View LTL307JGD-041A_9003125.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

lite-on dcc release lite-on technology corp. / optoelectronics no.90,chien 1 road, chung ho, new taipei city 23585, taiwan, r.o.c. tel: 886-2-2222-6181 fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto through hole lamp product data sheetLTL307JGD-041A spec no.: ds20-2010-0116effective date: 03/29/2012revision: a bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4
lite - on technology corporation . p r o p e r t y o f l i t e - o n o n l y features * lead (pb) free product C rohs compliant. * high luminous intensity output. * low power consumption. * high efficiency. * versatile mounting on p.c. board or panel. * i.c. compatible/low current requirement. * popular t - 1 3/4 diameter. packag e dimensions part no. lens source color ltl307jgd - 041a green diffused alingap green notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25mm(.010") unless otherwise noted. 3. protruded resin under flange is 1.0mm( .04") max. 4 . lead spacing is measured where the leads emerge from the package. 5 . specifications are subject to change without notice. part no. : ltl307jgd - 041a page : 1 of 1 1 bns - od - c131/a4
lite - on technology corporation . p r o p e r t y o f l i t e - o n o n l y absolute maximum ratings at t a =25 c parameter maximum rating unit power dissipation 75 mw peak forward current (1/10 duty cycle, 0.1ms pulse width) 60 ma dc forward current 30 ma derating linear from 50 c 0.4 ma/ c reverse voltage 5 v operating temperature range - 40 c to + 8 0 c storage temperature range - 55 c to + 100 c lead soldering temperature [2 mm(.08 ") from body] 260 c for 5 seconds max. part no. : ltl307jgd - 041a page : 2 of 1 1 bns - od - c131/a4
lite - on technology corporation . p r o p e r t y o f l i t e - o n o n l y electrical / optical characteristics at t a = 25 c parameter symbol min. typ. max. unit test condition luminous intensity i v 65 110 180 mcd i f = 20ma note 1 ,4 viewing angle 2 1/2 50 deg note 2 (fig. 6 ) peak emission wavelength p 5 75 nm measurement @peak (fig.1) dominant wavelength d 566 572 578 nm i f = 20ma note 3 spectral line half - width ? 11 nm forward voltage v f 2.1 2. 4 v i f = 20ma reve rse current i r 100 a v r = 5 v note:1. luminous intensity is measured with a light sensor and filter combination that approximates the cie (commission international de l'eclairage) eye - response curve. 2. 1/2 is the off - axis an gle at which the luminous intensity is half the axial luminous intensity. 3. the dominant wavelength, d is derived from the cie chromaticity diagram and represents the single wavelength which defines the color of the device. 4. the iv guarantee should be added 15% . part no. : ltl307jgd - 041a page : 3 of 1 1 bns - od - c131/a4
lite - on technology corporation . p r o p e r t y o f l i t e - o n o n l y typical electrical / optical characteristics curves ( 25 c ambient temperature unless otherwise noted) part no. : ltl307jgd - 041a page : 4 of 1 1 bns - od - c131/a4
lite - on technology corporation . p r o p e r t y o f l i t e - o n o n l y features * compatible with radial lead automatic insertion equipment. * most radial lead plastic lead lamps available packaged in tape and folding. * 5mm (0.197") formed lead spacing availabl e. * folding packaging simplifies handling and testing. * ammo packing series lamp type 24 led+gap. package dimensions specification item symbol minimum maximum mm inch mm inch tape feed hole diameter d 3.8 0.149 4.2 0.1 65 component lead pitch f 4.8 0.188 5.8 0.228 front to rear deflection h -- -- 2.0 0.078 height of seating plane h 15.5 0.610 16.5 0.649 feed hole to bottom of component h1 21.5 0.846 23.5 0.925 feed hole to overall component height h2 29.8 1.173 32.4 1.276 ++ lead length after component height l w0 11.0 0.433 feed hole pitch p 12.4 0.488 13.0 0.511 lead location p1 3.15 0.124 4.55 0.179 center of component location p2 5.05 0.198 7.65 0.301 total tape thickness t -- -- 0.90 0.035 feed hole location w0 8.5 0.334 9.75 0.384 adhesive tape width w1 1 4 .5 0.571 1 5 .5 0.610 adhesive tape position w2 0 0 3.0 0.118 tape width w3 17.5 0.689 19.0 0.748 part no. : ltl307jgd - 041a page : 5 of 1 1 bns - od - c131/a4
lite - on technology corporation . p r o p e r t y o f l i t e - o n o n l y packing spec 2 , 000 pcs per inner carton 10 inner car tons per outer carton total 20 , 000 pcs per outer carton in every shipping lot, only the last pack will be non - full packing part no. : ltl307jgd - 041a page : 6 of 11 bns - od - c131/a4
lite - on technology corporation . p r o p e r t y o f l i t e - o n o n l y optical/electrical bin table iv spec. table specification luminous intensity unit: mcd @20ma bin code min. max. d 65 85 e 85 110 f 110 140 g 140 180 note: tolerance of each bin limit is 15% hue spec. table speci fication dominant wavelength unit : nm @20ma bin code min. max. h06 566.0 568.0 h07 568.0 570.0 h08 570.0 572.0 h09 572.0 574.0 h10 574.0 576.0 h11 576.0 578.0 note: tolerance of each bin limit is 1nm part no. : ltl307jgd - 041a page : 7 of 1 1 bns - od - c131/a4
lite - on technology corporation . p r o p e r t y o f l i t e - o n o n l y cautions 1. application the leds described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).c onsult liteons sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the leds may directly jeopardize life or health (such as in aviation, transportation, traffic con trol equipment, medical and life support systems and safety devices). 2. storage the storage ambient for the leds should not exceed 30c temperature or 70% relative humidity. it is recommended that leds out of their original packaging are used within three months. for extended storage out of their original packaging, it is recommended that the leds be stored in a sealed container with appropriate desiccant or in desiccators with nitrogen ambient. 3. cleaning use alcohol - based cleaning solvents such as isopr opyl alcohol to clean the leds if necessary. 4. lead forming & assembly during lead forming, the leads should be bent at a point at least 3mm from the base of led lens. do not use the base of the lead frame as a fulcrum during forming. lead forming must b e done before soldering, at normal temperature. during assembly on pcb, use minimum clinch force possible to avoid excessive mechanical stress. 5. soldering when soldering, for lamp without stopper type and must be leave a minimum of 2 mm clearance from t he base of the lens to the soldering point . to avoided the epoxy climb up on lead frame and was impact to non - soldering problem, dipping the lens into the solder must be avoided. do not apply any external stress to the lead frame during soldering while the led is at high temperature. recommended soldering conditions : soldering iron wave soldering temperature soldering time 3 5 0c max. 3 sec. max. (one time only) pre - heat pre - heat time solder wave soldering time 100c max. 60 sec. ma x. 260c max. 5 sec. max. note: excessive soldering temperature and/or time might result in deformation of the led lens or catastrophic failure of the led. ir reflow is not suitable process for through hole type led lamp product . part no. : ltl307jgd - 041a page : 8 of 1 1 bns - od - c131/a4
lite - on technology corporation . p r o p e r t y o f l i t e - o n o n l y 6. drive method an led is a current - operated device. in order to ensure intensity uniformity on multiple leds connected in parallel in an application, it is recommended that a current limiting re sistor be incorporated in the drive circuit, in series with each led as shown in circuit a below. circuit model a circuit model b (a) recommended circu it (b) the brightness of each led might appear different due to the differences in the i - v characteristics of those leds 7. esd (electrostatic discharge) static electricity or power surge will damage the led. suggestions to prevent esd dama ge: ? use a conductive wrist band or anti - electrostatic glove when handling these leds ? all devices, equipment, and machinery must be properly grounded ? work tables, storage racks, etc. should be properly grounded ? use ion blower to neutralize the static charg e which might have built up on surface of the leds plastic lens as a result of friction between leds during storage and handing part no. : ltl307jgd - 041a page : 9 of 1 1 bns - od - c131/a4 led led
lite - on technology corporation . p r o p e r t y o f l i t e - o n o n l y suggested checking list : training and certifi cation 1. everyone working in a static - safe area is esd - certified? 2. training records kept and re - certification dates monitored? static - safe workstation & work areas 1. static - safe workstation or work - areas have esd signs? 2. all surfaces and ob jects at all static - safe workstation and within 1 ft measure less than 100v? 3. all ionizer activated, positioned towards the units? 4. each work surface mats grounding is good? personnel grounding 1. every person (including visitors) handling esd se nsitive (esds) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. if conductive footwear used, conductive flooring also present where operator stand or walk? 3. garments, hairs or anything closer than 1 ft to esd items measure less than 100v*? 4. every wrist strap or heel strap/conductive shoes checked daily and result recorded for all dsl? 5. all wrist strap or heel strap checkers calibration up to date? note: *50v for blue led. device handling 1. every esds i tems identified by eia - 471 labels on item or packaging? 2. all esds items completely inside properly closed static - shielding containers when not at static - safe workstation? 3. no static charge generators (e.g. plastics) inside shielding containers w ith esds items? 4. all flexible conductive and dissipative package materials inspected before reuse or recycle? others 1. audit result reported to entity esd control coordinator? 2. corrective action from previous audits completed? 3. are audit records complete and on file? part no. : ltl307jgd - 041a page : 10 of 1 1 bns - od - c131/a4
lite - on technology corporation . p r o p e r t y o f l i t e - o n o n l y 8 . reliability test classification test item test condition reference standard endurance test operation life ta= under room tempera ture as per data sheet maximum rating * test time= 1000hrs ( - 24hrs,+72hrs) mil - std - 750d:1026 (1995) mil - std - 883d:1005 (1991) jis c 7021:b - 1 (1982) high temperature high humidity storage ta= 655 c rh= 90 95% test time= 240hrs2hrs mil - std - 20 2f: 103b(1980) jis c 7021 : b - 11(1982) high temperature storage ta= 1055 c * test time= 1000hrs ( - 24hrs,+72hrs) mil - std - 883d:1008 (1991) jis c 7021:b - 10 (1982) low temperature storage ta= - 555 c * test time=1000hrs ( - 24hrs,+72hrs) jis c 702 1:b - 12 (1982) environmental test temperature cycling 105 c 25 c - 55 c 25 c 30mins 5mins 30mins 5mins 10 cycles mil - std - 202f:107d (1980) mil - std - 750d:1051(1995) mil - std - 883d:1010 (1991) jis c 7021: a - 4(1982) thermal shock 105 5 c - 55 c 5 c 10mins 10mins 10 cycles mil - std - 20 2f:107d(1980) mil - std - 750d:1051(1995) mil - std - 883d:1011 (1991) solder resistance t.sol = 260 c max. dwell time= 5 secs max. 3 times dip mil - std - 202f:210a(1980) mil - std - 750d:2031(1995) jis c 7021: a - 1(1982) solderability t. sol = 230 5 c dwel l time= 5 1secs mil - std - 202f:208d(1980) mil - std - 750d:2026(1995) mil - std - 883d:2003(1991) jis c 7021: a - 2(1982) 9. others the appearance and specifications of the product may be modified for improvement, without prior notice. part no. : ltl307jgd - 041a page : 1 1 of 1 1 bns - od - c131/a4

▲Up To Search▲

Price & Availability of LTL307JGD-041A

	To Download LTL307JGD-041A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .