? constan t curren t mod e output ? flicke r fre e design ? plasti c housin g wit h clas s ii design ? built-i n activ e pfc function ? n o loa d powe r consumption<0.5w(blank-type), standb y powe r consumption<0.5w( da -type) ? functio n options : 2 i n 1 dimmin g (dim-to-off); auxiliar y dc output ; dal i ? 3 year s warranty mode l encoding descriptio n features application s ? led pane l lightin g ? led floo d lighting ? indoo r led lighting rate d outpu t current(350/500/700/1050/1400ma) rate d wattage serie s name - 500 idlc - 45 file name: IDLC-45-spec 2017-07-20 a idlc -4 5 serie s i s a 45 w led ac / dc drive r featurin g th e constan t curren t mod e outpu t wit h flicker fre e design. idlc -4 5 operate s fro m 90~295 vac an d offer s model s wit h differen t rate d current rangin g betwee n 350m a an d 1400ma . thank s t o th e efficienc y u p t o 86% , wit h th e fanles s design , th e entir e serie s i s abl e t o operat e fo r -20 ~+85 cas e temperatur e unde r fre e ai r convection . idlc -4 5 i s equippe d wit h variou s functio n options , suc h a s dimmin g methodologies , s o a s t o provid e th e optima l desig n flexibilit y fo r lightin g system . f m m selv functio n options type blank function note i n stock i n stock 45w constant current mode led driver i d l c - 4 5 s e r i e s 2 i n 1 dimmin g (0~10vd c an d 10 v pwm) (fo r da-typ e only) da dal i contro l technology a:auxiliar y d c output(12v@50ma) :none { note : th e dal i contro l model(d a type ) onl y fo r idlc-4 5 no n auxiliar y d c outpu t models.
specification file name: IDLC-45-spec 2017-07-20 model output setup time note.4 frequency range power factor (typ.) efficiency (typ.) ac current input inrush current (typ.) leakage current working humidity storage temp ., humidity temp . coefficient vibration mtbf dimension others note packing short circuit <0.75ma / 277 vac 20 ~ 90% rh non-condensing -40 ~ +80 , 10 ~ 95% rh 0.03%/ (0 ~ 40 ) 10 ~ 500hz, 2g 10min./1cycle, period for 60min. each along x, y, z axes 408.8khrs min. mil - hdbk -217f (25 ) 1 . al l parameter s not speciall y mentione d ar e measure d a t 230 vac input , rate d curren t an d 25 o f ambien t temperature. 2 . pleas e refe r t o " driving methods of led module " . 3 . de-ratin g ma y b e neede d unde r lo w inpu t voltages . pleas e refe r t o static characteristic section s fo r details. 4 . lengt h o f se t u p tim e i s measure d a t col d firs t start . turnin g on / off th e drive r ma y lea d t o increas e o f th e se t u p time. 5 . ther e i s n o desig n o f shor t circui t protectio n fo r th e auxiliar y dc output ; thi s functio n ca n no t b e use d whe n dimmin g inpu t terminals( dim +, dim - ) ar e shor t circui t o r whe n i t i s n o loa d o r shor t circui t a t output(vo+,vo-). 6 . th e drive r i s considere d a s a componen t tha t wil l b e operate d i n combinatio n wit h fina l equipment . sinc e emc performanc e wil l b e affecte d b y th e complet e installation , th e fina l equipmen t manufacturer s mus t re-qualif y emc directiv e o n th e complet e installatio n again. 7 . th e dal i versio n drive r doe s no t suppor t th e bi t 1 : lam p failur e i n th e comman d 14 4 quer y statu s o f th e dal i standard. 0.22kg; 54pcs/ 13kg/ 0.93 cuft environment safety & emc protection withstand voltage isolation resistance i/p-o/p:3.75 kvac i/p-o/p:100m ohms / 500 vdc / 25 / 70% rh safety standards compliance to en 55015, en 61000-3-2 class c (@load R 60%) ; en 61000-3-3, gb 17743, gb 17625.1 emc immunity emc emission 120*75*25mm(l*w*h) hiccup mode,auto-recovery after fault condition is removed for da type hiccup mode,re-power on to recovery for other type compliance to en 61000-4-2,3,4,5,6,8,11; en 61547, light industry level(surge immunity:line-line:1 kv ) ul 8750, csa c22.2 no .250.13-12; enec en 61347-1 & en 61347-2-13 independent, en 62384, gb 19510.1, gb 19510.14 approved total harmonic distortion voltage range note.3 idlc -45 -350 idlc -45 -700 idlc -45 -1400 350ma 700ma 1400ma 33.25w 44.8w 44.8w 118v 500ms / 230 vac 1200ms/115 vac 47 ~ 63hz pf >0.95/115 vac , pf >0.92/230 vac , pf >0.9/277 vac @full load (please refer to " power factor ( pf ) characteristic " section) 86% 85% 83% 0.6a/115 vac 0.4a/230 vac 0.3a/277 vac cold start 30a(twidth= s measured at 50% ipeak) at 230 vac 100 ; per nema 410 57 ~ 95v 38 ~ 64v 19 ~ 32v 84v 50v idlc -45 -500 500ma 45w 85% 54 ~ 90v 115v idlc -45 -1050 1050ma 45.15w 84% 26 ~ 43v 63v rated current rated power current tolerance constant current region note.2 open circuit voltage (max.) current ripple 7.0% 5% max. @rated current thd < 20%(@load R 60%/115 vac ,230 vac ; @load R 75%/277 vac ) (please refer to total harmonic distortion section) max . no. of psu s on 16a circuit breaker 32 units (circuit breaker of type b) / 32 units (circuit breaker of type c) at 230 vac (please refer to " static characteristic " section) 90 ~ 295 vac 127 ~ 417 vdc auxiliary dc output note.5 nominal 12v(deviation 11.4~12.6)@50ma for IDLC-45a only 45w constant current mode led driver i d l c - 4 5 s e r i e s no load power consumption<0.5w for blank-type,<1.2w for IDLC-45a standby power consumption<0.5w for da -type no load / standby power consumption working temp . max . case temp . tcase=-20 ~ +85 (please refer to output load vs temperature section) tcase=+85 dali standards compliance to iec 62386-101, 102 for da -type only
file name: IDLC-45-spec 2017-07-20 fosc : 70 kh z block diagram dim +( da +) dim -( da -) detection circuit emi filter rectifiers power switching filter & rectifiers rectifiers vo+ aux +(for IDLC-45a) vo- i/p control & current limit pwm & pfc o.l.p. aux -(for IDLC-45a) 45w constant current mode led driver i d l c - 4 5 s e r i e s driving methods of led module this series works in constant current mode to directly drive the led s. typical output current normalized by rated current (%) in the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. should there be any compatibility issues, please contact mean well . 100 60 (min.) vo(%) 50 100 io(%) constant current area hiccup protection
dimming operation 2 in 1 dimming function ? output constant current level can be adjusted by applying one of the two methodologies between dim + and dim -: 0 ~ 10 vdc , or 10v pwm signal. ? direct connecting to led s is suggested. it is not suitable to be used with additional drivers. applying additive 0 ~ 10 vdc applying additive 10v pwm signal (frequency range 300hz ~ 3 kh z): note : 1. min. dimming level is about 8% and the output current is not defined when 0%< i out<8%. 2. the output current could drop down to 0% when dimming input is about 0vdc or 10v pwm signal with 0% duty cycle. vo+ vo- dim + dim - + + + - - - do not connect " dim - to vo- additive voltage vo+ vo- dim + dim - + + - - do not connect " dim - to vo- additive pwm signal 0v 1v 2v 3v 4v 5v 6v 7v 8v 9v 10v 10% 0% 20% 30% 40% 50% 60% 70% 80% 90% 100% output current (%) 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 10% 0% 20% 30% 40% 50% 60% 70% 80% 90% 100% output current (%) dimming input: additive voltage duty cycle of additive 10v pwm signal dimming input file name: IDLC-45-spec 2017-07-20 45w constant current mode led driver i d l c - 4 5 s e r i e s dim +( da +) dim -( da -) acn acl tb 1 acn acl vo+ vo- tb 2 dali interface (primary side; for da-type) ? apply dali signal between da+ and da- . ? dali protocol comprises 16 groups and 64 addresses. ? first step is fixed at 8% of output.
0.7 0.75 0.8 0.85 0.9 0.95 1 50% 60% 70% 80% 90% 100% 115v 230v 277v 76 78 80 82 84 86 88 90 50% 60% 70% 80% 90% 100% 277v 230v 115v 0 2 4 6 8 10 12 14 16 50% 60% 70% 80% 90% 100% 277v 230v 115v file name: IDLC-45-spec 2017-07-20 pf load output load vs temperature static characteristic total harmonic distortion ( thd ) power factor ( pf ) characteristic de-rating is needed under low input voltage. efficiency vs load idlc -45 series possess superior working efficiency that up to 86% can be reached in field applications. 350ma model,tcase at 75 350ma model,tcase at 75 efficiency (%) thd (%) load (45w) load (%) ( horizontal ) -20 -10 0 10 20 30 40 20 40 60 80 100 90~295 vac for 350ma model,200~295 vac for others 90~200 vac for models other than 350ma model input voltage (v) load (%) 90 295 100 90 80 70 60 50 40 135 180 for others for 350ma model 200 load 45w constant current mode led driver i d l c - 4 5 s e r i e s load (%) ( horizontal ) -20 -10 0 15 30 45 60 85 20 40 60 80 100 90~295 vac for 350ma model,200~295 vac for others 90~200 vac for models other than 350ma model ambient temperature,ta ( ) tcase at 75 tcase ( )
file name: IDLC-45-spec 2017-07-20 case no. idlc -45a unit:mm mechanical specification 45w constant current mode led driver i d l c - 4 5 s e r i e s installation manual please refer to : http://www.meanwell.com/webnet/search/installationsearch.html 30 30 3 25 120 6.5 6.5 6.5 6.5 75 2 1 tb 2 tb 1 ? : max. case temperature tc tc 4 3 2 1 4 3 6 5 2 * 4.3 IDLC-45 terminal pin no. assignment( tb 2) pin no. 1 2 3 4 assignment dim +( da +) vo- dim -( da -) vo+ terminal pin no. assignment( tb 1) pin no. 1 2 assignment acl acl 3 4 acn acn IDLC-45a terminal pin no. assignment( tb 2) pin no. pin no. 1 2 3 4 5 6 assignment assignment dim + vo- aux + aux - dim - vo+
|
