: if the host does not detect the peripheral chirp, it must continue asserting se0 until the end of reset. if the host detects the peripheral chirp k for no less than 2.5 s, then no more than 100 s after the bus leaves the chirp k state, the host sends a txcmd (nopid) with an alternating sequence of chirp ks and js. each chirp k or chirp j must last for no less than 40 s and no longer than 60 s. c. high-speed idle: the peripheral must detect a minimum of chirp k-j-k-j-k-j. each chirp k and chirp j must be detected for at least 2.5 s. the peripheral sets termselect = 0b and opmode[1:0] = 00 b after seeing the minimum chirp sequence. the peripheral is now in high-speed mode and sees !squelch (01b on linestate). when the peripheral sees squelch (10b on linestate), it knows that the host has completed chirp and waits for hi-speed usb traffic to begin. after transmitting the chirp sequence, the host changes opmode[1:0] to 00b and begins sending usb packets. for more information, refer to utmi+ low pin interface (ulpi) specification rev. 1.1 . cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 29 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver timing is not to scale. fig 9. usb reset and high-speed detection handshake (chirp) sequence 004aaa711 k data [ 7:0 ] k j txcmd nopid j ... txcmd (regw) txcmd (regw) se0 k dir 00 stp nxt xcvr select term select 01 (fs) 00 (hs) op mode 00 (normal) 01 (chirp) 00 (normal) line state j (01b) se0 (00b) peripheral chirp k (10b) squelch (00b) host chirp k (10b) or chirp j (01b) squelch (00b) ulpi host k data [ 7:0 ] k txcmd nopid k ... se0 txcmd (regw) 00 k j k j k j txcmd (regw) 00 dir stp nxt xcvr select 01 (fs) 00 (hs) term select op mode 00 (normal) 10 (chirp) 00 (normal) line state j (01b) se0 (00b) peripheral chirp k (10b) !squelch (01b) host chirp k or j (10b or 01b) squelch (00b) squelch (00b) dp dm ulpi peripheral usb signals usb reset high-speed detection handshake (chirp) peripheral chirp host chirp hs idle t 0 rxcmds cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 30 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 9.8 usb packet transmit and receive an example of a packet transmit and receive is shown in figure 10 . for details on usb packets, refer to utmi+ low pin interface (ulp i) specification rev. 1.1 . 9.8.1 usb packet timing 9.8.1.1 isp1507 pipeline delays the isp1507 delays are shown in ta b l e 1 5 . for a detailed descr iption, refer to utmi+ low pin interface (ulpi) specification rev. 1.1, section 3.8.2.6.2 . [1] according to utmi+ low pin interface (ulpi) specification rev. 1.1, section 3.8.2.6 , the tx and rx start or end delays must be used for high-speed inter-packet timing. if the link uses rxcmds for high-speed inter-pac ket timing, the result cannot be guaranteed . fig 10. example of using the isp1507 to transmit and receive usb data clock txcmd data data [ 7:0 ] turnaround rxcmd data turnaround dir stp nxt 004aab080 link sends txcmd isp1507 accepts txcmd link sends the next data; isp1507 accepts link signals end of data ulpi bus is idle isp1507 asserts dir, causing turnaround cycle isp1507 sends rxcmd (nxt low) isp1507 sends usb data (nxt high) isp1507 deasserts dir, causing turnaround cycle table 15. phy pipeline delays parameter name [1] high-speed phy delay full-speed phy delay low-speed phy delay rxcmd delay (j and k) 4 4 4 rxcmd delay (se0) 4 4 to 6 16 to 18 tx start delay 1 to 2 6 to 10 74 to 75 tx end delay (packets) 3 to 4 not applicable not applicable tx end delay (sof) 6 to 9 not applicable not applicable rx start delay 5 to 6 not applicable not applicable rx end delay 5 to 6 17 to 18 122 to 123 cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 31 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 9.8.1.2 allowed link decision time the amount of clock cycles allocated to the link to respond to a received packet and correctly receive back-to- back packets is given in table 16 . link designs must follow values given in ta b l e 1 6 for correct usb system operation. examples of high-speed packet sequences and timing are shown in figure 11 and figure 12 . for details, refer to utmi+ low pin interface (ulpi) spec ification rev. 1.1, section 3.8.2.6.3 . table 16. link decision times packet sequence high-speed link delay full-speed link delay low-speed link delay definition transmit-transmit (host only) 15 to 24 7 to 18 77 to 247 number of clock cycles a host link must wait before driving the txcmd for the second packet. in high-speed, the link starts counting from the assertion of stp for the first packet. in full-speed, the link starts counting from the rxcmd, indicating linestate has changed from se0 to j for the first packet. the timing given en sures inter-packet delays of 2 bit times to 6.5 bit times. receive-transmit (host or peripheral) 1 to 14 7 to 18 77 to 247 number of clock cycles the link must wait before driving the txcmd for the transmit packet. in high-speed, the link starts counting from the end of the receive packet; deassertion of dir or an rxcmd, indicating rxactive is low. in full-speed or low-speed, the link starts counting from the rxcmd, indicating linestate has changed from se0 to j for the receive packet. the timing given ensures inter-packet delays of 2 bit times to 6.5 bit times. receive-receive (peripheral only) 1 1 1 minimum number of clo ck cycles between consecutive receive packets. the link must be able to receive both packets. transmit-receive (host or peripheral) 92 80 718 host or peripheral transmits a packet and will time-out after this number of clock cycles if a response is not received. any subsequent transmission can occur after this time. cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 32 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 9.9 preamble preamble packets are headers to low-speed pa ckets that must travel over a full-speed bus, between a host and a hub. to enter preamble mode, the link sets xcvrselect[1:0] = 11b in the func_ctrl register (see section 10.1.2 ). when in fig 11. high-speed transmi t-to-transmit packet timing 004aaa712 dp or dm data eop idle sync clock d n ? 1 d n data [7:0] d0 txcmd d1 dir stp nxt tx end delay (two to five clocks) link decision time (15 to 24 clocks) tx start delay (one to two clocks) usb interpacket delay (88 to 192 high-speed bit times) fig 12. high-speed receive-to-transmit packet timing 004aaa713 dp or dm data eop idle sync clock d n ? 4 d n ? 3 data [7:0] d0 txcmd d1 dir stp nxt rx end delay (three to eight clocks) link decision time (1 to 14 clocks) tx start delay (one to two clocks) usb interpacket delay (8 to 192 high-speed bit times) d n ? 2 d n ? 1 d n turnaround cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 33 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver preamble mode, the isp1507 operates just as in full-speed mode, and sends all data with the full-speed rise time and fall time. wh enever the link transmits a usb packet in preamble mode, the isp1507 will automatically send a preamble header at full-speed bit rate before sending the link packet at lo w-speed bit rate. the isp1507 will ensure a minimum gap of four full-speed bit times betwe en the last bit of the full-speed pre pid and the first bit of the low-speed packet sync. the isp1507 will drive a j for at least one full-speed bit time after sending the pre pid, after which the pull-up resistor can hold the j state on the bus. an example transmit packet is shown in figure 13 . in preamble mode, the isp1507 can also receive low-speed packets from the full-speed bus. 9.10 usb suspend and resume 9.10.1 full-speed and low-speed host-initiated suspend and resume figure 14 illustrates how a host or a hub places a full-speed or low-spe ed peripheral into suspend and sometime later initiates resume signaling to wake up th e downstream peripheral. note that figure 14 timing is not to scale, and does not show all rxcmd linestate updates. the sequence of events for a host and a periphe ral, both with isp1507, is as follows: 1. idle: initially, the host and the peripheral are idle. the host has its 15 k pull-down resistors enabled (dp_pulldown and dm_pulldown are set to 1b) and 45 terminations disabled (termselect is set to 1b). the peripheral has the 1.5 k pull-up resistor connected to dp for full- speed or dm for low-speed (termselect is set to 1b). 2. suspend: when the peripheral sees no bus activity for 3 ms, it enters the suspend state. the peripheral link places the phy into low-power mode by clearing the suspendm bit in the func_ctrl register (see section 10.1.2 ), causing the phy to draw only suspend current. the host may or may not be powered down. dp and dm timing is not to scale. fig 13. preamble sequence clock d0 txcmd (low-speed packet id) d1 data[7:0] dir stp nxt 004aaa714 dp or dm fs sync fs pre id idle (min 4 fs bits) ls sync ls pid ls d0 ls d1 cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 34 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 3. resume k: when the host wants to wake up the peripheral, it sets opmode[1:0] to 10b and transmits a k for at least 20 ms. the peripheral link sees the resume k on linestate, and asserts st p to wake up the phy. 4. eop: when stp is asserted , the isp1507 on the host side automatically appends an eop of two bits of se0 at low-speed bit rate, followed by one bit of j. the isp1507 on the host side knows to add the eop because dp_pulldown and dm_pulldown are set to 1b for a host. after the eop is completed, the host link sets opmode[1:0] to 00b for normal operation. the peripheral link sees the eop and also resumes normal operation. cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 35 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 9.10.2 high-speed suspend and resume figure 15 illustrates how a host or a hub places a high-speed enabled peripheral into suspend and then initiates re sume signaling. the high-spee d peripheral will wake up and return to high-speed operations. note that figure 15 timing is not to scale, and does not show all rxcmd linestate updates. timing is not to scale. fig 14. full-speed suspend and resume data [ 7:0 ] k txcmd nopid k ... txcmd (regw) dir stp nxt opmode 00b 10b 00b k txcmd line state j k se0 j clock data [ 7:0 ] txcmd (regw) linestate j linestate k se0 j dir stp nxt opmode 00b 10b 00b suspendm line state j k se0 j dp dm 004aab123 fs or ls host (xcvrselect = 01b (fs) or 10b (ls), dp_pulldown = 1b, dm_pulldown = 1b, termselect = 1b) fs or ls peripheral (xcvrselect = 01b (fs) or 10b (ls), dp_pulldown = 0b, termselect = 1b) usb signals (only fs is shown) idle suspend resume k eop idle cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 36 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver the sequence of events related to a host and a peripheral, both with isp1507, is as follows: 1. high-speed idle: initially, the host and the peripheral are idle. the host has its 15 k pull-down resistors enabled (dp_pulldown and dm_pulldown are set to 1b) and 45 terminations enabled (termselect is set to 0b). the peripheral has its 45 terminations enabled (termselect is set to 0b). 2. full-speed suspend: when the peripheral sees no bus activity for 3 ms, it enters the suspend state. the peripheral link places the isp1507 into full-speed mode (xcvrselect is set to 01b), removes 45 terminations, and enables the 1.5 k pull-up resistor on dp (termselect is set to 1b). the peripheral link then places the isp1507 into low-power mode by cl earing suspendm, causing the isp1507 to draw only suspend current. the host also changes the isp1507 to full-speed (xcvrselect is set to 01b), removes 45 terminations (termselect is set to 1b), and then may or may not be powered down. 3. resume k: when the host wants to wake up the peripheral, it sets opmode to 10b and transmits a full-speed k for at least 20 ms. the peripheral link sees the resume k (10b) on linestate, and asserts stp to wake up the isp1507. 4. high-speed traffic: the host link sets high-speed (xcvrselect is set to 00b) and enables its 45 terminations (termselect is set to 0b). the peripheral link sees se0 on linestate and also sets high-speed (xcvrselect is set to 00b), and enables its 45 terminations (termselect is set to 0b). the host link sets opmode to 00b for normal high-speed operation. cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 37 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver timing is not to scale. fig 15. high-speed suspend and resume data [ 7:0 ] k txcmd nopid k ... txcmd (regw) dir stp nxt op mode 00b 10b 00b k txcmd (regw) clock data [ 7:0 ] txcmd (regw) linestate j linestate k se0 txcmd (regw) dir stp nxt op mode 00b 10b 00b suspendm line state dp dm 004aab124 ulpi hs host (dp_pulldown = 1b, dm_pulldown = 1b) ulpi hs peripheral (dp_pulldown = 0b) usb signals hs idle fs suspend resume k txcmd (regw) hs idle xcvr select 00b 01b 00b term select line state !squelch (01b) fs j (01b) !squelch (01b) squelch (00b) fs k (10b) xcvr select 00b 01b 00b term select !squelch (01b) squelch (00b) fs j (01b) !squelch (01b) squelch (00b) fs k (10b) squelch (00b) cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 38 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 9.10.3 remote wake-up the isp1507 supports peripherals that initiate remote wake-up resume. when placed into usb suspend, the peripheral link remembers at what speed it was originally operating. depending on the original speed, the link follows one of the protocols detailed here. in figure 16 , timing is not to scale, and not all rxcmd linestate updates are shown. the sequence of events related to a host and a peripheral, both with isp1507, is as follows: 1. both the host and the peripheral are assumed to be in low-power mode. 2. the peripheral begins remote wake-up by re-enabling its clock and setting its suspendm bit to 1b. 3. the peripheral begins driving k on the bus to signal resume. note that the peripheral link must assume that linestate is k ( 01b) while transmitti ng because it will not receive any rxcmds. 4. the host recogni zes the resume, re-enables its clock and sets its suspendm bit. 5. the host takes over resume driving within 1 ms of detecting the remote wake-up. 6. the peripheral stops driving resume. 7. the peripheral sees the host continuing to drive resume. 8. the host stops driving resume and the is p1507 automatically adds the eop to the end of resume. the peripheral recognizes the eop as the end of resume. 9. both the host and the peripheral revert to normal operation by writing 00b to opmode. if the host or the peripheral was previously in high-speed mode, it must revert to high-speed before the se0 of th e eop is completed. this can be achieved by writing xcvrselect[1:0] = 00b a nd termselect = 0b after linestate indicates se0. cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 39 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 9.11 no automatic sync and eop generation (optional) this setting allows the link to turn off the automatic sync and eop generation, and must be used for high-speed packets only. it is pr ovided for backward co mpatibility with legacy controllers that include sync and eop bytes in the data payload when transmitting packets. the isp1507 will not automatically generate the sync and eop patterns when opmode[1:0] is set to 11b. the isp1507 will still nrzi encode data and perform bit stuffing. an example of a sequence is shown in figure 17 . the link must always send packets using the txcmd (nopid) type. the isp1507 does not provide a mechanism to control bit stuffing in individu al bytes, but will automatically turn off bit stuffing for eop when stp is asserted with data set to feh. if data is set to 00h when stp is asserted, the timing is not to scale. fig 16. remote wake-up from low-power mode data [ 7:0 ] linestate txcmd regw txcmd regw 00h txcmd nopid dir stp nxt xcvr select 01b (fs), 10b (ls) 00b (hs only) term select op mode 10b 00b data [ 7:0 ] linestate txcmd regw rxcmd 00h txcmd nopid rxcmd rxcmd txcmd regw dir stp nxt xcvr select 00b (hs), 01b (fs), 10b (ls) 00b (hs only) term select op mode 10b 00b ulpi host ulpi peripheral 004aaa718 0b (hs only) 0b (hs only) cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 40 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver phy will not transmit any eop. the isp1507 will also detect if the pid byte is a5h, indicating an sof packet, and automatically send a long eop when stp is asserted. to transmit chirp and resume signaling, the link must set opmode[1:0] to 10b. 9.12 on-the-go operations on-the-go (otg) is a supplement to universal serial bus specification rev. 2.0 that allows a portable usb device to assume t he role of a limited usb host by defining improvements, such as a small connector and low power. non-portable devices, such as standard hosts and embedded hosts, can also benefit from otg features. the isp1507 otg phy is designed to support all the tasks specified in the otg supplement. the isp1507 provides the front- end analog support for host negotiation protocol (hnp) and session request prot ocol (srp) for dual-role devices. the supporting components include: ? voltage comparators ? a_vbus_vld ? sess_vld (session valid, can be used fo r both a-session and b-session valid) ? sess_end (session end) ? pull-up and pull-down resistors on dp and dm ? charge and discharge resistors on v bus for complete otg support, the system designer must add a v bus power supply and detect the value on the id pin of the usb cable. this is not provided on the isp1507. the following subsections describe how to use the isp1507 otg components. fig 17. transmitting usb packets withou t the automatic sync and eop generation clock data [7:0] txcmd 00h 00h 00h 80h pid d1 d2 d3 ... ... d n ? 1 feh d n dir stp nxt ulpi signals txvalid txready txbit stuff enable dp, dm idle sync pid idle eop data payload 004aab125 utmi+ equivalent signals usb bus cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 41 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 9.12.1 otg comparators the isp1507 provides comp arators that conform to on-the-go supplement to the usb 2.0 specification rev. 1.3 requirements of v a_vbus_vld , v a_sess_vld , v b_sess_vld and v b_sess_end . in this data sheet, v a_sess_vld and v b_sess_vld are combined into v b_sess_vld . comparators are described in section 7.6 . changes in comparator values are communicated to the link by rxcmds as described in section 9.5.2.2 . control over comparators is described in section 10.1.5 to section 10.1.8 . 9.12.2 pull-up and pull-down resistors the usb resistors on dp and dm can be used to initiate data-line pulsing srp. the link must set the required bus state using mode settings given in ta b l e 7 . 9.12.3 v bus charge and discharge resistors a pull-up resistor, r up(vbus) , is provided to perform v bus pulsing srp. a b-device is allowed to charge v bus above the session valid threshold to request the host to turn on the v bus power. a pull-down resistor, r dn(vbus) , is provided for a b-device to discharge v bus . this is done whenever the a-device turns off the v bus power. the b-device can use the pull-down resistor to ensure v bus is below v b_sess_end before starting a session. for details, refer to on-the-go supplement to the usb 2.0 specification rev. 1.3 . 9.13 serial modes the isp1507 supports both 6-pin serial mode and 3-pin serial mode, controlled by bits 6pin_fsls_serial and 3pin_fsls_seri al of the intf_ctrl register (see section 10.1.3 ). for details, refer to utmi+ low pin interface (ulpi) specification rev. 1.1, section 3.10 . figure 18 and figure 19 provide examples of 6-pin serial mode and 3-pin serial mode, respectively. cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 42 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver fig 18. example of transmit follow ed by receive in 6-pin serial mode data0 (tx_enable) data1 (tx_dat) data2 (tx_se0) data4 (rx_dp) data5 (rx_dm) data6 (rx_rcv) dp dm sync data eop transmit receive sync data eop 004aaa692 fig 19. example of transmit follow ed by receive in 3-pin serial mode data0 (tx_enable) data1 (tx_dat/ rx_rcv) dp data2 (tx_se0/ rx_se0) dm 004aaa693 sync data eop transmit receive sync data eop cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 43 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 9.14 aborting transfers the isp1507 supports aborting transfers on the ulpi bus. for details, refer to utmi+ low pin interface (ulpi) specific ation rev. 1.1, section 3.8.4 . 9.15 avoiding contention on the ulpi data bus because the ulpi data bus is bidirectional, avoid situations in which both the link and the phy simultaneously drive the data bus. the following points must be c onsidered while implementing the data bus drive control on the link. after power-up and clock stabilizatio n, default states are as follows: ? the isp1507 drives dir to low. ? the data bus is input to the isp1507. ? the ulpi link data bus is output, with all data bus lines driven to low. when the isp1507 wants to take control of t he data bus to initiate a data transfer, it changes the dir value from low to high. at this point, the link must disable its output buffers. this must be as fast as possible so the link must use a combin ational path from dir. the isp1507 will not immediatel y enable its output buffers, but will delay the enabling of its buffers until the next clock edge, avoiding bus contention. when the data transfer is no longer required by the isp1507, it changes dir from high to low and starts to immediately turn off its output drivers. the link senses the change of dir from high to low, but delays enabli ng its output buffers for one clock cycle, avoiding data bus contention. cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 44 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 10. register map [1] read (r): a register can be read. r ead-only if this is the only mode given. [2] write (w): the pattern on the data bus will be written over all bits of a register. [3] set (s): the pattern on the data bus is or-ed with and written to a register. [4] clear (c): the pattern on the data bus is a mask. if a bit in the mask is set, then the corresponding register bit will be s et to zero (cleared). [1] read (r): a register can be read. r ead-only if this is the only mode given. [2] write (w): the pattern on the data bus will be written over all bits of a register. [3] set (s): the pattern on the data bus is or-ed with and written to a register. [4] clear (c): the pattern on the data bus is a mask. if a bit in the mask is set, then the corresponding register bit will be s et to zero (cleared). table 17. immediate register set overview field name size (bit) address (6 bit) references r [1] w [2] s [3] c [4] vendor_id_low 8 00h - - - section 10.1.1 on page 45 vendor_id_high 8 01h - - - product_id_low 8 02h - - - product_id_high 8 03h - - - func_ctrl 8 04h to 06h 04h 05h 06h section 10.1.2 on page 45 intf_ctrl 8 07h to 09h 07h 08h 09h section 10.1.3 on page 46 otg_ctrl 8 0ah to 0ch 0ah 0bh 0ch section 10.1.4 on page 47 usb_intr_en_r_e 8 0dh to 0fh 0dh 0eh 0fh section 10.1.5 on page 48 usb_intr_en_f_e 8 10h to 12h 10h 11h 12h section 10.1.6 on page 49 usb_intr_stat 8 13h - - - section 10.1.7 on page 50 usb_intr_l 8 14h - - - section 10.1.8 on page 50 debug 8 15h - - - section 10.1.9 on page 51 scratch 8 16h to 18h 16h 17h 18h section 10.1.10 on page 51 reserved (do not use) - 19h to 2eh section 10.1.11 on page 51 access extended register set 8 - 2fh - - section 10.1.12 on page 51 vendor-specific registers 8 30h to 3ch section 10.1.13 on page 51 pwr_ctrl 8 3dh to 3fh section 10.1.14 on page 51 table 18. extended register set overview field name size (bit) address (6 bit) references r [1] w [2] s [3] c [4] maps to immediate register set above 8 00h to 3fh section 10.2 on page 52 reserved (do not use) 8 40h to ffh cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 45 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 10.1 immediate register set 10.1.1 vendor id and product id registers 10.1.1.1 vendor_id_low register ta b l e 1 9 shows the bit description of the register. 10.1.1.2 vendor_id_high register the bit description of the register is given in ta b l e 2 0 . 10.1.1.3 product_id_low register the bit description of the product_id_low register is given in table 21 . 10.1.1.4 product_id_high register the bit description of the register is given in ta b l e 2 2 . 10.1.2 func_ctrl register this register controls utmi function settings of the phy. the bit allocation of the register is given in ta b l e 2 3 . table 19. vendor_id_low - vendor id low re gister (address r = 00h) bit description legend: * reset value bit symbol access value description 7 to 0 vendor_id_ low[7:0] r cch* vendor id low : lower byte of the st-ericsson vendor id supplied by usb-if; has a fixed value of cch table 20. vendor_id_high - vendor id high register (address r = 01h) bit description legend: * reset value bit symbol access value description 7 to 0 vendor_id_ high[7:0] r 04h* vendor id high : upper byte of the st-ericsson vendor id supplied by usb-if; has a fixed value of 04h table 21. product_id_low - product id low re gister (address r = 02h) bit description legend: * reset value bit symbol access value description 7 to 0 product_id_ low[7:0] r 05h* product id low : lower byte of the st-ericsson product id number; has a fixed value of 05h table 22. product_id_high - pro duct id high register (addr ess r = 03h) bit description legend: * reset value bit symbol access value description 7 to 0 product_id_ high[7:0] r 15h* product id high : upper byte of the st-ericsson product id number; has a fixed value of 15h table 23. func_ctrl - function control register (address r = 04h to 06h, w = 04h, s = 05h, c = 06h) bit allocation bit 7 6 5 4 3 2 1 0 symbol reserved suspendm reset opmode[1:0] term select xcvrselect[1:0] reset 0 1000001 access r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 46 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 10.1.3 intf_ctrl register the intf_ctrl register enables alternative in terfaces. all of these modes are optional features provided for legacy link cores. setting more than one of these fields results in undefined behavior. table 25 provides the bit allocation of the register. table 24. func_ctrl - function cont rol register (address r = 04h to 06h , w = 04h, s = 05h, c = 06h) bit description bit symbol description 7 - reserved 6 suspendm suspend low : active low phy suspend. places the phy into low-power mode. the ph y will power down all blocks, except the full-speed receiver, otg comparators and ulpi pins. to come out of low-power mode, the link must assert stp. the phy will automatically clear this bit when it exits low-power mode. 0b ? low-power mode 1b ? powered (default) 5 reset reset : active high transceiver reset. after the link sets this bit, the phy will assert dir and reset the digital core. this does not reset the ulpi interface or the ulpi register set. when reset is completed, the phy will deassert di r and automatically clear this bit, followed by an rxcmd update to the link. 0b ? do not reset (default) 1b ? reset the link must wait for dir to deassert before using the ulpi bus. does not reset the ulpi interface or the ulpi register set. 4 to 3 opmode[1:0] operation mode : selects the required bit-encoding style during transmit. 00b ? normal operation (default) 01b ? non-driving 10b ? disable bit-stuffing and nrzi encoding 11b ? do not automatically add sync and eop when transmitting; must be used only for high-speed packets 2 termselect termination select : controls the internal 1.5 k full-speed pull-up resistor and 45 high-speed terminations. control over bus resistors changes, depending on xcvrselect[1:0], opmode[1:0], dp_pulldown and dm_pulldown, as shown in ta b l e 7 . 1 to 0 xcvrselect[1:0] transceiver select : selects the required transceiver speed. 00b ? enable the high-speed transceiver 01b ? enable the full-speed transceiver 10b ? enable the low-speed transceiver 11b ? enable the full-speed transceiver for low-speed packets (full-speed preamble is automatically prefixed) table 25. intf_ctrl - interface control register (address r = 07h to 09h, w = 07h, s = 08h, c = 09h) bit allocation bit 7 6 5 4 3 2 1 0 symbol intf_ prot_dis ind_pass thru ind_ compl reserved clock_ suspendm reserved 3pin_fsls _serial 6pin_fsls _serial reset 0 000 0 0 0 0 access r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 47 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 10.1.4 otg_ctrl register this register controls various otg functions of the isp1507. the bit allocation of the otg_ctrl register is given in ta b l e 2 7 . table 26. intf_ctrl - interface control register (address r = 07h to 09h, w = 07h, s = 08h, c = 09h) bit description bit symbol description 7intf_prot_dis interface protect disable : controls circuitry built into the isp1507 to protect the ulpi when the link 3-states stp and data[7:0]. when this bit is enabled, the isp1507 will automatically detect when t he link stops driving stp. 0b ? enables the interface protect circuit (defau lt). the isp1507 attaches a weak pull-up resistor on stp. if stp is unexpectedly high, the isp1507 attaches weak pull-down resistors on data[7:0], protecting data inputs. 1b ? disables the interface protect circuit, detaches weak pull-down resistors on data[7:0], and a weak pull-up resistor on stp. 6 ind_passthru indicator pass-through : the isp1507 does not support the qualification of an external fault with the internal v a_vbus_vld comparator. either a digital fault is input on the v bus /fault pin or the v bus power is connected to the v bus /fault pin, not both. this bit must always be set to logic 1. 0b ? not supported (default). 1b ? the complement output signal is not qualified with the internal a_vbus_vld comparator. the link must al ways set this bit to logic 1. 5 ind_compl indicator complement : informs the phy to invert the fault input signal, generating the complement output. for details, see section 9.5.2.2 . 0b ? the isp1507 will not invert the fault signal (default). 1b ? the isp1507 will invert the fault signal. 4- reserved 3 clock_suspendm clock suspend low : active low clock suspend. powers down the internal clock circuitry only. by default, the clock will not be powered in 6-pin serial mode or 3-pin serial mode. valid only in 6-pin serial mode and 3-pin serial mode. valid only when suspendm is set to logic 1, otherwise this bit is ignored. 0b ? clock will not be powered in 3-pin or 6-pin serial mode. 1b ? clock will be powered in 3-pin and 6-pin serial modes. 2- reserved 1 3pin_fsls_serial 3-pin full-speed low-speed serial mode : changes the ulpi to a 3-bit serial interface. the phy will automatically clear this bit when 3-pin serial mode is exited. 0b ? full-speed or low-speed packets are sent using the parallel interface. 1b ? full-speed or low-speed packets are sent using the 3-pin serial interface. 0 6pin_fsls_serial 6-pin full-speed low-speed serial mode : changes the ulpi to a 6-bit serial interface. the phy will automatically clear this bit when 6-pin serial mode is exited. 0b ? full-speed or low-speed packets are sent using the parallel interface. 1b ? full-speed or low-speed packets are sent using the 6-pin serial interface. cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 48 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 10.1.5 usb_intr_en_r_e register the bits in this register enable interrupts and rxcmds to be sent when the corresponding bits in the usb_intr_stat register change from logic 0 to logic 1. by default, all transitions are enabled. ta b l e 2 9 shows the bit allocation of the register. table 27. otg_ctrl - otg control register (address r = 0ah to 0ch, w = 0ah, s = 0bh, c = 0ch) bit allocation bit 7 6 5 4 3 2 1 0 symbol use_ext_ vbus_ind drv_ vbus_ext drv_ vbus chrg_ vbus dischrg_ vbus dm_pull down dp_pull down reserved reset 00000110 access r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c table 28. otg_ctrl - otg control register (address r = 0a h to 0ch, w = 0ah, s = 0bh, c = 0ch) bit description bit symbol description 7 use_ext_ vbus_ind use external v bus indicator : informs the phy to use an external v bus overcurrent indicator. 0b ? use the internal otg comparator. 1b ? use the external v bus valid indicator signal input from the fault pin. 6 drv_vbus_ext drive v bus external : controls the external v bus supply through the reset_n/psw_n pin. 0b ? do not drive psw_n to low, disabling v bus . 1b ? drive psw_n to low, enabling v bus . 5 drv_vbus drive v bus : signals the isp1507 to drive 5 v on v bus . if drv_vbus_ext is set to logic 1, then setting drv_vbus is optional. 4 chrg_vbus charge v bus : charges v bus through a resistor. used for the v bus pulsing srp. the link must first check that v bus is discharged (see the dischrg_vbus bit), and that both the dp and dm data lines have been low (se0) for 2 ms. 0b ? do not charge v bus . 1b ? charge v bus . 3 dischrg_vbus discharge v bus : discharges v bus through a resistor. if the link sets this bit to logic 1, it waits for an rxcmd indicating that sess_end has changed from 0 to 1, and then resets this bit to 0 to stop the discharge. 0b ? do not discharge v bus . 1b ? discharge v bus . 2 dm_pulldown dm pull down : enables the 15 k pull-down resistor on dm. 0b ? pull-down resistor is not connected to dm. 1b ? pull-down resistor is connected to dm. 1 dp_pulldown dp pull down : enables the 15 k pull-down resistor on dp. 0b ? pull-down resistor is not connected to dp. 1b ? pull-down resistor is connected to dp. 0 - reserved; writing logic 1 will give undefined results cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 49 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 10.1.6 usb_intr_en_f_e register the bits in this register enable interrupts and rxcmds to be sent when the corresponding bits in the usb_intr_stat register change from logic 1 to logic 0. by default, all transitions are enabled. see ta b l e 3 1 . table 29. usb_intr_en_r_e - usb interrupt enable rising edge register (address r = 0dh to 0fh, w = 0dh, s = 0eh, c = 0fh) bit allocation bit 7 6 5 4 3 2 1 0 symbol reserved sess_ end_r sess_ valid_r vbus_ valid_r host_ discon_r reset 00011111 access r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c table 30. usb_intr_en_r_e - usb interrupt enable rising edge register (address r = 0dh to 0fh, w = 0dh, s = 0eh, c = 0fh) bit description bit symbol description 7to4 - reserved 3 sess_end_r session end rise : enables interrupts and rxcmds for logic 0 to logic 1 transitions on sess_end. 2 sess_valid_r session valid rise : enables interrupts and rxcmds for logic 0 to logic 1 transitions on sess_vld. 1 vbus_valid_r v bus valid rise : enables interrupts and rxcmds for logic 0 to logic 1 transitions on a_vbus_vld. 0 host_discon_r host disconnect rise : enables interrupts and rxcmds for logic 0 to logic 1 transitions on host_discon. table 31. usb_intr_en_f_e - usb interrupt enable falling edge register (address r = 10h to 12h, w = 10h, s = 11h, c = 12h) bit allocation bit 7 6 5 4 3 2 1 0 symbol reserved sess_ end_f sess_ valid_f vbus_ valid_f host_ discon_f reset 00011111 access r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c table 32. usb_intr_en_f_e - usb interrupt enable falling edge register (address r = 10h to 12h, w = 10h, s = 11h, c = 12h) bit description bit symbol description 7to4 - reserved 3 sess_end_f session end fall : enables interrupts and rxcmds for logic 1 to logic 0 transitions on sess_end. 2 sess_valid_f session valid fall : enables interrupts and rxcmds for logic 1 to logic 0 transitions on sess_vld. 1 vbus_valid_f v bus valid fall : enables interrupts and rxcmds for logic 1 to logic 0 transitions on a_vbus_vld. 0 host_discon_f host disconnect fall : enables interrupts and rxcmds for logic 1 to logic 0 transitions on host_discon. cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 50 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 10.1.7 usb_intr_stat register this register (see ta b l e 3 3 ) indicates the current value of the interrupt source signal. 10.1.8 usb_intr_l register the bits of the usb_intr_l register are automatically set by the isp1507 when an unmasked change occurs on the corresponding in terrupt source signal. the isp1507 will automatically clear all bits when the link reads this register, or when the phy enters low-power or serial mode. remark: it is optional for the link to read this register when the clock is running because all signal information will au tomatically be sent to the link through the rxcmd byte. the bit allocation of this register is given in ta b l e 3 5 . table 33. usb_intr_stat - usb interrupt status register (address r = 13h) bit allocation bit 7 6 5 4 3 2 1 0 symbol reserved sess_ end sess_ valid vbus_ valid host_ discon reset xxx00000 access rrrrrrrr table 34. usb_intr_stat - usb interrupt status register (address r = 13h) bit description bit symbol description 7to4 - reserved 3 sess_end session end : reflects the current value of the session end voltage comparator. 2 sess_valid session valid : reflects the current value of the session valid voltage comparator. 1 vbus_valid v bus valid : reflects the current value of the v bus valid voltage comparator. 0 host_discon host disconnect : reflects the current value of the host disconnect detector. table 35. usb_intr_l - usb interrupt latch register (address r = 14h) bit allocation bit 7 6 5 4 3 2 1 0 symbol reserved sess_ end_l sess_ valid_l vbus_ valid_l host_ discon_l reset 00000000 access rrrrrrrr table 36. usb_intr_l - usb interrupt latch register (address r = 14h) bit description bit symbol description 7to4 - reserved 3 sess_end_l session end latch : automatically set when an unm asked event occurs on sess_end. cleared when this register is read. 2 sess_valid_l session valid latch : automatically set when an unmas ked event occurs on sess_vld. cleared when this register is read. 1 vbus_valid_l v bus valid latch : automatically set when an unmasked event occurs on a_vbus_vld. cleared when this register is read. 0 host_discon_l host disconnect latch : automatically set when an unmasked event occurs on host_discon. cleared when this register is read. cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 51 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 10.1.9 debug register the bit allocation of the debug register is given in ta b l e 3 7 . this register indicates the current value of signals useful for debugging. 10.1.10 scratch register ta b l e 3 9 shows the bit description of the scratch register. it is an empty register for testing purposes. 10.1.11 reserved registers 19h to 2eh are not implemented. operating on these addresses will have no effect on the phy. 10.1.12 access extended register set address 2fh does not contain register data. instead it links to the extended register set. the immediate register set maps to the lower end of the extended register set. 10.1.13 vendor-specific registers addresses 30h to 3fh contain vendor-specific registers. 10.1.14 pwr_ctrl register ta b l e 4 0 provides the bit allocation of the pwr_ctrl register. table 37. debug - debug register (address r = 15h) bit allocation bit 7 6 5 4 3 2 1 0 symbol reserved line state1 line state0 reset 00000000 access rrrrrrrr table 38. debug - debug register (address r = 15h) bit description bit symbol description 7to2 - reserved 1 linestate1 line state 1 : contains the current value of linestate 1 0 linestate0 line state 0 : contains the current value of linestate 0 table 39. scratch - scratch register (address r = 16h to 18h, w = 16h, s = 17h, c = 18h) bit description legend: * reset value bit symbol access value description 7to0 scratch [7:0] r/w/s/c 00h* scratch : this is an empty register byte for testing purposes. software can read, write, set and clear this register. the functionality of the phy will not be affected. table 40. pwr_ctrl - power control register (address r = 3dh to 3fh, w = 3dh, s = 3eh, c = 3fh) bit allocation bit 7 6 5 4 3 2 1 0 symbol reserved bvalid_ fall bvalid_ rise reserved ignore_ reset reset 00000000 access r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c r/w/s/c cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 52 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 10.2 extended register set addresses 00h to 3fh of the extended register se t directly map to the immediate set. this means a read, write, set or clear operation to these extend ed addresses will operate on the immediate register set. addresses 40h to ffh are not implemented. operating on these addresses may result in undefined behavior of the phy. table 41. pwr_ctrl - power control register (address r = 3dh to 3fh, w = 3dh, s = 3eh, c = 3fh) bit description bit symbol description 7 to 4 - reserved; the link must never write logic 1 to these bits. 3bvalid_fall bvalid fall : enables rxcmds for high-to-low tr ansitions on bvalid. when bvalid changes from high to low, the isp1507 will send an rxcmd to the link with the alt_int bit set to logic 1. this bit is optional and is not necessary for otg devices. this bit is provided for debugging purposes. the session valid comparator must be used instead. 2 bvalid_rise bvalid rise : enables rxcmds for low-to-high transitions on bvalid. when bvalid changes from low to high, the isp1507 will se nd an rxcmd to the link with the alt_int bit set to logic 1. this bit is optional and is not necessary for otg devices. this bit is provided for debugging purposes. the session valid comparator must be used instead. 1- reserved 0 ignore_reset ignore reset : selects between the reset_n and psw_n functions of the reset_n/psw_n pin. the link must set this bit to logic 1, if psw_n is used in a ganged mode configuration. 0b ? the reset_n/psw_n pin behaves as an acti ve-low reset input (reset_n). this is the default setting. 1b ? the reset_n/psw_n pin beha ves as an active-low po wer switch output (psw_n). cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 53 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 11. electrostatic discharge (esd) 11.1 esd protection the pins that are connected to the usb connector (dp, dm, v bus and gnd) have a minimum of 4 kv esd protection. capacitors 0.1 f and 1 f must be connected in parallel from v bus to gnd to achieve this 4 kv esd protection (see figure 20 ). remark: capacitors 0.1 f and 1 f are also required by universal serial bus specification rev. 2.0 . for details on the requirements for c vbus , see section 16 . 11.2 esd test conditions a detailed report on test setup and results is available on request. fig 20. human body esd test model r d 1500 r c 1 m high voltage dc source 0.1 f1 f v bus device under test c s 100 pf storage capacitor charge current limit resistor discharge resistance gnd a b 004aaa881 cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 54 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 12. limiting values [1] maximum value may not exceed 4.6 v. [2] includes voltage on outputs in 3-state mode. [3] only valid when the v cc(i/o) supply voltage is present. [4] the isp1507 has been tested according to the additional requirements listed in universal serial bus specification rev. 2.0, section 7.1.1 . the short circuit withstand test and the ac stress test were performed for 24 hours, and the isp1507 was found to be fully operational after the test completed. [5] equivalent to discharging a 100 pf capacitor through a 1.5 k resistor (human body model jesd22-a114d). 13. recommended operating conditions [1] v cc(i/o) must be less than or equal to v cc . table 42. limiting values in accordance with the absolute ma ximum rating system (iec 60134). symbol parameter conditions min max unit v cc supply voltage ? 0.5 +4.6 v v cc(i/o) input/output supply voltage ? 0.5 +4.6 v v i input voltage on pins stp, data[7:0] and reset_n/psw_n ? 0.5 v cc(i/o) +0.5 [1] [2] [3] v on pin v bus /fault ? 0.5 +6.0 v on pin xtal1 ? 0.5 +2.5 v on pins dp and dm [4] ? 0.5 +4.6 v v esd electrostatic discharge voltage on pins dp, dm, v bus and gnd; i li <1 a [5] ? 4+4 kv on all other pins; i li < 1 a ? 2+2 kv i lu latch-up current ? 100 +100 ma v lu latch-up voltage - 4.6 v t stg storage temperature ? 40 +125 c table 43. recommended operating conditions symbol parameter conditions min typ max unit v cc supply voltage 3.0 3.3 3.6 v v cc(i/o) input/output supply voltage [1] 1.65 - 3.6 v v i input voltage on pins stp, data[7:0] and reset_n/psw_n 0- v cc(i/o) v on pin v bus /fault 0 - 5.5 v on pins dp and dm 0 - 3.6 v on pin xtal1 0 - 1.95 v t amb ambient temperature ? 40 +25 +85 c t j junction temperature ? 40 - +125 c cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 55 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 14. static characteristics [1] a continuous stream of 1 kb packets with minimum inter-pac ket gap and all data bits set to logic 0 for continuous toggling. table 44. static characte ristics: supply pins v cc = 3.0 v to 3.6 v; v cc(i/o) = 1.65 v to 3.6 v; t amb = ? 40 cto+85 c; unless otherwise specified. typical values are at v cc = 3.3 v; v cc(i/o) = 3.3 v; t amb = +25 c; unless otherwise specified. symbol parameter conditions min typ max unit v (reg3v3) voltage on pin reg3v3 3.0 3.3 3.6 v v (reg1v8) voltage on pin reg1v8 1.65 1.8 1.95 v v por(trip) power-on reset trip voltage 1.0- 1.5v i cc supply current low-power mode; v bus valid detector disabled; 1.5 k pull-up resistor on pin dp disconnected -3085 a low-power mode; v bus valid detector disabled; 1.5 k pull-up resistor on pin dp connected - 215 280 a full-speed continuous data transmit; 50 pf load on pins dp and dm [1] -15-ma full-speed continuous data receive [1] -11-ma high-speed continuous data transmit; 45 load on pins dp and dm to ground [1] -48-ma high-speed continuous data receive [1] -28-ma i cc(i/o) supply current on pin v cc(i/o) static current; i/o pins are idle - - 1 a table 45. static characteri stics: digital pins (clock, dir, st p, nxt, data[7:0], reset_n/psw_n) v cc = 3.0 v to 3.6 v; v cc(i/o) = 1.65 v to 3.6 v; t amb = ? 40 cto+85 c; unless otherwise specified. typical values are at v cc = 3.3 v; v cc(i/o) = 3.3 v; t amb = +25 c; unless otherwise specified. symbol parameter conditions min typ max unit input levels v il low-level input voltage - - 0.3 v cc(i/o) v v ih high-level input voltage 0.7 v cc(i/o) -- v i il low-level input current v i = 0 v - - 1 a i ih high-level input current v i = v cc(i/o) --1 a i li input leakage current ? 1+0.1+1 a output levels v oh high-level output voltage i oh = ? 4ma v cc(i/o) ? 0.4 - - v v ol low-level output voltage i ol = +4 ma - - 0.4 v i oh high-level output current v o = v cc(i/o) ? 0.4 v ? 4-- ma i ol low-level output current v o = 0.4 v +4 - - ma i oz off-state output current 0 v < v o cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 57 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver [1] for high-speed usb and full-speed usb. resistance r up(dp) pull-up resistance on pin dp 1425 1500 1575 high-speed usb transceiver input levels (differential receiver) v hssq high-speed squelch detection threshold voltage (differential signal amplitude) 100 - 150 mv v hsdsc high-speed disconnect detection threshold voltage (differential signal amplitude) 525 - 625 mv v hsdi high-speed differential input sensitivity | v dp ? v dm | 100 - - mv v hscm high-speed data signaling common mode voltage range (guideline for receiver) includes v di range ? 50 - +500 mv v hsoi high-speed idle level voltage ? 10 - +10 mv v hsol high-speed data signaling low-level voltage ? 10 - +10 mv output levels v hsoh high-speed data signaling high-level voltage 360 - 440 mv v chirpj chirp j level (differential voltage) 700 - 1100 mv v chirpk chirp k level (differential voltage) ? 900 - ? 500 mv leakage current i lz off-state leakage current ? 1- +1 a capacitance c in input capacitance pin to gnd - - 5 pf resistance r dn(dp) pull-down resistance on pin dp 14.25 15 15.75 k r dn(dm) pull-down resistance on pin dm 14.25 15 15.75 k termination z o(drv)(dp) driver output impedance on pin dp steady-state drive [1] 40.5 45 49.5 z o(drv)(dm) driver output impedance on pin dm steady-state drive [1] 40.5 45 49.5 z inp input impedance exclusive of pull-up/pull-down (for low-/full-speed) 10 - - m table 47. static characteristics: analog i/o pins (dp, dm) ?continued v cc = 3.0 v to 3.6 v; v cc(i/o) = 1.65 v to 3.6 v; t amb = ? 40 cto+85 c; unless otherwise specified. typical values are at v cc = 3.3 v; v cc(i/o) = 3.3 v; t amb = +25 c; unless otherwise specified. symbol parameter conditions min typ max unit cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 58 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver table 48. static characteristics: v bus comparators v cc = 3.0 v to 3.6 v; v cc(i/o) = 1.65 v to 3.6 v; t amb = ? 40 cto+85 c; unless otherwise specified. typical values are at v cc = 3.3 v; v cc(i/o) = 3.3 v; t amb = +25 c; unless otherwise specified. symbol parameter conditions min typ max unit v a_vbus_vld a-device v bus valid voltage 4.4 4.5 4.65 v v b_sess_vld b-device session valid voltage for a-device and b-device 0.8 1.6 2.0 v v hys(b_sess_vld) b-device session valid hysteresis voltage 70 140 200 mv v b_sess_end b-device session end voltage 0.2 0.5 0.8 v table 49. static characteristics: v bus resistors v cc = 3.0 v to 3.6 v; v cc(i/o) = 1.65 v to 3.6 v; t amb = ? 40 cto+85 c; unless otherwise specified. typical values are at v cc = 3.3 v; v cc(i/o) = 3.3 v; t amb = +25 c; unless otherwise specified. symbol parameter conditions min typ max unit r up(vbus) pull-up resistance on pin v bus connect to pin reg3v3 when chrg_vbus is logic 1 281 680 - r dn(vbus) pull-down resistance on pin v bus connect to gnd when dischrg_vbus is logic 1 656 850 - r i(idle)(vbus) idle input resistance on pin v bus 40 57 80 k table 50. static characterist ics: resistor reference v cc = 3.0 v to 3.6 v; v cc(i/o) = 1.65 v to 3.6 v; t amb = ? 40 cto+85 c; unless otherwise specified. typical values are at v cc = 3.3 v; v cc(i/o) = 3.3 v; t amb = +25 c; unless otherwise specified. symbol parameter conditions min typ max unit v o(rref) output voltage on pin rref suspendm is logic 1 - 1.22 - v cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 59 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 15. dynamic characteristics [1] the internal pll is triggered only on the positive edge from t he crystal oscillator. therefore, the duty cycle is not critic al. table 51. dynamic character istics: reset and clock v cc = 3.0 v to 3.6 v; v cc(i/o) = 1.65 v to 3.6 v; t amb = ? 40 cto+85 c; unless otherwise specified. typical values are at v cc = 3.3 v; v cc(i/o) = 3.3 v; t amb = +25 c; unless otherwise specified. symbol parameter conditions min typ max unit reset t w(por) internal power-on reset pulse width 0.2 - - s t w(reg1v8_h) reg1v8 high pulse width 2 - - s t w(reg1v8_l) reg1v8 low pulse width 11 - - s t w(reset_n) external reset_n pulse width 200 - - ns t regup regulator start-up time 4.7 f 20 % capacitor each on pins reg1v8 and reg3v3 v cc =3.3v; t amb = +25 c-2-ms v cc =3.0v; t amb = ? 40 c--50ms crystal or clock applied to xtal1 f i(xtal1) input frequency on pin xtal1 isp1507cbs - 19.2 - mhz isp1507dbs - 26 - mhz t jit(i)(xtal1)rms rms input jitter on pin xtal1 isp1507cbs - - 200 ps isp1507dbs - - 300 ps i(xtal1) input duty cycle on pin xtal1 applicable only when clock is applied on pin xtal1 [1] -50-% f i(xtal1) input frequency tolerance on pin xtal1 - 50 200 ppm t r(xtal1) rise time on pin xtal1 only for square wave input - - 5 ns t f(xtal1) fall time on pin xtal1 only for square wave input - - 5 ns v (xtal1)(p-p) peak-to-peak voltage on pin xtal1 only for square wave input 0.566 - 1.95 v output clock characteristics f o(clock) output frequency on pin clock - 60 - mhz t jit(o)(clock)rms rms output jitter on pin clock - - 500 ps o(clock) output clock duty cycle on pin clock 45 50 55 % t startup(pll) pll startup time - 650 - s t startup(o)(clock) output clock start-up time measured from power good or assertion of pin stp 450 650 900 s cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 60 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver table 52. dynamic characteristics: digital i/o pins v cc = 3.0 v to 3.6 v; t amb = ? 40 cto+85 c; unless otherwise specified. symbol parameter conditions min typ max unit v cc(i/o) = 1.65 v to 1.95 v t su(data) data set-up time with respect to the rising edge of pin clock 20 pf total external load per pin 5.7 - - ns t h(data) data hold time with respect to the rising edge of pin clock 20 pf total external load per pin 0- - ns t d(data) data output delay with respect to the rising edge of pin clock 20 pf total external load per pin --7.8ns t su(stp) stp set-up time with respect to the rising edge of pin clock 20 pf total external load per pin 4.5 - - ns t h(stp) stp hold time with respect to the rising edge of pin clock 20 pf total external load per pin 0- - ns t d(dir) dir output delay with respect to the rising edge of pin clock 20 pf total external load per pin --8.9ns t d(nxt) nxt output delay with respect to the rising edge of pin clock 20 pf total external load per pin --8.9ns v cc(i/o) =3.0vto3.6v t su(data) data set-up time with respect to the rising edge of pin clock 30 pf total external load per pin 3.3 - - ns t h(data) data hold time with respect to the rising edge of pin clock 30 pf total external load per pin 0.8 - - ns t d(data) data output delay with respect to the rising edge of pin clock 30 pf total external load per pin --5.5ns t su(stp) stp set-up time with respect to the rising edge of pin clock 30 pf total external load per pin 3.4 - - ns t h(stp) stp hold time with respect to the rising edge of pin clock 30 pf total external load per pin 0.8 - - ns t d(dir) dir output delay with respect to the rising edge of pin clock 30 pf total external load per pin --6.6ns t d(nxt) nxt output delay with respect to the rising edge of pin clock 30 pf total external load per pin --6.6ns table 53. dynamic characteristics : analog i/o pins (dp, dm) v cc = 3.0 v to 3.6 v; v cc(i/o) = 1.65 v to 3.6 v; t amb = ? 40 cto+85 c; unless otherwise specified. symbol parameter conditions min typ max unit high-speed driver t hsr rise time (10 % to 90 %) 500 - - ps t hsf fall time (10 % to 90 %) 500 - - ps full-speed driver t fr rise time c l = 50 pf; 10 % to 90 % of | v oh ? v ol | 4- 20ns t ff fall time c l = 50 pf; 10 % to 90 % of | v oh ? v ol | 4- 20ns t frfm differential rise and fall time matching excluding the first transition from the idle state 90 - 111.1 % cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 61 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver v crs output signal crossover voltage excluding the first transition from the idle state 1.3 - 2.0 v low-speed driver t lr transition time: rise time c l = 200 pf to 600 pf; 1.5 k pull-up resistor on pin dm enabled; 10 % to 90 % of | v oh ? v ol | 75 - 300 ns t lf transition time: fall time c l = 200 pf to 600 pf; 1.5 k pull-up resistor on pin dm enabled; 10 % to 90 % of | v oh ? v ol | 75 - 300 ns t lrfm rise and fall time matching t lr /t lf ; excluding the first transition from the idle state 80 - 125 % driver timing t plh(drv) driver propagation delay (low to high) tx_dat, tx_se0 to dp, dm; see figure 22 --20ns t phl(drv) driver propagation delay (high to low) tx_dat, tx_se0 to dp, dm; see figure 22 --20ns t phz driver disable delay from high level tx_enable to dp, dm; see figure 23 --12ns t plz driver disable delay from low level tx_enable to dp, dm; see figure 23 --12ns t pzh driver enable delay to high level tx_enable to dp, dm; see figure 23 --20ns t pzl driver enable delay to low level tx_enable to dp, dm; see figure 23 --20ns receiver timing differential receiver t plh(rcv) receiver propagation delay (low to high) dp, dm to rx_rcv, rx_dp and rx_dm; see figure 24 --20ns t phl(rcv) receiver propagation delay (high to low) dp, dm to rx_rcv, rx_dp and rx_dm; see figure 24 --20ns single-ended receiver t plh(se) single-ended propagation delay (low to high) dp, dm to rx_rcv, rx_dp and rx_dm; see figure 24 --20ns t phl(se) single-ended propagation delay (high to low) dp, dm to rx_rcv, rx_dp and rx_dm; see figure 24 --20ns table 53. dynamic characteristics : analog i/o pins (dp, dm) ?continued v cc = 3.0 v to 3.6 v; v cc(i/o) = 1.65 v to 3.6 v; t amb = ? 40 cto+85 c; unless otherwise specified. symbol parameter conditions min typ max unit cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 62 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 15.1 ulpi timing ulpi timing requirements are given in figure 25 . this timing app lies to synchronous mode only. all timing is measured with respec t to the isp1507 clock pin. all signals are clocked on the rising edge of clock. fig 21. rise time and fall time fig 22. timing of tx_dat and tx_se0 to dp and dm fig 23. timing of tx_enable to dp and dm fig 24. timing of dp and dm to rx_rcv, rx_dp and rx_dm 004aaa861 v ol t hsr , t fr , t lr t hsf , t ff , t lf v oh 90 % 10 % 10 % 90 % 004aaa573 v ol v oh t phl(drv) t plh(drv) v crs v crs 0.9 v 0.9 v 1.8 v 0 v logic input differential data lines 004aaa574 v ol v oh t pzh t pzl t phz t plz v oh ? 0.3 v v ol + 0.3 v v crs 0.9 v 0.9 v 1.8 v 0 v logic input differential data lines t plh(se) t phl(se) 004aaa575 v ol v oh t phl(rcv) t plh(rcv) v crs v crs 0.9 v 0.9 v 2.0 v 0.8 v logic output differential data lines fig 25. ulpi timing clock control in (stp) data in (8-bit) t su(stp) t h(stp) t su(data) t h(data) control out (dir, nxt) data out (8-bit) 004aaa722 t d(dir) , t d(nxt) t d(data) t d(dir) , t d(nxt) cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 63 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 16. application information [1] for detailed information and alternative interface options, refer to the interfacing to the isp1507 (an10080) application note. [2] for more information, contact murata. table 54. recommended list of materials designator [1] application value comment c bypass highly recommended for all applications 0.1 f- c filter highly recommended for all applications 4.7 f 20 %; use a low esr capacitor (0.2 to 2 ) for best performance - c vbus mandatory for peripherals 0.1 f and 1 fto10 f in parallel - mandatory for host 0.1 f and 120 f 20 % (min) in parallel - mandatory for otg 0.1 f and 1 fto6.5 f in parallel - r pullup recommended; for applications with an external v bus supply controlled by psw_n 4.7 k (recommended) maximum value is determined by the voltage drop on psw_n caused by leakage into psw_n and the external supply control pin r rref mandatory in all applications 12 k ? 1% - r vbus strongly recommended for peripheral or external 5 v applications only 1k ? 5% - r xtal required only for applications driving a square wave into the xtal1 pin 47 k ? 5 % used to avoid floating input on the xtal1 pin xtal crystal is used 19.2 mhz c l =10pf; r s <220 ; c xtal =18pf 26 mhz c l =10pf; r s <130 ; c xtal =18pf - cstce26m0xk2***-r0 [2] c xtal is not required c (xtal)sq required only for applications driving a square wave into the xtal1 pin that has a dc offset 100 pf used to ac couple the input square wave to the xtal1 pin xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 64 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver (1) frequency is version dependent: isp1507cbs: 19.2 mhz; isp1507dbs: 26 mhz. fig 26. using the isp1507 with a usb host controller; ext ernal 5 v source with built-in fault and external crystal isp1507 data1 v cc(i/o) rref dm dp v cc data2 data3 v cc(i/o) data4 clock data5 data6 data7 nxt stp 7 6 5 4 3 1 15 16 17 18 19 21 20 23 22 24 v bus /fault reg3v3 xtal1 xtal2 11 10 9 8 dir reg1v8 reset_n/ psw_n 12 13 14 host controller usb standard-a receptacle v bus d ? d+ gnd 4 3 2 1 data0 data2 data3 data4 data5 data6 data7 nxt clock stp dir v cc(i/o) v cc gnd (die pad) data1 2 data0 004aab081 xtal (1) +5 v in fault on out v bus switch r pullup c bypass c bypass c filter c bypass c filter c vbus c xtal c xtal r rref 5 6 7 8 shield shield shield shield c bypass c bypass xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 65 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver (1) frequency is version dependent: isp1507cbs: 19.2 mhz; isp1507dbs: 26 mhz. fig 27. using the isp1507 with a peripheral controller; external square wave input on pin xtal1 isp1507 data0 v cc(i/o) rref dm dp data2 data3 v cc(i/o) clock data4 data5 data6 data7 nxt 7 6 5 4 3 1 16 15 18 19 20 21 23 22 24 004aab082 v bus /fault reg3v3 xtal1 xtal2 11 10 9 8 stp dir reg1v8 reset_n/ psw_n 12 13 14 17 peripheral controller usb standard-b receptacle v bus d _ d+ gnd 4 3 2 1 data0 data1 data2 data3 data4 data5 data6 data7 clock nxt stp dir v cc(i/o) v cc gnd (die pad) data1 2 v cc c bypass c filter c bypass c filter c bypass r rref 5 6 7 8 shield shield shield shield r xtal c (xtal)sq f i(xtal1) (1) c bypass c bypass c vbus r vbus cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 66 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 17. package outline fig 28. package outline sot616-3 (hvqfn24) 0.5 1 0.2 a 1 e h b unit y e references outline version european projection issue date iec jedec jeita mm 4.1 3.9 d h 2.75 2.45 y 1 4.1 3.9 2.75 2.45 e 1 2.5 e 2 2.5 0.30 0.18 c 0.05 0.00 0.05 0.1 dimensions (mm are the original dimensions) sot616-3 mo-220 04-11-19 05-03-10 - - - - - - 0.5 0.3 l 0.1 v 0.05 w 0 2.5 5 mm scale sot616-3 hvqfn24: plastic thermal enhanced very thin quad flat package; no leads; 24 terminals; body 4 x 4 x 0.85 mm a (1) max. a a 1 c detail x y y 1 c e l e h d h e e 1 b 712 24 19 18 13 6 1 x d e c b a e 2 terminal 1 index area terminal 1 index area a c c b v m w m 1/2 e 1/2 e e (1) note 1. plastic or metal protrusions of 0.075 mm maximum per side are not included. d (1) cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 67 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 18. abbreviations table 55. abbreviations acronym description asic application-specif ic integrated circuit atx analog usb transceiver cd-rw compact disc-rewritable eop end-of-packet esd electrostatic discharge esr effective series resistance fs full-speed hbm human body model hnp host negotiation protocol hs high-speed id identification iec international electrotechnical commission ls low-speed mo magneto-optical nrzi non-return-to-zero inverted otg on-the-go pcb printed-circuit board pda personal digital assistant phy physical layer pid packet identifier pld programmable logic device pll phase-locked loop por power-on reset rohs restriction of hazardous substances rxcmd receive command se0 single-ended zero sof start-of-frame srp session request protocol stb set-top box sync synchronous ttl transistor-transistor logic txcmd transmit command usb universal serial bus usb-if usb implementers forum ulpi utmi+ low pin interface utmi usb 2.0 transceiver macrocell interface utmi+ usb 2.0 transceiver macrocell interface plus cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 68 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 19. references [1] universal serial bus specification rev. 2.0 [2] on-the-go supplement to the usb 2.0 specification rev. 1.3 [3] utmi+ low pin interface (u lpi) specification rev. 1.1 [4] utmi+ specification rev. 1.0 [5] usb 2.0 transceiver macrocell inte rface (utmi) specification ver. 1.05 [6] electrostatic discharge (esd) sensit ivity testing human body model (hbm) (jesd22-a114d) [7] interfacing to the isp1507 (an10080) 20. revision history table 56. revision history revision release date data sheet status change notice 4 20100520 product data sheet - modifications: ? table 44 ? static characteristics: supply pins ? : removed i cc(i/o)(stat) . 3 20091022 product data sheet - 2 20090120 product data sheet - 1 20080528 product data sheet - cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 69 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 21. tables table 1. ordering information . . . . . . . . . . . . . . . . . . . . .3 table 2. pin description . . . . . . . . . . . . . . . . . . . . . . . . . .5 table 3. ulpi signal description . . . . . . . . . . . . . . . . . .13 table 4. signal mapping during low-power mode . . . . .14 table 5. signal mapping for 6-pin serial mode . . . . . . .15 table 6. signal mapping for 3-pin serial mode . . . . . . .16 table 7. operating states and their corresponding resistor settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 table 8. txcmd byte format . . . . . . . . . . . . . . . . . . . . .22 table 9. rxcmd byte format . . . . . . . . . . . . . . . . . . . .23 table 10. linestate[1:0] encoding for upstream facing ports: peripherals . . . . . . . . . . . . . . . . . . . . . . .24 table 11. linestate[1:0] encoding for downstream facing ports: host . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 table 12. encoded v bus voltage state . . . . . . . . . . . . . .24 table 13. v bus indicators in rxcmd required for typical applications . . . . . . . . . . . . . . . . . . . . . . . . . . .25 table 14. encoded usb event signals . . . . . . . . . . . . . .26 table 15. phy pipeline delays . . . . . . . . . . . . . . . . . . . .30 table 16. link decision times . . . . . . . . . . . . . . . . . . . . .31 table 17. immediate register set overview . . . . . . . . . . .44 table 18. extended register set overview . . . . . . . . . . . .44 table 19. vendor_id_low - vendor id low register (address r = 00h) bit descrip tion . . . . . . . . . . .45 table 20. vendor_id_high - vendor id high register (address r = 01h) bit descrip tion . . . . . . . . . . .45 table 21. product_id_low - product id low register (address r = 02h) bit descrip tion . . . . . . . . . . .45 table 22. product_id_high - product id high register (address r = 03h) bit descrip tion . . . . . . . . . . .45 table 23. func_ctrl - function control register (address r = 04h to 06h, w = 04h, s = 05h, c = 06h) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 table 24. func_ctrl - function control register (address r = 04h to 06h, w = 04h, s = 05h, c = 06h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 table 25. intf_ctrl - interface control register (address r = 07h to 09h, w = 07h, s = 08h, c = 09h) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 table 26. intf_ctrl - interface control register (address r = 07h to 09h, w = 07h, s = 08h, c = 09h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 table 27. otg_ctrl - otg cont rol register (address r = 0ah to 0ch, w = 0ah, s = 0bh, c = 0ch) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 table 28. otg_ctrl - otg cont rol register (address r = 0ah to 0ch, w = 0ah, s = 0bh, c = 0ch) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 table 29. usb_intr_en_r_e - usb interrupt enable rising edge register (address r = 0dh to 0fh, w = 0dh, s = 0eh, c = 0fh) bit allocation . . . .49 table 30. usb_intr_en_r_e - usb interrupt enable rising edge register (address r = 0dh to 0fh, w = 0dh, s = 0eh, c = 0fh) bit description . .49 table 31. usb_intr_en_f_e - usb interrupt enable falling edge register (address r = 10h to 12h, w = 10h, s = 11h, c = 12h) bit allocation . . . . 49 table 32. usb_intr_en_f_e - usb interrupt enable falling edge register (address r = 10h to 12h, w = 10h, s = 11h, c = 12h) bit description . . . 49 table 33. usb_intr_stat - usb interrupt status register (address r = 13h) bit allocation . . . . . . . . . . . 50 table 34. usb_intr_stat - usb interrupt status register (address r = 13h) bit description . . . . . . . . . . 50 table 35. usb_intr_l - usb interrupt latch register (address r = 14h) bit allocation . . . . . . . . . . . 50 table 36. usb_intr_l - usb interrupt latch register (address r = 14h) bit description . . . . . . . . . . 50 table 37. debug - debug register (address r = 15h) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 table 38. debug - debug register (address r = 15h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 table 39. scratch - scratch register (address r = 16h to 18h, w = 16h, s = 17h, c = 18h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 table 40. pwr_ctrl - power control register (address r = 3dh to 3fh, w = 3dh, s = 3eh, c = 3fh) bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 table 41. pwr_ctrl - power control register (address r = 3dh to 3fh, w = 3dh, s = 3eh, c = 3fh) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 table 42. limiting values . . . . . . . . . . . . . . . . . . . . . . . . 54 table 43. recommended operating conditions . . . . . . . 54 table 44. static characteristics: supply pins . . . . . . . . . . 55 table 45. static characteristics: digital pins (clock, dir, stp, nxt, data[7:0], reset_n/psw_n) . . . 55 table 46. static characteristics: pin v bus /fault . . . . . . 56 table 47. static characteristics: analog i/o pins (dp, dm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 table 48. static characteristics: v bus comparators . . . . 58 table 49. static characteristics: v bus resistors . . . . . . . . 58 table 50. static characteristics: resistor reference . . . . . 58 table 51. dynamic characteristics: reset and clock . . . . 59 table 52. dynamic characteristics: digital i/o pins . . . . . 60 table 53. dynamic characteristics: analog i/o pins (dp, dm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 table 54. recommended list of materials . . . . . . . . . . . . 63 table 55. abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 67 table 56. revision history . . . . . . . . . . . . . . . . . . . . . . . . 68 cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 70 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 22. figures fig 1. block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 fig 2. pin configuration hvqfn24; top view . . . . . . . . . .5 fig 3. internal power-on reset timing . . . . . . . . . . . . . . .18 fig 4. power-up and reset sequence required before the ulpi bus is ready for use . . . . . . . . . . . . . . . . . .20 fig 5. interface behavior with respect to reset_n . . .21 fig 6. single and back-to-back rxcmds from the isp1507 to the link. . . . . . . . . . . . . . . . . . . . . . . .23 fig 7. rxcmd a_vbus_vld indicator source . . . . . . .25 fig 8. example of register wr ite, register read, extended register write and extended register read . . . . . .27 fig 9. usb reset and high-speed detection handshake (chirp) sequence . . . . . . . . . . . . . . . . . . . . . . . . .29 fig 10. example of using the isp1507 to transmit and receive usb data . . . . . . . . . . . . . . . . . . . . . . . . .30 fig 11. high-speed transmit-to-transmit packet timing . .32 fig 12. high-speed receive-to-transmit packet timing . . .32 fig 13. preamble sequence . . . . . . . . . . . . . . . . . . . . . . .33 fig 14. full-speed suspend and resume . . . . . . . . . . . . .35 fig 15. high-speed suspend and resume . . . . . . . . . . . .37 fig 16. remote wake-up from low-power mode . . . . . . .39 fig 17. transmitting usb packets without the automatic sync and eop generation . . . . . . . . . . . . . . . . .40 fig 18. example of transmit followed by receive in 6-pin serial mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 fig 19. example of transmit followed by receive in 3-pin serial mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 fig 20. human body esd test model . . . . . . . . . . . . . . .53 fig 21. rise time and fall time . . . . . . . . . . . . . . . . . . . . .62 fig 22. timing of tx_dat and tx_se0 to dp and dm. .62 fig 23. timing of tx_enable to dp and dm. . . . . . . . .62 fig 24. timing of dp and dm to rx_rcv, rx_dp and rx_dm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 fig 25. ulpi timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 fig 26. using the isp1507 with a usb host controller; external 5 v source with built-in fault and external crystal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 fig 27. using the isp1507 with a peripheral controller; external square wave input on pin xtal1 . . . . . .65 fig 28. package outline sot616-3 (hvqfn24) . . . . . . .66 cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 71 of 73 continued >> isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 23. contents 1 general description . . . . . . . . . . . . . . . . . . . . . . 1 2 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4 ordering information . . . . . . . . . . . . . . . . . . . . . 3 5 block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4 6 pinning information . . . . . . . . . . . . . . . . . . . . . . 5 6.1 pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 6.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5 7 functional description . . . . . . . . . . . . . . . . . . . 7 7.1 ulpi controller . . . . . . . . . . . . . . . . . . . . . . . . . 7 7.2 usb serializer and deserializer. . . . . . . . . . . . . 7 7.3 hi-speed usb (usb 2.0) atx . . . . . . . . . . . . . 7 7.4 voltage regulator. . . . . . . . . . . . . . . . . . . . . . . . 8 7.5 crystal oscillator and pll . . . . . . . . . . . . . . . . . 8 7.6 v bus comparators. . . . . . . . . . . . . . . . . . . . . . . 8 7.6.1 v bus valid comparator . . . . . . . . . . . . . . . . . . . 8 7.6.2 session valid comparator . . . . . . . . . . . . . . . . . 9 7.6.3 session end comparator. . . . . . . . . . . . . . . . . . 9 7.7 srp charge and discharge resistors . . . . . . . . 9 7.8 band gap reference voltage . . . . . . . . . . . . . . . 9 7.9 power-on reset . . . . . . . . . . . . . . . . . . . . . . . . . 9 7.10 detailed description of pins. . . . . . . . . . . . . . . . 9 7.10.1 data[7:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 7.10.2 v cc(i/o) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.10.3 rref . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.10.4 dp and dm . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.10.5 v cc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.10.6 v bus /fault . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.10.6.1 v bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7.10.6.2 fault (external overcu rrent or fault detector) 10 7.10.7 reg3v3 and reg1v8 . . . . . . . . . . . . . . . . . . 11 7.10.8 xtal1 and xtal2 . . . . . . . . . . . . . . . . . . . . . 11 7.10.9 reset_n/psw_n . . . . . . . . . . . . . . . . . . . . . 11 7.10.9.1 reset_n . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7.10.9.2 psw_n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7.10.10 dir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 7.10.11 stp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 7.10.12 nxt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 7.10.13 clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 7.10.14 gnd (die pad). . . . . . . . . . . . . . . . . . . . . . . . . 12 8 modes of operation . . . . . . . . . . . . . . . . . . . . . 13 8.1 ulpi modes . . . . . . . . . . . . . . . . . . . . . . . . . . 13 8.1.1 synchronous mode. . . . . . . . . . . . . . . . . . . . . 13 8.1.2 low-power mode . . . . . . . . . . . . . . . . . . . . . . 14 8.1.3 6-pin full-speed or low-speed serial mode . . . 15 8.1.4 3-pin full-speed or low-speed serial mode . . . 15 8.2 usb and otg state transitions . . . . . . . . . . . 16 9 protocol description . . . . . . . . . . . . . . . . . . . . 18 9.1 ulpi references . . . . . . . . . . . . . . . . . . . . . . . 18 9.2 power-on reset (por) . . . . . . . . . . . . . . . . . 18 9.3 power-up, reset and bus idle sequence. . . . . 18 9.3.1 interface protection . . . . . . . . . . . . . . . . . . . . 20 9.3.2 interface behavior wit h respect to reset_n 21 9.4 v bus power and fault detection . . . . . . . . . . . 21 9.4.1 driving 5 v on v bus . . . . . . . . . . . . . . . . . . . . 21 9.4.2 fault detection . . . . . . . . . . . . . . . . . . . . . . . . 21 9.5 txcmd and rxcmd . . . . . . . . . . . . . . . . . . . 22 9.5.1 txcmd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 9.5.2 rxcmd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 9.5.2.1 linestate encoding . . . . . . . . . . . . . . . . . . . . . 23 9.5.2.2 v bus state encoding. . . . . . . . . . . . . . . . . . . . 24 9.5.2.3 using and selecting the v bus state encoding 25 9.5.2.4 rxevent encoding . . . . . . . . . . . . . . . . . . . . . 26 9.6 register read and write operations . . . . . . . . 27 9.7 usb reset and high-speed detection handshake (chirp). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 9.8 usb packet transmit and receive. . . . . . . . . . 30 9.8.1 usb packet timing . . . . . . . . . . . . . . . . . . . . . 30 9.8.1.1 isp1507 pipeline delays . . . . . . . . . . . . . . . . 30 9.8.1.2 allowed link decision time . . . . . . . . . . . . . . . 31 9.9 preamble . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 9.10 usb suspend and resume . . . . . . . . . . . . . . . 33 9.10.1 full-speed and low-speed host-initiated suspend and resume . . . . . . . . . . . . . . . . . . . . . . . . . . 33 9.10.2 high-speed suspend and resume . . . . . . . . . 35 9.10.3 remote wake-up . . . . . . . . . . . . . . . . . . . . . . 38 9.11 no automatic sync and eop generation (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 9.12 on-the-go operations . . . . . . . . . . . . . . . . . . 40 9.12.1 otg comparators . . . . . . . . . . . . . . . . . . . . . 41 9.12.2 pull-up and pull-down resistors . . . . . . . . . . . 41 9.12.3 v bus charge and discharge resistors . . . . . . . 41 9.13 serial modes . . . . . . . . . . . . . . . . . . . . . . . . . 41 9.14 aborting transfers. . . . . . . . . . . . . . . . . . . . . . 43 9.15 avoiding contention on the ulpi data bus . . . 43 10 register map . . . . . . . . . . . . . . . . . . . . . . . . . . 44 10.1 immediate register set . . . . . . . . . . . . . . . . . . 45 10.1.1 vendor id and product id registers . . . . . . . . 45 10.1.1.1 vendor_id_low register. . . . . . . . . . . . . . 45 10.1.1.2 vendor_id_high register . . . . . . . . . . . . . 45 10.1.1.3 product_id_low register . . . . . . . . . . . . 45 10.1.1.4 product_id_high register . . . . . . . . . . . . 45 10.1.2 func_ctrl register. . . . . . . . . . . . . . . . . . . 45 cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 72 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver 10.1.3 intf_ctrl register . . . . . . . . . . . . . . . . . . . . 46 10.1.4 otg_ctrl register . . . . . . . . . . . . . . . . . . . . 47 10.1.5 usb_intr_en_r_e register . . . . . . . . . . . . . 48 10.1.6 usb_intr_en_f_e register . . . . . . . . . . . . . 49 10.1.7 usb_intr_stat register . . . . . . . . . . . . . . . 50 10.1.8 usb_intr_l register . . . . . . . . . . . . . . . . . . . 50 10.1.9 debug register . . . . . . . . . . . . . . . . . . . . . . . 51 10.1.10 scratch register . . . . . . . . . . . . . . . . . . . . . 51 10.1.11 reserved . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 10.1.12 access extended register set . . . . . . . . . . . . . 51 10.1.13 vendor-specific registers . . . . . . . . . . . . . . . . 51 10.1.14 pwr_ctrl register . . . . . . . . . . . . . . . . . . . . 51 10.2 extended register set . . . . . . . . . . . . . . . . . . . 52 11 electrostatic discharge (esd) . . . . . . . . . . . . 53 11.1 esd protection . . . . . . . . . . . . . . . . . . . . . . . . 53 11.2 esd test conditions . . . . . . . . . . . . . . . . . . . . 53 12 limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 54 13 recommended operating conditions. . . . . . . 54 14 static characteristics. . . . . . . . . . . . . . . . . . . . 55 15 dynamic characteristics . . . . . . . . . . . . . . . . . 59 15.1 ulpi timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 16 application information. . . . . . . . . . . . . . . . . . 63 17 package outline . . . . . . . . . . . . . . . . . . . . . . . . 66 18 abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 67 19 references . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 20 revision history . . . . . . . . . . . . . . . . . . . . . . . . 68 21 tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 22 figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 23 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 cd00222690 ? st-ericsson 2010. all rights reserved. product data sheet rev. 04 ? 20 may 2010 73 of 73 isp1507c; isp1507d ulpi hs usb host and peripheral transceiver please read carefully: the contents of this document are subject to change without prior notice. st-ericsson makes no representation or warranty of an y nature whatsoever (neither expressed nor implied) with respect to the matters addressed in this document, including but not limited to warranties of merchantability or fitness for a particular purpose, interpretability or interoperability or, against infringement of third par ty intellectual property rights, and in no event shall st-ericsson be liable to any party for any direct, indirect, incidental and or consequential dama ges and or loss whatsoever (including but not limited to monetary losses or loss of data), that might arise from the use of this document or th e information in it. st-ericsson and the st-ericsson logo are trademarks of the st-ericsson group of companies or used under a license from stmicroelectronics nv or telefonaktiebolaget lm ericsson. all other names are the property of their respective owners. ? st-ericsson, 2010 - all rights reserved contact information at www.stericsson.com under contacts www.stericsson.com |
Price & Availability of ISP1507DBSUM
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |