View ICPL3120_9045443.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 28/09/2017 ICPL3120 dd93213 isocom components description the ICPL3120 consists of an infrared light emitting diode optically coupled to an integrated circuit with a power driving output. ICPL3120 is ideally suitable to drive the power igbt and mosfet in inverters of motor controls and in power supplies. the 2.5a peak output current is capable to direct drive igbt/mosfet up to ratings of 1200v/100a. for igbts with higher ratings, ICPL3120 can be used to drive a discrete power stage which drives the igbt gate. features ? 2.5a maximum peak output current ? 35kv/ s minimum common mode rejection at v cm 1500v ? maximum propagation delay 500ns ? maximum propagation delay difference 100ns ? wide operating voltage range v cc 15 to 30 v ? maximum supply current i cc 3.5ma ? under voltage lock out (uvlo) protection with hysteresis ? guaranteed performance over temperature range - 40c to +105c ? msl 1 ? lead free and rohs compliant ? safety approvals pending applications ? igbt/mosfet gate drive ? ups ? inverters ? ac brushless and dc motor drives order information ? add g after pn for 10mm lead spacing ? add sm after pn for surface mount ? add smt&r after pn for surface mount tape & reel isocom components 2004 ltd unit 25b, park view road west, park view industrial estate hartlepool, cleveland, ts25 1pe, united kingdom tel : +44 (0)1429 863 609 fax : +44 (0)1429 863 581 e-mail : sales@isocom.co.uk http://www.isocom.com isocom components asia ltd hong kong office, block a, 8/f, wah hing industrial mansion, 36 tai yau street, san po kong, kowloon, hong kong. tel : +852 2995 9217 fax : +852 8161 6292 e-mail : sales@isocom.com.hk a 0.1 f bypass capacitor must be conn ected between pins 8 and 5. input forward current 20ma forward current rise / fall time 500ns power dissipation 45mw reverse voltage 5v forward peak current (pulse width 1 s, 300pps) 1a output peak output current (exponential waveform, pulse width 0.3 s, f = 15khz) 2.5a operating frequency (exponential waveform, i o(peak) l2.5al, pulse width 0.3 s) 50khz supply voltage (v cc ? v ee ) 0v to 35v output voltage 0v to v cc power dissipation 250mw isolation voltage 5000v rms total power dissipation 295mw operating temperature -40 to 105 c storage temperature -55 to 125 c lead soldering temperature (10s) 260c total package 1 nc 2 anode 3 cathode 4 nc 5 gnd (v ee ) 6 v o 7 v o 8 v cc absolute maximum ratings (t a = 25c) stresses exceeding the absolute maximum ratings can cause permanent damage to the device. exposure to absolute maximum ratings for long periods of time can adversely affect reliability.
2 28/09/2017 ICPL3120 dd93213 isocom components led v cc ? v ee (turn on, +ve going) v cc ? v ee (turn off ?ve going) v o off 0 ? 30v 0 ? 30v low on 0 ? 11.0v 0 ? 9.5v low truth table on 11.0 ? 13.5v 9.5 ? 12.0v transition on 13.5 ? 30v 12 ? 30v high parameter symbol min max unit operating temperature t a - 40 105 c supply voltage v cc ? v ee 15 30 v input current (on) i f(on) 7 16 ma input voltage (off) v f(off) 0 0.8 v recommended operating conditions
3 28/09/2017 ICPL3120 dd93213 isocom components electrical characteristics (typical values at v cc ? v ee = 30v and t a = 25c, minimum and maximum values at recommended operating conditions, unless otherwise specified) parameter symbol test condition min typ. max unit high level supply current i cch i f = 10ma, v cc = 30v v o = open 2.4 3.5 ma low level supply current i ccl i f = 0ma, v cc = 30v v o = open 2.5 3.5 ma high level output current i oh maximum pulse width = 50 s v o = v cc ? 1.5v -1.0 a maximum pulse width = 10 s v o = v cc ? 4v -2.5 low level output current i ol maximum pulse width = 50 s v o = v ee + 1.5v 1.0 a maximum pulse width = 10 s v o = v ee + 4v 2.5 high level output voltage v oh i f = 10ma, i o = -100ma v cc ? 0.3 v cc ? 0.1 v low level output voltage v ol i f = 0ma, i o = 100ma v ee +0.1 v ee +0.25 v uvlo threshold v uvlo+ v o > 5v, i f = 10ma 11.0 12.7 13.5 v v uvlo- v o < 5v, i f = 10ma 9.5 11.2 12.0 v uvlo hysteresis uvlo hys 1.5 v output parameter symbol test condition min typ. max unit forward voltage v f i f = 10ma 1.2 1.37 1.8 v forward voltage temperature coefficient v f / t i f = 10ma ? 1.237 mv/c reverse voltage v r i r = 10 a 5 v input threshold current (low to high) i flh v cc = 30v v o > 5v 1.8 5 ma input threshold voltage (high to low) v fhl v cc = 30v v o < 5v 0.8 v input capacitance c in v f = 0v, f = 1mhz 33 pf input
4 28/09/2017 ICPL3120 dd93213 isocom components electrical characteristics (typical values at v cc ? v ee = 30v and t a = 25c, minimum and maximum values at recommended operating conditions, unless otherwise specified) parameter symbol test condition min typ. max unit propagation delay time to high output level t plh i f = 7 to 16ma, v cc = 15 to 30v, v ee = 0v, rg = 10 ? , cg = 25nf, f = 10khz, duty cycle = 50% 50 130 500 ns propagation delay time to low output level t phl 50 130 500 pulse width distortion |t phl - t plh | for any given device pwd 5 70 propagation delay difference (t phl - t plh ) between any two devices pdd -100 100 output rise time (10% to 90%) t r 35 output fall time (90% to 10%) t f 35 common mode transient immunity at high output level cm h i f = 10 to 16ma, v cc = 30v, v cm = 1500v, t a = 25c 35 50 kv/ s common mode transient immunity at low output level cm l v f = 0v, v cc = 30v, v cm = 1500v, t a = 25c 35 50 kv/ s switching uvlo turn off delay t uvlo off i f = 10ma, v o < 5v 0.4 s uvlo turn on delay t uvlo on i f = 10ma, v o > 5v 1.6 s
5 28/09/2017 ICPL3120 dd93213 isocom components electrical characteristics (typical values at v cc ? v ee = 30v and t a = 25c, minimum and maximum values at recommended operating conditions, unless otherwise specified) note : 1. a 0.1uf or bigger bypass capacitor must be connected across pin 8 and pin 5. 2. pdd is the difference of t phl and t plh between any two ICPL3120 under same test conditions. 3. common mode transient immunity in high stage is the maximum tolerable negative dv cm /dt on the trailing edge of the common mode impulse signal, v cm , to assure that the output will remain high (v o > 15v). 4. common mode transient immunity in low stage is the maximum tolerable positive dv cm /dt on the leading edge of the common mode impulse signal, v cm , to assure that the output will remain low (v o < 1v). parameter symbol test condition min typ. max unit insulation voltage v iso r.h. = 40% - 60%, t a = 25c t = 1 min, 5000 v input - output resistance r i-o v i-o = 500vdc 10 12 ? input - output capacitance c i-o f = 1mhz 0.92 pf isolation
6 28/09/2017 ICPL3120 dd93213 isocom components fig 1 supply current vs supply voltage fig 2 supply current vs ambient temperature fig 3 transfer characteristics fig 4 output low voltage vs ambient temperature fig 5 output high voltage vs ambient temperature fig 6 output high voltage drop vs ambient temperature
7 28/09/2017 ICPL3120 dd93213 isocom components fig 7 input threshold current vs ambient temperature fig 8 propagation delay vs ambient temperature fig 9 propagation delay vs forward current fig 10 propagation delay vs supply voltage fig 11 propagation delay vs series load resistance fig 12 propagation delay vs series load capacitance
8 28/09/2017 ICPL3120 dd93213 isocom components fig 13 forward curren t vs forward voltage v ol test circuit i oh test circuit i ol test circuit v oh test circuit
9 28/09/2017 ICPL3120 dd93213 isocom components i flh test circuit uvlo test circuit cmr test circuit t r , t f , t plh and t phl test circuit
10 28/09/2017 ICPL3120 dd93213 isocom components order information device marking after pn description packing quantity none standard dip8 50 pcs per tube g 10mm lead spacing 50 pcs per tube sm surface mount 50 pcs per tube smt&r surface mount tape & reel 1000 pcs per reel ICPL3120 pn ICPL3120 ICPL3120g ICPL3120sm ICPL3120smt&r ICPL3120 i yww ICPL3120 denotes device part number y denotes 1 digit year code ww denotes 2 digit week code i denotes isocom
11 28/09/2017 ICPL3120 dd93213 isocom components package dimensions in mm (inch) dip g form smd
12 28/09/2017 ICPL3120 dd93213 isocom components description symbol dimension mm (inch) tape width w 16 0.3 (0.63) pitch of sprocket holes p 0 4 0.1 (0.15) f 7.5 0.1 (0.295) p 2 2 0.1 (0.079) distance of compartment to compartment p 1 12 0.1 (0.47) distance of compartment to sprocket holes recommended solder pad layout (mm) tape and reel packaging
13 28/09/2017 ICPL3120 dd93213 isocom components ir reflow soldering temperature profile note : one time reflow soldering is recommended. do not immerse device body in solder paste. time (s) temp (c) ! 25c t s preheat 60s ? 120s t smin t smax 260c t l 217c time 25c to peak temperature t p t p - 5c t p max ramp up rate 3c/s max ramp down rate 6c/s t l 200c 150c profile details conditions preheat - min temperature (t smin ) - max temperature (t smax ) - time t smin to t smax (t s ) 150c 200c 60s - 120s soldering zone - peak temperature (t p ) - time at peak temperature - liquidous temperature (t l ) - time within 5c of actual peak temperature (t p ? 5c) - time maintained above t l (t l ) - ramp up rate (t l to t p ) - ramp down rate (t p to t l ) 260c 10s max 217c 30s max 60s - 100s 3c/s max 6c/s max average ramp up rate (t smax to t p ) 3c/s max time 25c to peak temperature 8 minutes max
14 28/09/2017 disclaimer dd93213 isocom components isocom components is continually working to im prove the quality and reliability of its products. nevertheless, semiconductor devices in general c an malfunction or fail due to their inherent electrical sensitivity and vulner ability to physical stress. it is the responsibilit y of the buyer, when utilizing isocom components products, to co mply with the standards of safety in making a safe design for the entire system, and to avoid si tuations in which a malf unction or failure of such isocom components products could cause loss of human life, bodily injury or damage to property. in developing your designs, please ensure t hat isocom components pr oducts are used within specified operating ranges as set forth in the most recent isocom components products specifications. the isocom components products listed in this document are intended for usage in general electronics applications (computer, personal equi pment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). these isocom components products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (?unintended usage ?). unintended usage include atomic energy control instruments, airplane or spaceship instru ments, transportation inst ruments, traffic signal instruments, combustion c ontrol instruments, m edical instruments, all types of safety devices, etc... unintended usage of isocom components products listed in this document shall be made at the cu stomer?s own risk. gallium arsenide (gaas) is a substance used in the products described in this document. gaas dust and fumes are toxic. do not break, cut or pulverize the product, or use chemicals to dissolve them. when disposing of the products, fo llow the appropriate regulations. do not dispose of the products with other i ndustrial waste or with domestic garbage. the products described in this document are s ubject to the foreign ex change and foreign trade laws. the information contained herein is presented only as a guide for the applications of our products. no responsibility is assumed by isocom components for any infringe ments of intellectual property or ot her rights of the third parties which ma y result from its use. no license is granted by implication or other wise under any intellectual prope rty or other rights of isocom components or others. the information contained herein is subject to change without notice.

▲Up To Search▲

Price & Availability of ICPL3120

	To Download ICPL3120 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .